SIST EN 50379-3:2012
(Main)Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances
This European Standard covers apparatus designed for checking the performance of heating appliances by measuring flue gas parameters of gas fired heating appliances for domestic residential and commercial applications. The apparatus may consist of different functional modules which may be tested separately for complying with this standard, and will be combined in different ways according to the different applications. Part 1 of EN 50379 specifies the general requirements and is supplemented by the requirements in EN 50379 2 and/or EN 50379 3. This European Standard specifies the performance requirements of portable spot reading apparatus designed to detect specific combustion flue gas parameters, such as concentration of gaseous compounds, temperature and/or pressure, to be used to decide if maintenance for the appliance is required and for adjusting the appliance during maintenance. This European Standard excludes apparatus for – checking appliances using fuels other than gas, – continuous emission, safety monitoring and control, and – use in vessels with an international load line. NOTE 1 When this apparatus is used in industrial premises, national regulations should be observed. NOTE 2 Apparatus may contain functional modules which are not covered by this standard e.g. measurement of smoke spot number (see EN 267:2009+A1:2011, Annex A) and/or measurement of indoor ambient air (see EN 50543).
Anforderungen an tragbare elektrische Geräte zur Messung von Verbrennungsparametern von Heizungsanlagen - Teil 3: Anforderungen an das Betriebsverhalten von Geräten für den Einsatz im nicht-geregelten Bereich bei Wartungen von gasbefeuerten Heizungsanlagen
Spécification pour les appareils électriques portatifs conçus pour mesurer les paramètres des gaz de combustion dans les conduits d'évacuation des appareils de chauffage - Partie 3: Prescriptions des caractéristiques des appareils utilisés dans le service après-vente hors champ réglementaire des appareils de chauffage à gaz
Specifikacija za prenosne električne naprave za merjenje parametrov dimnih plinov grelnih naprav - 3. del: Zahtevane lastnosti za naprave, ki se uporabljajo pri vzdrževanju plinskih grelnih naprav, ki ni zakonsko predpisano
Ta evropski standard zajema naprave za preverjanje učinkovitosti grelnih naprav z merjenjem parametrov izpušnega plina plinskih grelnih naprav za gospodinjske in komercialne uporabe. Napravo lahko sestavljajo različni funkcionalni moduli, ki se združujejo na različne načine v skladu z različnimi uporabami, pri čemer je mogoče ločeno preskusiti njihovo skladnost s tem standardom. 1. del standarda EN 50379 določa splošne zahteve in je dopolnjen z zahtevami v standardu EN 50379-2 in/ali EN 50379-3. Ta evropski standard določa zahteve za delovanje prenosnih odčitovalnih naprav za zaznavanje posebnih parametrov vnetljivosti izpušnega plina, kot so koncentracija plinastih spojin, temperatura in/ali tlak, za odločanje, ali je potrebno vzdrževanje naprave, in za prilagajanje naprave med vzdrževanjem. Ta evropski standard ne zajema naprav za: – preverjanje naprav, ki za gorivo ne uporabljajo plina, – trajno spremljanje in nadzor emisij in varnosti ter – uporabo v posodah z mednarodno tovorno črto.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50379-3:2012
01-junij-2012
Specifikacija za prenosne električne naprave za merjenje parametrov dimnih
plinov grelnih naprav - 3. del: Zahtevane lastnosti za naprave, ki se uporabljajo pri
vzdrževanju plinskih grelnih naprav, ki ni zakonsko predpisano
Specification for portable electrical apparatus designed to measure combustion flue gas
parameters of heating appliances - Part 3: Performance requirements for apparatus used
in non-statutory servicing of gas fired heating appliances
Anforderungen an tragbare elektrische Geräte zur Messung von
Verbrennungsparametern von Heizungsanlagen - Teil 3: Anforderungen an das
Betriebsverhalten von Geräten für den Einsatz im nicht-geregelten Bereich bei
Wartungen von gasbefeuerten Heizungsanlagen
Spécification pour les appareils électriques portatifs conçus pour mesurer les paramètres
des gaz de combustion dans les conduits d'évacuation des appareils de chauffage -
Partie 3: Prescriptions des caractéristiques des appareils utilisés dans le service après-
vente hors champ réglementaire des appareils de chauffage à gaz
Ta slovenski standard je istoveten z: EN 50379-3:2012
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
SIST EN 50379-3:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50379-3:2012
---------------------- Page: 2 ----------------------
SIST EN 50379-3:2012
EUROPEAN STANDARD
EN 50379-3
NORME EUROPÉENNE
April 2012
EUROPÄISCHE NORM
ICS 13.320 Supersedes EN 50379-3:2004
English version
Specification for portable electrical apparatus designed to measure
combustion flue gas parameters of heating appliances -
Part 3: Performance requirements for apparatus used in non-statutory
servicing of gas fired heating appliances
Spécification pour les appareils Anforderungen an tragbare elektrische
électriques portatifs conçus pour mesurer Geräte zur Messung von
les paramètres des gaz de combustion Verbrennungsparametern von
dans les conduits d'évacuation des Heizungsanlagen -
appareils de chauffage - Teil 3: Anforderungen an das
Partie 3: Prescriptions des Betriebsverhalten von Geräten für den
caractéristiques des appareils utilisés Einsatz im nicht-geregelten Bereich bei
dans le service après-vente hors champ Wartungen von gasbefeuerten
réglementaire des appareils de chauffage Heizungsanlagen
à gaz
This European Standard was approved by CENELEC on 2012-03-19. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50379-3:2012 E
---------------------- Page: 3 ----------------------
SIST EN 50379-3:2012
EN 50379-3:2012 – 2 –
Contents
Foreword . 3
Introduction. 4
1 Sc op e . . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 6
5 Test methods and performance requirements . 6
5.1 General requirements for tests . 6
5.2 Normal conditions for tests . 6
5.3 Mechanical tests . 6
5.4 Electrical and software tests . 7
5.5 Tests with test gases . 7
5.6 Tests with real flue gases . 8
5.7 Calculated values . 9
5.8 Temperature . 9
5.9 Pressure . 10
Bibliography . 11
---------------------- Page: 4 ----------------------
SIST EN 50379-3:2012
– 3 – EN 50379-3:2012
Foreword
This document (EN 50379-3:2012) has been prepared by CLC/TC 216 "Gas detectors".
The following dates are fixed:
• latest date by which this document has (dop) 2013-03-19
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-03-19
• latest date by which the national
standards conflicting with this
document have to be withdrawn
This document supersedes EN 50379-3:2004.
EN 50379-3:2012 includes the following significant technical changes with respect to EN 50379-3:2004:
— 5.5.7 considers calibration curves for sensors with nonlinear signal;
— 5.5.8 considers influence of pressure variations;
— 5.5.9 considers the influence of water vapour on the gas signal;
— 5.7.2 for calculated values was amended;
— 5.9.1 was amended to cover measurement at the circular orifice.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
__________
---------------------- Page: 5 ----------------------
SIST EN 50379-3:2012
EN 50379-3:2012 – 4 –
Introduction
This European Standard covers apparatus for measuring gas concentrations and other combustion
parameters, as used in the installation and maintenance of heating appliances. It forms a specification for
portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances,
and includes the following parts under the generic title Specification for portable electrical apparatus designed
to measure combustion flue gas parameters of heating appliances:
Part 1: General requirements and test methods;
Part 2: Performance requirements for apparatus used in statutory inspections and assessments;
Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating
appliances.
EN 50379-1 specifies general requirements for the construction, testing and performance of portable spot
reading apparatus, designed to give an assessment of specific combustion flue gas parameters such as
concentration of gaseous compounds, temperature and/or pressure, to check the combustion performance of
heating appliances for domestic residential and commercial applications using commercially available fuels.
EN 50379-2 is for apparatus intended to be used for statutory measurement. In several European countries,
legal requirements exist for the performance of heating appliances. Authorised inspectors use these
apparatus to measure the flue gas parameters, in order to test the compliance with national regulations. Due
to the legal consequences resulting from the measurement there are strict requirements regarding the
measuring uncertainty of these apparatus. Therefore EN 50379-2 includes maximum values for measuring
uncertainty of the apparatus. Tests with real flue gases form a key part of the verification of the performance
of the apparatus for statutory measurement. The measuring uncertainty has to be justified by internationally
accepted methods over the whole measuring range.
EN 50379-3 is for apparatus intended to be used for non-statutory applications. There are reduced
performance requirements, because the apparatus are designed to decide whether maintenance for a gas
fired appliance is required, and for adjusting the appliance during maintenance. There will be no
determination of the measuring uncertainty for the apparatus.
---------------------- Page: 6 ----------------------
SIST EN 50379-3:2012
– 5 – EN 50379-3:2012
1 Scope
This European Standard covers apparatus designed for checking the performance of heating appliances by
measuring flue gas parameters of gas fired heating appliances for domestic residential and commercial
applications.
The apparatus may consist of different functional modules which may be tested separately for complying with
this standard, and will be combined in different ways according to the different applications. Part 1 of
EN 50379 specifies the general requirements and is supplemented by the requirements in EN 50379-2 and/or
EN 50379-3.
This European Standard specifies the performance requirements of portable spot reading apparatus
designed to detect specific combustion flue gas parameters, such as concentration of gaseous compounds,
temperature and/or pressure, to be used to decide if maintenance for the appliance is required and for
adjusting the appliance during maintenance.
This European Standard excludes apparatus for
– checking appliances using fuels other than gas,
– continuous emission, safety monitoring and control, and
– use in vessels with an international load line.
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Anforderungen an tragbare elektrische Geräte zur Messung von Verbrennungsparametern von Heizungsanlagen - Teil 3: Anforderungen an das Betriebsverhalten von Geräten für den Einsatz im nicht-geregelten Bereich bei Wartungen von gasbefeuerten HeizungsanlagenSpécification pour les appareils électriques portatifs conçus pour mesurer les paramètres des gaz de combustion dans les conduits d'évacuation des appareils de chauffage - Partie 3: Prescriptions des caractéristiques des appareils utilisés dans le service après-vente hors champ réglementaire des appareils de chauffage à gazSpecification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances91.140.10Sistemi centralnega ogrevanjaCentral heating systems13.040.40Stationary source emissionsICS:Ta slovenski standard je istoveten z:EN 50379-3:2012SIST EN 50379-3:2012en01-junij-2012SIST EN 50379-3:2012SLOVENSKI
STANDARD
SIST EN 50379-3:2012
EUROPEAN STANDARD EN 50379-3 NORME EUROPÉENNE
EUROPÄISCHE NORM April 2012
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50379-3:2012 E
ICS 13.320 Supersedes EN 50379-3:2004
English version
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances -
Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances
Spécification pour les appareils électriques portatifs conçus pour mesurer les paramètres des gaz de combustion dans les conduits d'évacuation des appareils de chauffage -
Partie 3: Prescriptions des caractéristiques des appareils utilisés dans le service après-vente hors champ réglementaire des appareils de chauffage à gaz
Anforderungen an tragbare elektrische Geräte zur Messung von Verbrennungsparametern von Heizungsanlagen -
Teil 3: Anforderungen an das Betriebsverhalten von Geräten für den Einsatz im nicht-geregelten Bereich bei Wartungen von gasbefeuerten Heizungsanlagen
This European Standard was approved by CENELEC on 2012-03-19. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 50379-3:2012
EN 50379-3:2012 – 2 –
Contents Foreword . 3Introduction. 41Scope . 52Normative references . 53Terms and definitions . 54General requirements . 65Test methods and performance requirements . 65.1General requirements for tests . 65.2Normal conditions for tests . 65.3Mechanical tests . 65.4Electrical and software tests . 75.5Tests with test gases . 75.6Tests with real flue gases . 85.7Calculated values . 95.8Temperature . 95.9Pressure . 10Bibliography . 11 SIST EN 50379-3:2012
– 3 – EN 50379-3:2012 Foreword This document (EN 50379-3:2012) has been prepared by CLC/TC 216 "Gas detectors". The following dates are fixed:
• latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-03-19 • latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2015-03-19
This document supersedes EN 50379-3:2004.
EN 50379-3:2012 includes the following significant technical changes with respect to EN 50379-3:2004:
— 5.5.7 considers calibration curves for sensors with nonlinear signal;
— 5.5.8 considers influence of pressure variations;
— 5.5.9 considers the influence of water vapour on the gas signal;
— 5.7.2 for calculated values was amended;
— 5.9.1 was amended to cover measurement at the circular orifice.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
__________ SIST EN 50379-3:2012
EN 50379-3:2012 – 4 – Introduction This European Standard covers apparatus for measuring gas concentrations and other combustion parameters, as used in the installation and maintenance of heating appliances. It forms a specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances, and includes the following parts under the generic title Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances: Part 1: General requirements and test methods; Part 2: Performance requirements for apparatus used in statutory inspections and assessments; Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances. EN 50379-1 specifies general requirements for the construction, testing and performance of portable spot reading apparatus, designed to give an assessment of specific combustion flue gas parameters such as concentration of gaseous compounds, temperature and/or pressure, to check the combustion performance of heating appliances for domestic residential and commercial applications using commercially available fuels. EN 50379-2 is for apparatus intended to be used for statutory measurement. In several European countries, legal requirements exist for the performance of heating appliances. Authorised inspectors use these apparatus to measure the flue gas parameters, in order to test the compliance with national regulations. Due to the legal consequences resulting from the measurement there are strict requirements regarding the measuring uncertainty of these apparatus. Therefore EN 50379-2 includes maximum values for measuring uncertainty of the apparatus. Tests with real flue gases form a key part of the verification of the performance of the apparatus for statutory measurement. The measuring uncertainty has to be justified by internationally accepted methods over the whole measuring range. EN 50379-3 is for apparatus intended to be used for non-statutory applications. There are reduced performance requirements, because the apparatus are designed to decide whether maintenance for a gas fired appliance is required, and for adjusting the appliance during maintenance. There will be no determination of the measuring uncertainty for the apparatus. SIST EN 50379-3:2012
– 5 – EN 50379-3:2012 1 Scope This European Standard covers apparatus designed for checking the performance of heating appliances by measuring flue gas parameters of gas fired heating appliances for domestic residential and commercial applications. The apparatus may consist of different functional modules which may be tested separately for complying with this standard, and will be combined in different ways according to the different applications. Part 1 of EN 50379 specifies the general requirements and is supplemented by the requirements in EN 50379-2 and/or EN 50379-3. This European Standard specifies the performance requirements of portable spot reading apparatus designed to detect specific combustion flue gas parameters, such as concentration of gaseous compounds, temperature and/or pressure, to be used to decide if maintenance for the appliance is required and for adjusting the appliance during maintenance. This European Standard excludes apparatus for – checking appliances using fuels other than gas, – continuous emission, safety monitoring and control, and – use in vessels with an international load line. NOTE 1 When this apparatus is used in industrial premises, national regulations should be observed. NOTE 2 Apparatus may contain functional modules which are no
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.