SIST EN ISO 10893-11:2011
(Main)Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011)
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011)
This part of ISO 10893 specifies requirements for the automated ultrasonic shear wave (generated by conventional or phased array technique) testing of the weld seam of submerged arc-welded (SAW) or electric resistance and induction-welded (EW) steel tubes. For SAW tubes, the test covers the detection of imperfections oriented predominantly parallel to or, by agreement, perpendicular to the weld seam or both. For EW tubes, the test covers the detection of imperfections oriented predominantly parallel to the weld seam. In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the manufacturer. For the detection of imperfections at the weld seam of EW tubes, full peripheral ultrasonic testing is possible. This part of ISO 10893 can also be applicable to the testing of circular hollow sections.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 11: Automatisierte Ultraschallprüfung der Schweißnaht geschweißter Stahlrohre zum Nachweis von Unvollkommenheiten in Längs- und/oder Querrichtung (ISO 10893-11:2011)
Dieser Teil der ISO 10893 legt die Anforderungen an die automatisierte Ultraschallprüfung unter Anwendung von Transversalwellen (erzeugt mittels konventioneller oder mittels Phased-Array-Technik) der Schweißnaht unterpulvergeschweißter (SAW-), elektrisch geschweißter oder induktionsgeschweißter (EW-) Stahlrohre fest. Für unterpulvergeschweißte (SAW-) Stahlrohre umfasst die Prüfung das Auffinden von Unvollkommenheiten, die vorwiegend parallel und/oder nach Vereinbarung rechtwinklig zur Schweißnaht verlaufen. Für elektrisch geschweißte oder induktionsgeschweißte (EW-) Stahlrohre umfasst die Prüfung das Auffinden der Unvollkommenheiten vorwiegend parallel zur Schweißnaht. Bei Prüfung auf Unvollkommenheiten in Längsrichtung darf nach Wahl des Herstellers mit Plattenwellen geprüft werden. Zum Nachweis der Unvollkommenheiten an der Schweißnaht bei EW-Rohren wird die Ultraschallprüfung über den gesamten Umfang akzeptiert. Dieses Dokument kann auch für die Prüfung von kreisförmigen Hohlprofilen angewendet werden. ANMERKUNG Ultraschallprüfungen über den gesamten Umfang für nahtlose und geschweißte (ausgenommen unterpulverschweißter) Rohre sind in der ISO 10893-10 festgelegt.
Essais non destructifs des tubes en acier - Partie 11: Contrôle automatisé par ultrasons du cordon de soudure des tubes en acier soudés pour la détection des imperfections longitudinales et/ou transversales (ISO 10893-11:2011)
L'ISO 10893-11:2011 spécifie les exigences relatives au contrôle par ultrasons, avec ondes de cisaillement (générées par une technique conventionnelle ou la technique des réseaux à commande de phase), du cordon de soudure des tubes en acier soudés à l'arc immergé sous flux en poudre (SAW) ou des tubes en acier soudés par résistance électrique ou induction (EW).
Pour les tubes SAW, le contrôle couvre la détection des imperfections principalement orientées parallèlement et/ou, par accord, perpendiculairement au cordon de soudure.
Pour les tubes EW, le contrôle couvre la détection des imperfections principalement orientées parallèlement au cordon de soudure. Dans le cas de contrôle des imperfections longitudinales, un contrôle par ondes de Lamb peut être utilisé au choix du producteur.
L'ISO 10893-11:2011 est également applicable au contrôle des profils creux circulaires.
Neporušitveno preskušanje jeklenih cevi - 11. del: Avtomatizirano ultrazvočno preskušanje varjenega šiva varjenih jeklenih cevi za odkrivanje vzdolžnih in/ali prečnih nepopolnosti (ISO 10893-11:2011)
Ta del ISO 10893 določa zahteve za avtomatsko preiskavo vara jeklenih cevi, obločno varjenih pod praškom (SAW), ali električne upornosti in indukcijsko varjenih (EW) jeklenih cevi z ultrazvočnim strižnim valovanjem (ki nastane s konvencionalno tehniko ali tehniko faznih nizov). Za cevi SAW preskus zajema predvsem odkrivanje napak, usmerjenih vzporedno z varom ali po dogovoru pravokotno na var ali oboje. Za cevi EW preskus zajema predvsem odkrivanje napak, usmerjenih vzporedno z varom. Pri preskušanju vzdolžnih napak se po presoji proizvajalca lahko uporabi preskušanje z Lambovim valovanjem. Za odkrivanje napak na varu cevi EW je mogoča ultrazvočna preiskava po celotnem obodu. Ta del ISO 10893 lahko velja tudi za preskušanje krožnih votlih delov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10893-11:2011
01-november-2011
Nadomešča:
SIST EN 10246-8:2000
SIST EN 10246-9:2000
Neporušitveno preskušanje jeklenih cevi - 11. del: Avtomatizirano ultrazvočno
preskušanje varjenega šiva varjenih jeklenih cevi za odkrivanje vzdolžnih in/ali
prečnih nepopolnosti (ISO 10893-11:2011)
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld
seam of welded steel tubes for the detection of longitudinal and/or transverse
imperfections (ISO 10893-11:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 11: Automatisierte Ultraschallprüfung der
Schweißnaht geschweißter Stahlrohre zum Nachweis von Unvollkommenheiten in
Längs- und/oder Querrichtung (ISO 10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Contrôle automatisé par ultrasons
du cordon de soudure des tubes en acier soudés pour la détection des imperfections
longitudinales et/ou transversales (ISO 10893-11:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-11:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
25.160.40 Varjeni spoji in vari Welded joints and welds
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-11:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-11:2011
EUROPEAN STANDARD
EN ISO 10893-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-8:1999, EN 10246-9:2000
English Version
Non-destructive testing of steel tubes - Part 11: Automated
ultrasonic testing of the weld seam of welded steel tubes for the
detection of longitudinal and/or transverse imperfections (ISO
10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Zerstörungsfreie Prüfung von Stahlrohren - Teil 11:
Contrôle automatisé par ultrasons du cordon de soudure Automatisierte Ultraschallprüfung der Schweißnaht
des tubes en acier soudés pour la détection des geschweißter Stahlrohre zum Nachweis von
imperfections longitudinales et/ou transversales (ISO Unvollkommenheiten in Längs- und/oder Querrichtung (ISO
10893-11:2011) 10893-11:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-11:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Foreword
This document (EN ISO 10893-11:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-8:1999, EN 10246-9:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10893-11:2011 has been approved by CEN as a EN ISO 10893-11:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10893-11:2011
INTERNATIONAL ISO
STANDARD 10893-11
First edition
2011-04-01
Non-destructive testing of steel tubes —
Part 11:
Automated ultrasonic testing of the weld
seam of welded steel tubes for the
detection of longitudinal and/or
transverse imperfections
Essais non destructifs des tubes en acier —
Partie 11: Contrôle automatisé par ultrasons du cordon de soudure des
tubes en acier soudés pour la détection des imperfections
longitudinales et/ou transversales
Reference number
ISO 10893-11:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 General requirements .2
5 Test method .3
6 Reference tube.4
6.1 General .4
6.2 Reference notches .5
6.3 Reference hole.6
7 Equipment calibration and checking.7
7.1 General .7
7.2 Adjustment of the trigger/alarm level.7
7.3 Calibration check and recalibration .7
8 Acceptance .8
9 Test report.8
Annex A (normative) Manual/semi-automated testing of untested ends and suspect areas .9
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10893-11 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 19, Technical
delivery conditions for steel tubes for pressure purposes.
This first edition cancels and replaces ISO 9764:1989 and ISO 9765:1990, which have been technically
revised.
ISO 10893 consists of the following parts, under the general title Non-destructive testing of steel tubes:
⎯ Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel
tubes for the verification of leaktightness
⎯ Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel
tubes for the detection of imperfections
⎯ Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged
arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections
⎯ Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface
imperfections
⎯ Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of
surface imperfections
⎯ Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections
⎯ Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of
imperfections
⎯ Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar
imperfections
⎯ Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the
manufacture of welded steel tubes
⎯ Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged
arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
⎯ Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of
longitudinal and/or transverse imperfections
⎯ Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except
submerged arc-welded) steel tubes
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 12 ----------------------
SIST EN ISO 10893-11:2011
INTERNATIONAL STANDARD ISO 10893-11:2011(E)
Non-destructive testing of steel tubes —
Part 11:
Automated ultrasonic testing of the weld seam of welded steel
tubes for the detection of longitudinal and/or transverse
imperfections
1 Scope
This part of ISO 10893 specifies requirements for the automated ultrasonic shear wave (generated by
conventional or phased array technique) testing of the weld seam of submerged arc-welded (SAW) or electric
resistance and induction-welded (EW) steel tubes.
For SAW tubes, the test covers the detection of imperfections oriented predominantly parallel to or, by
agreement, perpendicular to the weld seam or both.
For EW tubes, the test covers the detection of imperfections oriented predominantly parallel to the weld seam.
In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the
manufacturer.
For the detection of imperfections at the weld seam of EW tubes, full peripheral ultrasonic testing is possible.
This part of ISO 10893 can also be applicable to the testing of circular hollow sections.
NOTE For full peripheral ultrasonic testing of seamless and welded (except SAW) tubes, see ISO 10893-10.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5577, Non-destructive testing — Ultrasonic inspection — Vocabulary
ISO 9712, Non-destructive testing — Qualification and certification of personnel
ISO 10893-6, Non-destructive testing of steel tubes — Part 6: Radiographic testing of the weld seam of
welded steel tubes for the detection of imperfections
ISO 10893-7, Non-destructive testing of steel tubes — Part 7: Digital radiographic testing of the weld seam of
welded steel tubes for the detection of imperfections
ISO 11484, Steel products — Employer's qualification system for non-destructive testing (NDT) personnel
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5577 and ISO 11484 and the
following apply.
3.1
reference standard
standard for the calibration of non-destructive testing equipment (e.g. drill holes, notches, recesses)
3.2
reference tube
tube or length of tube containing the reference standard(s)
3.3
reference sample
sample (e.g. segment of tube, plate or strip) containing the reference standard(s)
NOTE Only the term “reference tube” is used in this part of ISO 10893, also covering the term “reference sample”.
3.4
tube
hollow long product open at both ends, of any cross-sectional shape
3.5
welded tube
ttube made by forming a hollow profile from a flat product and welding adjacent edges together. After welding
the tube may be further processed, either hot or cold, into its final dimensions
3.6
electric welded tube
tube made by pressure welding, in a continuous or non-continuous process, in which strip is formed cold into
a hollow profile and the seam weld made by heating the adjacent edges through the resistance to the passage
of high- or low-frequency current, and pressing the edges together
NOTE The electric current can be applied either by direct electrode contact or by induction.
3.7
manufacturer
organization that manufactures products in accordance with the relevant standard(s) and declares the
compliance of the delivered products with all applicable provisions of the relevant standard(s)
3.8
agreement
contractual arrangement between the manufacturer and purchaser at the time of enquiry and order
4 General requirements
4.1 Unless otherwise specified by the product standards or agreed on by the purchaser and manufacturer,
an ultrasonic test shall be carried out on tubes after completion of all the primary production process
operations (rolling, heat treating, cold and hot working, sizing and primary straightening, etc.).
For cold-expanded tubes, the ultrasonic testing of the weld shall be carried out
...
SLOVENSKI STANDARD
SIST EN ISO 10893-11:2011
01-november-2011
1DGRPHãþD
SIST EN 10246-8:2000
SIST EN 10246-9:2000
1HSRUXãLWYHQRSUHVNXãDQMHMHNOHQLKFHYLGHO 8JRWDYOMDQMHY]GROåQLKLQDOL
SUHþQLKQDSDNYDUDSULMHNOHQLKFHYHKREORþQRYDUMHQLKSRGSUDãNRP]
DYWRPDWVNRXOWUD]YRþQRSUHLVNDYR ,62
Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld
seam of welded steel tubes for the detection of longitudinal and/or transverse
imperfections (ISO 10893-11:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 11: Automatisierte Ultraschallprüfung der
Schweißnaht geschweißter Stahlrohre zum Nachweis von Unvollkommenheiten in Längs
- und/oder Querrichtung (ISO 10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Contrôle automatisé par ultrasons
du cordon de soudure des tubes en acier soudés pour la détection des imperfections
longitudinales et/ou transversales (ISO 10893-11:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-11:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
25.160.40 Varjeni spoji in vari Welded joints
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-11:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-11:2011
EUROPEAN STANDARD
EN ISO 10893-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-8:1999, EN 10246-9:2000
English Version
Non-destructive testing of steel tubes - Part 11: Automated
ultrasonic testing of the weld seam of welded steel tubes for the
detection of longitudinal and/or transverse imperfections (ISO
10893-11:2011)
Essais non destructifs des tubes en acier - Partie 11: Zerstörungsfreie Prüfung von Stahlrohren - Teil 11:
Contrôle automatisé par ultrasons du cordon de soudure Automatisierte Ultraschallprüfung der Schweißnaht
des tubes en acier soudés pour la détection des geschweißter Stahlrohre zum Nachweis von
imperfections longitudinales et/ou transversales (ISO Unvollkommenheiten in Längs- und/oder Querrichtung (ISO
10893-11:2011) 10893-11:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-11:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-11:2011
EN ISO 10893-11:2011 (E)
Foreword
This document (EN ISO 10893-11:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-8:1999, EN 10246-9:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10893-11:2011 has been approved by CEN as a EN ISO 10893-11:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10893-11:2011
INTERNATIONAL ISO
STANDARD 10893-11
First edition
2011-04-01
Non-destructive testing of steel tubes —
Part 11:
Automated ultrasonic testing of the weld
seam of welded steel tubes for the
detection of longitudinal and/or
transverse imperfections
Essais non destructifs des tubes en acier —
Partie 11: Contrôle automatisé par ultrasons du cordon de soudure des
tubes en acier soudés pour la détection des imperfections
longitudinales et/ou transversales
Reference number
ISO 10893-11:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 General requirements .2
5 Test method .3
6 Reference tube.4
6.1 General .4
6.2 Reference notches .5
6.3 Reference hole.6
7 Equipment calibration and checking.7
7.1 General .7
7.2 Adjustment of the trigger/alarm level.7
7.3 Calibration check and recalibration .7
8 Acceptance .8
9 Test report.8
Annex A (normative) Manual/semi-automated testing of untested ends and suspect areas .9
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10893-11 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 19, Technical
delivery conditions for steel tubes for pressure purposes.
This first edition cancels and replaces ISO 9764:1989 and ISO 9765:1990, which have been technically
revised.
ISO 10893 consists of the following parts, under the general title Non-destructive testing of steel tubes:
⎯ Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel
tubes for the verification of leaktightness
⎯ Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel
tubes for the detection of imperfections
⎯ Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged
arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections
⎯ Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface
imperfections
⎯ Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of
surface imperfections
⎯ Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections
⎯ Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of
imperfections
⎯ Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar
imperfections
⎯ Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the
manufacture of welded steel tubes
⎯ Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged
arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
⎯ Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of
longitudinal and/or transverse imperfections
⎯ Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except
submerged arc-welded) steel tubes
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 10893-11:2011
---------------------- Page: 12 ----------------------
SIST EN ISO 10893-11:2011
INTERNATIONAL STANDARD ISO 10893-11:2011(E)
Non-destructive testing of steel tubes —
Part 11:
Automated ultrasonic testing of the weld seam of welded steel
tubes for the detection of longitudinal and/or transverse
imperfections
1 Scope
This part of ISO 10893 specifies requirements for the automated ultrasonic shear wave (generated by
conventional or phased array technique) testing of the weld seam of submerged arc-welded (SAW) or electric
resistance and induction-welded (EW) steel tubes.
For SAW tubes, the test covers the detection of imperfections oriented predominantly parallel to or, by
agreement, perpendicular to the weld seam or both.
For EW tubes, the test covers the detection of imperfections oriented predominantly parallel to the weld seam.
In the case of testing on longitudinal imperfections, Lamb wave testing can be applied at the discretion of the
manufacturer.
For the detection of imperfections at the weld seam of EW tubes, full peripheral ultrasonic testing is possible.
This part of ISO 10893 can also be applicable to the testing of circular hollow sections.
NOTE For full peripheral ultrasonic testing of seamless and welded (except SAW) tubes, see ISO 10893-10.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5577, Non-destructive testing — Ultrasonic inspection — Vocabulary
ISO 9712, Non-destructive testing — Qualification and certification of personnel
ISO 10893-6, Non-destructive testing of steel tubes — Part 6: Radiographic testing of the weld seam of
welded steel tubes for the detection of imperfections
ISO 10893-7, Non-destructive testing of steel tubes — Part 7: Digital radiographic testing of the weld seam of
welded steel tubes for the detection of imperfections
ISO 11484, Steel products — Employer's qualification system for non-destructive testing (NDT) personnel
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 10893-11:2011
ISO 10893-11:2011(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5577 and ISO 11484 and the
following apply.
3.1
reference standard
standard for the calibration of non-destructive testing equipment (e.g. drill holes, notches, recesses)
3.2
reference tube
tube or length of tube containing the reference standard(s)
3.3
reference sample
sample (e.g. segment of tube, plate or strip) containing the reference standard(s)
NOTE Only the term “reference tube” is used in this part of ISO 10893, also covering the term “reference sample”.
3.4
tube
hollow long product open at both ends, of any cross-sectional shape
3.5
welded tube
ttube made by forming a hollow profile from a flat product and welding adjacent edges together. After welding
the tube may be further processed, either hot or cold, into its final dimensions
3.6
electric welded tube
tube made by pressure welding, in a continuous or non-continuous process, in which strip is formed cold into
a hollow profile and the seam weld made by heating the adjacent edges through the resistance to the passage
of high- or low-frequency current, and pressing the edges together
NOTE The electric current can be applied either by direct electrode contact or by induction.
3.7
manufacturer
organization that manufactures products in accordance with the relevant standard(s) and declares the
compliance of the delivered products with all applicable provisions of the relevant standard(s)
3.8
agreement
contractual arrangement between the manufacturer and purchaser at the time of enquiry and order
4 General requirements
4.1 Unless otherwise specified by the product standards or agreed on by the purchaser and manufacturer,
an ultrasonic test shall be carried out on tubes after completion of all the primary production process
operations (rolling, heat treating, cold and hot working, sizing and primary straightening, etc.).
For cold-expanded tubes, the ultrasonic testing of the weld shall be carried ou
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.