SIST EN ISO 24373:2018
(Main)Welding consumables - Solid wires and rods for fusion welding of copper and copper alloys - Classification (ISO 24373:2018)
Welding consumables - Solid wires and rods for fusion welding of copper and copper alloys - Classification (ISO 24373:2018)
This document specifies requirements for classification of solid wires and rods for fusion welding
of copper and copper alloys. The classification of the solid wires and rods is based on their chemical
composition.
Schweißzusätze - Massivdrähte und -stäbe zum Schmelzschweißen von Kupfer und Kupferlegierungen - Einteilung (ISO 24373:2018)
Produits consommables pour le soudage - Fils pleins et baguettes pleines pour le soudage par fusion du cuivre et des alliages de cuivre - Classification (ISO 24373:2018)
Le présent document spécifie les exigences relatives à la classification des fils pleins et des baguettes pleines pour le soudage par fusion du cuivre et des alliages de cuivre. La classification des fils pleins et des baguettes pleines est basée sur leur composition chimique.
Dodajni materiali za varjenje - Masivne žice in palice za talilno varjenje bakra in bakrovih zlitin - Razvrstitev (ISO 24373:2018)
Ta dokument določa zahteve za razvrstitev masivnih žic in palic za talilno varjenje bakra in bakrovih zlitin. Razvrstitev masivnih žic in palic temelji na kemijski sestavi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24373:2018
01-november-2018
1DGRPHãþD
SIST EN ISO 24373:2012
Dodajni materiali za varjenje - Masivne žice in palice za talilno varjenje bakra in
bakrovih zlitin - Razvrstitev (ISO 24373:2018)
Welding consumables - Solid wires and rods for fusion welding of copper and copper
alloys - Classification (ISO 24373:2018)
Schweißzusätze - Massivdrähte und -stäbe zum Schmelzschweißen von Kupfer und
Kupferlegierungen - Einteilung (ISO 24373:2018)
Produits consommables pour le soudage - Fils pleins et baguettes pleines pour le
soudage par fusion du cuivre et des alliages de cuivre - Classification (ISO 24373:2018)
Ta slovenski standard je istoveten z: EN ISO 24373:2018
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
77.120.30 Baker in bakrove zlitine Copper and copper alloys
SIST EN ISO 24373:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24373:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 24373:2018
EN ISO 24373
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 24373:2009
English Version
Welding consumables - Solid wires and rods for fusion
welding of copper and copper alloys - Classification (ISO
24373:2018)
Produits consommables pour le soudage - Fils pleins et Schweißzusätze - Massivdrähte und -stäbe zum
baguettes pleines pour le soudage par fusion du cuivre Schmelzschweißen von Kupfer und Kupferlegierungen
et des alliages de cuivre - Classification (ISO - Einteilung (ISO 24373:2018)
24373:2018)
This European Standard was approved by CEN on 11 September 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24373:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24373:2018
EN ISO 24373:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24373:2018
EN ISO 24373:2018 (E)
European foreword
This document (EN ISO 24373:2018) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 24373:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 24373:2018 has been approved by CEN as EN ISO 24373:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24373:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 24373:2018
INTERNATIONAL ISO
STANDARD 24373
Second edition
2018-08
Welding consumables — Solid wires
and rods for fusion welding of copper
and copper alloys — Classification
Produits consommables pour le soudage — Fils pleins et baguettes
pleines pour le soudage par fusion du cuivre et des alliages de cuivre
— Classification
Reference number
ISO 24373:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 24373:2018
ISO 24373:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24373:2018
ISO 24373:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
5 Symbols . 1
5.1 Symbol for the product form . 1
5.2 Symbol for the chemical composition . 2
6 Mechanical properties of the weld metal . 2
7 Chemical analysis . 2
8 Rounding procedure . 2
9 Retest . 2
10 Technical delivery conditions . 2
11 Designation . 6
Annex A (informative) Corresponding national classifications . 7
Annex B (informative) Process considerations .10
Bibliography .11
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24373:2018
ISO 24373:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 3, Welding consumables.
Any feedback, question or request for official interpretation related to any aspect of this document
should be directed to the Secretariat of ISO/TC 44/SC 3 via your national standards body. A complete
listing of these bodies can be found at www .iso .org/members .html. Official interpretations, where they
exist, are available from this page: https: //committee .iso .org/sites/tc44/home/interpretation .html
This second edition cancels and replaces the first edition (ISO 24373:2008), which has been technically
revised. The main changes compared to the previous edition are as follows:
— a new alloy, CuSn6MnSi, has been added to Table 1;
— chemistries in Table 1 have been updated for a number of alloys;
— wording regarding Z options has been revised in footnote to Table 1;
— an example showing a Z option has been added;
— Clauses 7, 8 and 9 have been updated to reflect agreed text for all ISO/TC 44/SC 3 standards.
iv © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 24373:2018
ISO 24373:2018(E)
Introduction
For copper-welding consumables, there is no unique relationship between the product form (solid wire
or rod) and the welding process used (e.g. gas-shielded metal arc welding, gas tungsten arc welding,
plasma arc or other welding processes). For this reason, the solid wires or rods can be classified on
the basis of any of the product forms and can be used, as appropriate, for more than one of the above
welding processes.
[1]
This document was originally based on EN 14640:2005 .
© ISO 2018 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 24373:2018
---------------------- Page: 12 ----------------------
SIST EN ISO 24373:2018
INTERNATIONAL STANDARD ISO 24373:2018(E)
Welding consumables — Solid wires and rods for fusion
welding of copper and copper alloys — Classification
1 Scope
This document specifies requirements for classification of solid wires and rods for fusion welding
of copper and copper alloys. The classification of the solid wires and rods is based on their chemical
composition.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
product, dimensions, tolerances and markings
ISO 14344, Welding consumables — Procurement of filler materials and fluxes
ISO 80000-1:2009, Quantities and units — Part 1: General
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: availab
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.