SIST ES 202 706-1 V1.7.1:2022
(Main)Environmental Engineering (EE) - Metrics and measurement method for energy efficiency of wireless access network equipment - Part 1: Power consumption - static measurement method
Environmental Engineering (EE) - Metrics and measurement method for energy efficiency of wireless access network equipment - Part 1: Power consumption - static measurement method
The present document version covers base stations with the following radio access technologies:
• GSM.
• WCDMA.
• LTE.
• NR.
The methodology described in the present document is to measure base station static power consumption and RF output
power. Within the present document it is referred to as static measurements.
The results based on "static" measurements provide power and energy consumption figures for BS under static load.
Energy consumption of terminal (end-user) equipment is outside the scope of the present document.
The scope of the present document is not to define target values for the BS power and energy consumption.
The results should only be used to assess and compare the power and energy consumption of complete base stations.
Wide Area Base Stations and Medium Range Base Stations (as defined in ETSI TS 125 104 [2], ETSI TS 136 104 [12],
and ETSI TS 138 104 [15]) are covered in the present document.
Okoljski inženiring (EE) - Metrika in metoda merjenja energijske učinkovitosti opreme brezžičnega dostopovnega omrežja - 1. del: Poraba energije - Statična merilna metoda
Ta različica dokumenta zajema bazne postaje z naslednjimi tehnologijami radijskega dostopa: • GSM, • WCDMA, • LTE, • NR. Metodologija, opisana v tem dokumentu, se uporablja za merjenje porabe statične energije bazne postaje in izhodne moči RF. V tem dokumentu jo imenujemo statične meritve. Rezultati na podlagi »statičnih« meritev zagotavljajo številske vrednosti moči in porabe energije bazne postaje pri statični obremenitvi. Poraba energije terminalske opreme (opreme končnih uporabnikov) ne spada na področje uporabe tega dokumenta. Namen tega dokumenta ni določiti ciljnih vrednosti za moč in porabo energije baznih postaj. Rezultate naj bi uporabljali le za ocenjevanje in primerjanje moči ter porabe energije celotnih baznih postaj. Ta dokument zajema prostrane bazne postaje in bazne postaje srednjega dosega (kakor so opredeljene v standardih ETSI TS 125-104 [2], ETSI TS 136-104 [12], in ETSI TS 138-104 [15]).
General Information
Buy Standard
Standards Content (Sample)
ETSI ES 202 706-1 V1.7.1 (2022-08)
ETSI STANDARD
Environmental Engineering (EE);
Metrics and measurement method for energy efficiency
of wireless access network equipment;
Part 1: Power consumption - static measurement method
---------------------- Page: 1 ----------------------
2 ETSI ES 202 706-1 V1.7.1 (2022-08)
Reference
RES/EE-EEPS52
Keywords
energy efficiency, GSM, LTE, NR,
power measurement, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
rule and/or regulation and further, no representation or warranty is made of merchantability or fitness
and/or governmental
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI ES 202 706-1 V1.7.1 (2022-08)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Assessment method . 12
5 Reference configurations and Measurement conditions . 12
5.0 Introduction . 12
5.1 Reference configurations . 12
5.2 Measurement and test equipment requirements . 14
5.2.0 Introduction. 14
5.2.1 BS Configuration . 15
5.2.2 RF output (transmit) power/signal . 15
5.2.3 Environmental conditions . 15
5.2.4 Power supply . 16
6 Static Power Measurement . 16
6.0 Introduction . 16
6.1 Measurement methods . 16
6.1.0 Introduction. 16
6.1.1 Test setup for conducted power measurement . 17
6.1.2 Test setup for radiated power measurement. 18
6.1.3 Power measurement procedure . 19
6.1.4 Power measurement in RF sharing mode . 19
6.1.5 Power measurement of multi-band configurations . 20
6.1.5.0 Introduction . 20
6.1.5.1 Configuration of a multi-band BS . 20
6.1.5.2 Specific configurations for dual band GSM . 20
6.1.5.3 Specific configurations for dual band LTE (LTE-A) . 20
6.1.5.4 Specific configurations for dual band and dual technology . 21
6.2 Uncertainty . 21
7 Calculation results . 21
7.1 Load distribution profile . 21
7.2 Integrated base station . 21
7.2.0 Introduction. 21
7.2.1 Calculation of average power consumption of integrated BS . 22
7.2.2 Calculation of daily energy consumption of integrated BS . 22
7.3 Distributed base station . 22
7.3.0 Introduction. 22
7.3.1 Calculation of average power consumption of distributed BS . 22
7.3.2 Calculation of daily energy consumption of distributed BS . 23
8 Measurement report . 23
Annex A (normative): Test Reports . 24
A.1 General information to be reported . 24
ETSI
---------------------- Page: 3 ----------------------
4 ETSI ES 202 706-1 V1.7.1 (2022-08)
A.2 Static measurement report . 25
Annex B (normative): Reference parameters for GSM/EDGE system . 27
Annex C (normative): Reference parameters for WCDMA/HSDPA system . 29
Annex D (normative): Reference parameters for LTE system . 30
Annex E (normative): Reference parameters for NR system . 34
Annex F (normative): Reference parameters for multi-standard system. 36
Annex G (normative): Uncertainty assessment . 38
G.0 Introduction . 38
G.1 General requirements . 38
G.2 Components contributing to uncertainty . 39
G.2.0 Introduction . 39
G.2.1 Contribution of the measurement system . 39
G.2.1.1 Measurement equipment . 39
G.2.1.2 Attenuators, cables . 39
G.2.2 Contribution of physical parameters. 39
G.2.2.1 Impact of environmental parameters. 39
G.2.3 Variance of device under test . 39
G.3 Uncertainty assessment . 40
G.3.1 Combined and expanded uncertainties . 40
G.3.2 Cross correlation of uncertainty factors . 40
G.3.3 Maximum expanded uncertainty . 40
Annex H (informative): Example assessment . 41
Annex I (informative): Interpolation method . 43
Annex J (informative): Load placement examples . 44
Annex K (informative): Bibliography . 47
History . 48
ETSI
---------------------- Page: 4 ----------------------
5 ETSI ES 202 706-1 V1.7.1 (2022-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This ETSI Standard (ES) has been produced by ETSI Technical Committee Environmental Engineering (EE).
The present document is part 1 of a multi-part deliverable covering the metrics and measurement method for energy
efficiency of wireless access network equipment, as identified below:
ETSI ES 202 706-1: "Power consumption - static measurement method";
ETSI TS 102 706-2: "Energy Efficiency - dynamic measurement method".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Energy efficiency is one of the critical factors of the modern telecommunication systems. The energy consumption of
the access network is the dominating part of the wireless telecom network energy consumption. Therefore the core
network and the service network are not considered in the present document. In the radio access network, the energy
consumption of the Base Station is dominating (depending on technology often also referred to as BTS, NodeB,
eNodeB, gNodeB, etc. and in the present document denoted as BS).
ETSI
---------------------- Page: 5 ----------------------
6 ETSI ES 202 706-1 V1.7.1 (2022-08)
The present document, ETSI ES 202 706-1, defines the measurement method for the evaluation of base station power
consumption and energy consumption with static load:
• Average power consumption of BS equipment under static test conditions: the BS average power consumption
is based on measured BS power consumption data under static condition when the BS is loaded artificially in a
lab for three different loads, low, medium and busy hour under given reference configuration.
• Daily average energy consumption.
ETSI TS 102 706-2 [i.8] defines energy efficiency measurement of the LTE base station with dynamic load, and ETSI
TS 103 786 [i.10] defines energy efficiency measurement of the NR base station with dynamic load.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI ES 202 706-1 V1.7.1 (2022-08)
1 Scope
The present document version covers base stations with the following radio access technologies:
• GSM.
• WCDMA.
• LTE.
• NR.
The methodology described in the present document is to measure base station static power consumption and RF output
power. Within the present document it is referred to as static measurements.
The results based on "static" measurements provide power and energy consumption figures for BS under static load.
Energy consumption of terminal (end-user) equipment is outside the scope of the present document.
The scope of the present document is not to define target values for the BS power and energy consumption.
The results should only be used to assess and compare the power and energy consumption of complete base stations.
Wide Area Base Stations and Medium Range Base Stations (as defined in ETSI TS 125 104 [2], ETSI TS 136 104 [12],
and ETSI TS 138 104 [15]) are covered in the present document.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
[3] ETSI EN 300 132-1: "Environmental Engineering (EE); Power supply interface at the input to
Information and Communication Technology (ICT) equipment; Part 1: Alternating Current (AC)".
[4] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current
(DC)".
[5] Void.
[6] Void.
[7] ETSI TS 125 141: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
conformance testing (FDD) (3GPP TS 25.141)".
[8] Void.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI ES 202 706-1 V1.7.1 (2022-08)
[9] Void.
[10] ETSI TS 136 211: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Physical
channels and modulation (3GPP TS 36.211)".
[11] ETSI TS 136 141: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) conformance testing (3GPP TS 36.141)".
[12] ETSI TS 136 104: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) radio transmission and reception (3GPP TS 36.104)".
[13] Void.
[14] ETSI EN 300 132-3: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 3: Up to 400 V Direct Current
(DC)".
[15] ETSI TS 138 104: "5G; NR; Base Station (BS) radio transmission and reception (3GPP
TS 38.104)".
[16] ETSI TS 138 141-1: "5G; NR; Base Station (BS) conformance testing Part 1: Conducted
conformance testing (3GPP TS 38.141-1)".
[17] ETSI TS 138 141-2: "5G; NR; Base Station (BS) conformance testing Part 2: Radiated
conformance testing (3GPP TS 38.141-2)".
[18] ETSI TS 138 211: "5G; NR; Physical channels and modulation (3GPP TS 38.211)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Void.
[i.2] IEC/ISO Guide 98-3:2008: "Evaluation of measurement data - Guide to the expression of
uncertainty in measurement" 2008 or equivalent GUM:2008/JCGM 100:2008.
[i.3] ETSI TS 145 005: "Digital cellular telecommunications system (Phase 2+) (GSM); GSM/EDGE
Radio transmission and reception (3GPP TS 45.005)".
[i.4] ISO/IEC 17025: "General requirements for the competence of testing and calibration laboratories".
[i.5] ETSI TS 151 021: "Digital cellular telecommunications system (Phase 2+) (GSM); Base Station
System (BSS) equipment specification; Radio aspects (3GPP TS 51.021)".
[i.6] IEC 62018: "Power consumption of information technology equipment - Measurement methods".
NOTE: Equivalent to EN 62018 (produced by CENELEC).
[i.7] Void.
[i.8] ETSI TS 102 706-2: "Environmental Engineering (EE); Metrics and Measurement Method for
Energy Efficiency of Wireless Access Network Equipment; Part 2: Energy Efficiency - dynamic
measurement method".
[i.9] ETSI TR 103 117: "Environmental Engineering (EE); Principles for Mobile Network level energy
efficiency".
ETSI
---------------------- Page: 8 ----------------------
9 ETSI ES 202 706-1 V1.7.1 (2022-08)
[i.10] ETSI TS 103 786: "Environmental Engineering (EE); Measurement method for energy efficiency
of wireless access network equipment; Dynamic energy performance measurement method of 5G
Base Station (BS)".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
Base Station (BS): radio access network component which serves one or more radio cells and interfaces the user
terminal (through air interface) and a wireless network infrastructure
BS test control unit: unit which can be used to control and manage BS locally in a lab
BS type 1-C: NR BS operating at FR1, with a conducted interface (antenna connectors available)
BS type 1-H: NR BS operating at FR1, with both a conducted (TAB connectors) and a radiated interface
BS type 1-O: NR BS operating at FR1, with only a radiated interface (no antenna connectors available)
BS type 2-O: NR BS operating at FR2, with only a radiated interface (no antenna connectors available)
busy hour: period during which occurs the maximum total load in a given 24-hour period
busy hour load: the highest measurement level of radio resource configuration
distributed BS: BS architecture which contains remote radio heads (i.e. RRH) close to antenna element and a central
element connecting BS to network infrastructure
efficiency: relation between the useful output (telecom service, etc.) and energy consumption
energy consumption: integral of power consumption over time
full load: operating mode including all radio resources and 100 % traffic conditions
integrated BS: BS architecture in which all BS elements are located close to each other; for example in one single
cabinet
NOTE: The integrated BS architecture may include Tower Mount Amplifier (TMA) close to antenna.
low load: lowest measurement level of radio resource configuration
medium load: medium measurement level of radio resource configuration
medium range BS: Base Station that is characterized by a rated output power (PRAT) above 24 dBm and less than or
equal to 38 dBm
NOTE 1: According to ETSI TS 136 104 [12], ETSI TS 125 104 [2] and ETSI TS 138 104 [15].
NOTE 2: For BS type 1-O and BS type 2-O specific definitions apply according to ETSI TS 138 104 [15].
multi-band base station: configuration which allows the simultaneous operation on at least two different frequency
bands
power saving feature: software/hardware feature in a BS which contributes to decrease power consumption
radiated interface boundary: reference where the radiated requirements apply for BS type 1-O and 2-O
NOTE: For requirements based on EIRP, the radiated interface boundary is associated to the far-field region.
ETSI
---------------------- Page: 9 ----------------------
10 ETSI ES 202 706-1 V1.7.1 (2022-08)
rated output power: mean power level per carrier that the manufacturer has declared to be available at the antenna
connector
NOTE: For FDD BS, rated output power is the mean power level per carrier that the manufacturer has declared to
be available at the antenna connector. For TDD BS rated output power is the mean power level per carrier
over an active timeslot that the manufacturer has declared to be available at the antenna connector.
site correction factor: scaling factor to scale the BS equipment power consumption for reference site configuration
taking into account different power supply solutions, different cooling solutions and power supply losses
static measurement: power consumption measurement performed with different radio resource configurations with
pre-defined and fixed load levels
transceiver array boundary: conducted interface between the transceiver unit array and the composite antenna for BS
type 1-H
wide area BS: Base Station that is characterized by a Rated output Power (PRAT) greater than 38 dBm
NOTE 1: According to ETSI TS 136 104 [12], ETSI TS 125 104 [2], and ETSI TS 138 104 [15].
NOTE 2: For BS type 1-O and BS type 2-O specific definitions apply according to ETSI TS 138 104 [15].
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AAS Active Antenna System
AAU Active Antenna Unit
AC Alternating Current
BCCH Broadcast Control CHannel
BH Busy Hour
BS Base Station
BSC Base Station Controller
BTS Base Transceiver Station
CA Carrier Aggregation
CATR Compact Antenna Test Range
CCE Control Channel Element
CCH Common CHannel
CCPCH Common Control Physical CHannel
CP Cyclic Prefix
CPICH Common PIlot CHannel
CS Circuit Switched
DC Direct Current
DL DownLink
DPCH Dedicated Physical CHannel
DUT Device Under Test
EDGE Enhanced Datarate GSM Evolution
EIRP Equivalent Isotropically Radiated Power
EPRE Emitted Power per Resource Element
FDD Frequency Division Duplex
F
...
Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
ETSI STANDARD
Environmental Engineering (EE);
Metrics and measurement method for energy efficiency
of wireless access network equipment;
Part 1: Power consumption - static measurement method
---------------------- Page: 1 ----------------------
2 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
Reference
RES/EE-EEPS52
Keywords
energy efficiency, GSM, LTE, NR, power
measurement, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
rule and/or regulation and further, no representation or warranty is made of merchantability or fitness
and/or governmental
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Assessment method . 12
5 Reference configurations and Measurement conditions . 12
5.0 Introduction . 12
5.1 Reference configurations . 12
5.2 Measurement and test equipment requirements . 14
5.2.0 Introduction. 14
5.2.1 BS Configuration . 15
5.2.2 RF output (transmit) power/signal . 15
5.2.3 Environmental conditions . 15
5.2.4 Power supply . 16
6 Static Power Measurement . 16
6.0 Introduction . 16
6.1 Measurement methods . 16
6.1.0 Introduction. 16
6.1.1 Test setup for conducted power measurement . 17
6.1.2 Test setup for radiated power measurement. 18
6.1.3 Power measurement procedure . 19
6.1.4 Power measurement in RF sharing mode . 19
6.1.5 Power measurement of multi-band configurations . 20
6.1.5.0 Introduction . 20
6.1.5.1 Configuration of a multi-band BS . 20
6.1.5.2 Specific configurations for dual band GSM . 20
6.1.5.3 Specific configurations for dual band LTE (LTE-A) . 20
6.1.5.4 Specific configurations for dual band and dual technology . 21
6.2 Uncertainty . 21
7 Calculation results . 21
7.1 Load distribution profile . 21
7.2 Integrated base station . 21
7.2.0 Introduction. 21
7.2.1 Calculation of average power consumption of integrated BS . 22
7.2.2 Calculation of daily energy consumption of integrated BS . 22
7.3 Distributed base station . 22
7.3.0 Introduction. 22
7.3.1 Calculation of average power consumption of distributed BS . 22
7.3.2 Calculation of daily energy consumption of distributed BS . 23
8 Measurement report . 23
Annex A (normative): Test Reports . 24
A.1 General information to be reported . 24
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
A.2 Static measurement report . 25
Annex B (normative): Reference parameters for GSM/EDGE system . 27
Annex C (normative): Reference parameters for WCDMA/HSDPA system . 29
Annex D (normative): Reference parameters for LTE system . 30
Annex E (normative): Reference parameters for NR system . 34
Annex F (normative): Reference parameters for multi-standard system. 36
Annex G (normative): Uncertainty assessment . 38
G.0 Introduction . 38
G.1 General requirements . 38
G.2 Components contributing to uncertainty . 39
G.2.0 Introduction . 39
G.2.1 Contribution of the measurement system . 39
G.2.1.1 Measurement equipment . 39
G.2.1.2 Attenuators, cables . 39
G.2.2 Contribution of physical parameters. 39
G.2.2.1 Impact of environmental parameters. 39
G.2.3 Variance of device under test . 39
G.3 Uncertainty assessment . 40
G.3.1 Combined and expanded uncertainties . 40
G.3.2 Cross correlation of uncertainty factors . 40
G.3.3 Maximum expanded uncertainty . 40
Annex H (informative): Example assessment . 41
Annex I (informative): Interpolation method . 43
Annex J (informative): Load placement examples . 44
Annex K (informative): Bibliography . 47
History . 48
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This final draft ETSI Standard (ES) has been produced by ETSI Technical Committee Environmental Engineering (EE),
and is now submitted for the ETSI standards Membership Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the metrics and measurement method for energy
efficiency of wireless access network equipment, as identified below:
ETSI ES 202 706-1: "Power consumption - static measurement method";
ETSI TS 102 706-2: "Energy Efficiency - dynamic measurement method".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Energy efficiency is one of the critical factors of the modern telecommunication systems. The energy consumption of
the access network is the dominating part of the wireless telecom network energy consumption. Therefore the core
network and the service network are not considered in the present document. In the radio access network, the energy
consumption of the Base Station is dominating (depending on technology often also referred to as BTS, NodeB,
eNodeB, gNodeB, etc. and in the present document denoted as BS).
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
The present document, ETSI ES 202 706-1, defines the measurement method for the evaluation of base station power
consumption and energy consumption with static load:
• Average power consumption of BS equipment under static test conditions: the BS average power consumption
is based on measured BS power consumption data under static condition when the BS is loaded artificially in a
lab for three different loads, low, medium and busy hour under given reference configuration.
• Daily average energy consumption.
ETSI TS 102 706-2 [i.8] defines energy efficiency measurement of the LTE base station with dynamic load, and ETSI
TS 103 786 [i.10] defines energy efficiency measurement of the NR base station with dynamic load.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
1 Scope
The present document version covers base stations with the following radio access technologies:
• GSM.
• WCDMA.
• LTE.
• NR.
The methodology described in the present document is to measure base station static power consumption and RF output
power. Within the present document it is referred to as static measurements.
The results based on "static" measurements provide power and energy consumption figures for BS under static load.
Energy consumption of terminal (end-user) equipment is outside the scope of the present document.
The scope of the present document is not to define target values for the BS power and energy consumption.
The results should only be used to assess and compare the power and energy consumption of complete base stations.
Wide Area Base Stations and Medium Range Base Stations (as defined in ETSI TS 125 104 [2], ETSI TS 136 104 [12],
and ETSI TS 138 104 [15]) are covered in the present document.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
[3] ETSI EN 300 132-1: "Environmental Engineering (EE); Power supply interface at the input to
Information and Communication Technology (ICT) equipment; Part 1: Alternating Current (AC)".
[4] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current
(DC)".
[5] Void.
[6] Void.
[7] ETSI TS 125 141: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
conformance testing (FDD) (3GPP TS 25.141)".
[8] Void.
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
[9] Void.
[10] ETSI TS 136 211: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Physical
channels and modulation (3GPP TS 36.211)".
[11] ETSI TS 136 141: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) conformance testing (3GPP TS 36.141)".
[12] ETSI TS 136 104: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) radio transmission and reception (3GPP TS 36.104)".
[13] Void.
[14] ETSI EN 300 132-3: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 3: Up to 400 V Direct Current
(DC)".
[15] ETSI TS 138 104: "5G; NR; Base Station (BS) radio transmission and reception (3GPP
TS 38.104)".
[16] ETSI TS 138 141-1: "5G; NR; Base Station (BS) conformance testing Part 1: Conducted
conformance testing (3GPP TS 38.141-1)".
[17] ETSI TS 138 141-2: "5G; NR; Base Station (BS) conformance testing Part 2: Radiated
conformance testing (3GPP TS 38.141-2)".
[18] ETSI TS 138 211: "5G; NR; Physical channels and modulation (3GPP TS 38.211)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Void.
[i.2] IEC/ISO Guide 98-3:2008: "Evaluation of measurement data - Guide to the expression of
uncertainty in measurement" 2008 or equivalent GUM:2008/JCGM 100:2008.
[i.3] ETSI TS 145 005: "Digital cellular telecommunications system (Phase 2+) (GSM); GSM/EDGE
Radio transmission and reception (3GPP TS 45.005)".
[i.4] ISO/IEC 17025: "General requirements for the competence of testing and calibration laboratories".
[i.5] ETSI TS 151 021: "Digital cellular telecommunications system (Phase 2+) (GSM); Base Station
System (BSS) equipment specification; Radio aspects (3GPP TS 51.021)".
[i.6] IEC 62018: "Power consumption of information technology equipment - Measurement methods".
NOTE: Equivalent to EN 62018 (produced by CENELEC).
[i.7] Void.
[i.8] ETSI TS 102 706-2: "Environmental Engineering (EE); Metrics and Measurement Method for
Energy Efficiency of Wireless Access Network Equipment; Part 2: Energy Efficiency - dynamic
measurement method".
[i.9] ETSI TR 103 117: "Environmental Engineering (EE); Principles for Mobile Network level energy
efficiency".
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
[i.10] ETSI TS 103 786: "Environmental Engineering (EE); Measurement method for energy efficiency
of wireless access network equipment; Dynamic energy performance measurement method of 5G
Base Station (BS)".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
Base Station (BS): radio access network component which serves one or more radio cells and interfaces the user
terminal (through air interface) and a wireless network infrastructure
BS test control unit: unit which can be used to control and manage BS locally in a lab
BS type 1-C: NR BS operating at FR1, with a conducted interface (antenna connectors available)
BS type 1-H: NR BS operating at FR1, with both a conducted (TAB connectors) and a radiated interface
BS type 1-O: NR BS operating at FR1, with only a radiated interface (no antenna connectors available)
BS type 2-O: NR BS operating at FR2, with only a radiated interface (no antenna connectors available)
busy hour: period during which occurs the maximum total load in a given 24-hour period
busy hour load: the highest measurement level of radio resource configuration
distributed BS: BS architecture which contains remote radio heads (i.e. RRH) close to antenna element and a central
element connecting BS to network infrastructure
efficiency: relation between the useful output (telecom service, etc.) and energy consumption
energy consumption: integral of power consumption over time
full load: operating mode including all radio resources and 100 % traffic conditions
integrated BS: BS architecture in which all BS elements are located close to each other; for example in one single
cabinet
NOTE: The integrated BS architecture may include Tower Mount Amplifier (TMA) close to antenna.
low load: lowest measurement level of radio resource configuration
medium load: medium measurement level of radio resource configuration
medium range BS: Base Station that is characterized by a rated output power (PRAT) above 24 dBm and less than or
equal to 38 dBm
NOTE 1: According to ETSI TS 136 104 [12], ETSI TS 125 104 [2] and ETSI TS 138 104 [15].
NOTE 2: For BS type 1-O and BS type 2-O specific definitions apply according to ETSI TS 138 104 [15].
multi-band base station: configuration which allows the simultaneous operation on at least two different frequency
bands
power saving feature: software/hardware feature in a BS which contributes to decrease power consumption
radiated interface boundary: reference where the radiated requirements apply for BS type 1-O and 2-O
NOTE: For requirements based on EIRP, the radiated interface boundary is associated to the far-field region.
ETSI
---------------------- Page: 9 ----------------------
10 Final draft ETSI ES 202 706-1 V1.7.0 (2022-06)
rated output power: mean power level per carrier that the manufacturer has declared to be available at the antenna
connector
NOTE: For FDD BS, rated output power is the mean power level per carrier that the manufacturer has declared to
be available at the antenna connector. For TDD BS rated output power is the mean power level per carrier
over an active timeslot that the manufacturer has declared to be available at the antenna connector.
site correction factor: scaling factor to scale the BS equipment power consumption for reference site configuration
taking into account different power supply solutions, different cooling solutions and power supply losses
static measurement: power consumption measurement performed with different radio resource configurations with
pre-defined and fixed load levels
transceiver array boundary: conducted interface between the transceiver unit array and the composite antenna for BS
type 1-H
wide area BS: Base Station that is characterized by a rated output power (PRAT) greater than 38 dBm
NOTE 1: According to ETSI TS 136 104 [12], ETSI TS 125 104 [2], and ETSI TS 138 104 [15].
NOTE 2: For BS type 1-O and BS type 2-O specific definitions apply according to ETSI TS 138 104 [15].
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AAS Active Antenna System
AAU Active Antenna Unit
AC Alternating Current
BCCH Broadcast Control CHannel
BH Busy Hour
BS Base Station
BSC Base Station Controller
BTS Base Transceiver Station
CA Carrier Aggregation
CATR Compact Antenna Test Range
CCE Control Channel Element
CCH Common CHannel
CCPCH Common Control Physical CHannel
CP Cyclic Prefix
CPICH Common PIlot CHannel
CS Circuit Switched
DC Direct Current
DL DownLi
...
SLOVENSKI STANDARD
SIST ES 202 706-1 V1.7.1:2022
01-oktober-2022
Okoljski inženiring (EE) - Metrika in metoda merjenja energijske učinkovitosti
opreme brezžičnega dostopovnega omrežja - 1. del: Poraba energije - Statična
merilna metoda
Environmental Engineering (EE) - Metrics and measurement method for energy
efficiency of wireless access network equipment - Part 1: Power consumption - static
measurement method
Ta slovenski standard je istoveten z: ETSI ES 202 706-1 V1.7.1 (2022-08)
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
27.015 Energijska učinkovitost. Energy efficiency. Energy
Ohranjanje energije na conservation in general
splošno
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
SIST ES 202 706-1 V1.7.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ES 202 706-1 V1.7.1:2022
---------------------- Page: 2 ----------------------
SIST ES 202 706-1 V1.7.1:2022
ETSI ES 202 706-1 V1.7.1 (2022-08)
ETSI STANDARD
Environmental Engineering (EE);
Metrics and measurement method for energy efficiency
of wireless access network equipment;
Part 1: Power consumption - static measurement method
---------------------- Page: 3 ----------------------
SIST ES 202 706-1 V1.7.1:2022
2 ETSI ES 202 706-1 V1.7.1 (2022-08)
Reference
RES/EE-EEPS52
Keywords
energy efficiency, GSM, LTE, NR,
power measurement, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
rule and/or regulation and further, no representation or warranty is made of merchantability or fitness
and/or governmental
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST ES 202 706-1 V1.7.1:2022
3 ETSI ES 202 706-1 V1.7.1 (2022-08)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Assessment method . 12
5 Reference configurations and Measurement conditions . 12
5.0 Introduction . 12
5.1 Reference configurations . 12
5.2 Measurement and test equipment requirements . 14
5.2.0 Introduction. 14
5.2.1 BS Configuration . 15
5.2.2 RF output (transmit) power/signal . 15
5.2.3 Environmental conditions . 15
5.2.4 Power supply . 16
6 Static Power Measurement . 16
6.0 Introduction . 16
6.1 Measurement methods . 16
6.1.0 Introduction. 16
6.1.1 Test setup for conducted power measurement . 17
6.1.2 Test setup for radiated power measurement. 18
6.1.3 Power measurement procedure . 19
6.1.4 Power measurement in RF sharing mode . 19
6.1.5 Power measurement of multi-band configurations . 20
6.1.5.0 Introduction . 20
6.1.5.1 Configuration of a multi-band BS . 20
6.1.5.2 Specific configurations for dual band GSM . 20
6.1.5.3 Specific configurations for dual band LTE (LTE-A) . 20
6.1.5.4 Specific configurations for dual band and dual technology . 21
6.2 Uncertainty . 21
7 Calculation results . 21
7.1 Load distribution profile . 21
7.2 Integrated base station . 21
7.2.0 Introduction. 21
7.2.1 Calculation of average power consumption of integrated BS . 22
7.2.2 Calculation of daily energy consumption of integrated BS . 22
7.3 Distributed base station . 22
7.3.0 Introduction. 22
7.3.1 Calculation of average power consumption of distributed BS . 22
7.3.2 Calculation of daily energy consumption of distributed BS . 23
8 Measurement report . 23
Annex A (normative): Test Reports . 24
A.1 General information to be reported . 24
ETSI
---------------------- Page: 5 ----------------------
SIST ES 202 706-1 V1.7.1:2022
4 ETSI ES 202 706-1 V1.7.1 (2022-08)
A.2 Static measurement report . 25
Annex B (normative): Reference parameters for GSM/EDGE system . 27
Annex C (normative): Reference parameters for WCDMA/HSDPA system . 29
Annex D (normative): Reference parameters for LTE system . 30
Annex E (normative): Reference parameters for NR system . 34
Annex F (normative): Reference parameters for multi-standard system. 36
Annex G (normative): Uncertainty assessment . 38
G.0 Introduction . 38
G.1 General requirements . 38
G.2 Components contributing to uncertainty . 39
G.2.0 Introduction . 39
G.2.1 Contribution of the measurement system . 39
G.2.1.1 Measurement equipment . 39
G.2.1.2 Attenuators, cables . 39
G.2.2 Contribution of physical parameters. 39
G.2.2.1 Impact of environmental parameters. 39
G.2.3 Variance of device under test . 39
G.3 Uncertainty assessment . 40
G.3.1 Combined and expanded uncertainties . 40
G.3.2 Cross correlation of uncertainty factors . 40
G.3.3 Maximum expanded uncertainty . 40
Annex H (informative): Example assessment . 41
Annex I (informative): Interpolation method . 43
Annex J (informative): Load placement examples . 44
Annex K (informative): Bibliography . 47
History . 48
ETSI
---------------------- Page: 6 ----------------------
SIST ES 202 706-1 V1.7.1:2022
5 ETSI ES 202 706-1 V1.7.1 (2022-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This ETSI Standard (ES) has been produced by ETSI Technical Committee Environmental Engineering (EE).
The present document is part 1 of a multi-part deliverable covering the metrics and measurement method for energy
efficiency of wireless access network equipment, as identified below:
ETSI ES 202 706-1: "Power consumption - static measurement method";
ETSI TS 102 706-2: "Energy Efficiency - dynamic measurement method".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
Energy efficiency is one of the critical factors of the modern telecommunication systems. The energy consumption of
the access network is the dominating part of the wireless telecom network energy consumption. Therefore the core
network and the service network are not considered in the present document. In the radio access network, the energy
consumption of the Base Station is dominating (depending on technology often also referred to as BTS, NodeB,
eNodeB, gNodeB, etc. and in the present document denoted as BS).
ETSI
---------------------- Page: 7 ----------------------
SIST ES 202 706-1 V1.7.1:2022
6 ETSI ES 202 706-1 V1.7.1 (2022-08)
The present document, ETSI ES 202 706-1, defines the measurement method for the evaluation of base station power
consumption and energy consumption with static load:
• Average power consumption of BS equipment under static test conditions: the BS average power consumption
is based on measured BS power consumption data under static condition when the BS is loaded artificially in a
lab for three different loads, low, medium and busy hour under given reference configuration.
• Daily average energy consumption.
ETSI TS 102 706-2 [i.8] defines energy efficiency measurement of the LTE base station with dynamic load, and ETSI
TS 103 786 [i.10] defines energy efficiency measurement of the NR base station with dynamic load.
ETSI
---------------------- Page: 8 ----------------------
SIST ES 202 706-1 V1.7.1:2022
7 ETSI ES 202 706-1 V1.7.1 (2022-08)
1 Scope
The present document version covers base stations with the following radio access technologies:
• GSM.
• WCDMA.
• LTE.
• NR.
The methodology described in the present document is to measure base station static power consumption and RF output
power. Within the present document it is referred to as static measurements.
The results based on "static" measurements provide power and energy consumption figures for BS under static load.
Energy consumption of terminal (end-user) equipment is outside the scope of the present document.
The scope of the present document is not to define target values for the BS power and energy consumption.
The results should only be used to assess and compare the power and energy consumption of complete base stations.
Wide Area Base Stations and Medium Range Base Stations (as defined in ETSI TS 125 104 [2], ETSI TS 136 104 [12],
and ETSI TS 138 104 [15]) are covered in the present document.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
[3] ETSI EN 300 132-1: "Environmental Engineering (EE); Power supply interface at the input to
Information and Communication Technology (ICT) equipment; Part 1: Alternating Current (AC)".
[4] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current
(DC)".
[5] Void.
[6] Void.
[7] ETSI TS 125 141: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
conformance testing (FDD) (3GPP TS 25.141)".
[8] Void.
ETSI
---------------------- Page: 9 ----------------------
SIST ES 202 706-1 V1.7.1:2022
8 ETSI ES 202 706-1 V1.7.1 (2022-08)
[9] Void.
[10] ETSI TS 136 211: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Physical
channels and modulation (3GPP TS 36.211)".
[11] ETSI TS 136 141: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) conformance testing (3GPP TS 36.141)".
[12] ETSI TS 136 104: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) radio transmission and reception (3GPP TS 36.104)".
[13] Void.
[14] ETSI EN 300 132-3: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 3: Up to 400 V Direct Current
(DC)".
[15] ETSI TS 138 104: "5G; NR; Base Station (BS) radio transmission and reception (3GPP
TS 38.104)".
[16] ETSI TS 138 141-1: "5G; NR; Base Station (BS) conformance testing Part 1: Conducted
conformance testing (3GPP TS 38.141-1)".
[17] ETSI TS 138 141-2: "5G; NR; Base Station (BS) conformance testing Part 2: Radiated
conformance testing (3GPP TS 38.141-2)".
[18] ETSI TS 138 211: "5G; NR; Physical channels and modulation (3GPP TS 38.211)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Void.
[i.2] IEC/ISO Guide 98-3:2008: "Evaluation of measurement data - Guide to the expression of
uncertainty in measurement" 2008 or equivalent GUM:2008/JCGM 100:2008.
[i.3] ETSI TS 145 005: "Digital cellular telecommunications system (Phase 2+) (GSM); GSM/EDGE
Radio transmission and reception (3GPP TS 45.005)".
[i.4] ISO/IEC 17025: "General requirements for the competence of testing and calibration laboratories".
[i.5] ETSI TS 151 021: "Digital cellular telecommunications system (Phase 2+) (GSM); Base Station
System (BSS) equipment specification; Radio aspects (3GPP TS 51.021)".
[i.6] IEC 62018: "Power consumption of information technology equipment - Measurement methods".
NOTE: Equivalent to EN 62018 (produced by CENELEC).
[i.7] Void.
[i.8] ETSI TS 102 706-2: "Environmental Engineering (EE); Metrics and Measurement Method for
Energy Efficiency of Wireless Access Network Equipment; Part 2: Energy Efficiency - dynamic
measurement method".
[i.9] ETSI TR 103 117: "Environmental Engineering (EE); Principles for Mobile Network level energy
efficiency".
ETSI
---------------------- Page: 10 ----------------------
SIST ES 202 706-1 V1.7.1:2022
9 ETSI ES 202 706-1 V1.7.1 (2022-08)
[i.10] ETSI TS 103 786: "Environmental Engineering (EE); Measurement method for energy efficiency
of wireless access network equipment; Dynamic energy performance measurement method of 5G
Base Station (BS)".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
Base Station (BS): radio access network component which serves one or more radio cells and interfaces the user
terminal (through air interface) and a wireless network infrastructure
BS test control unit: unit which can be used to control and manage BS locally in a lab
BS type 1-C: NR BS operating at FR1, with a conducted interface (antenna connectors available)
BS type 1-H: NR BS operating at FR1, with both a conducted (TAB connectors) and a radiated interface
BS type 1-O: NR BS operating at FR1, with only a radiated interface (no antenna connectors available)
BS type 2-O: NR BS operating at FR2, with only a radiated interface (no antenna connectors available)
busy hour: period during which occurs the maximum total load in a given 24-hour period
busy hour load: the highest measurement level of radio resource configuration
distributed BS: BS architecture which contains remote radio heads (i.e. RRH) close to antenna element and a central
element connecting BS to network infrastructure
efficiency: relation between the useful output (telecom service, etc.) and energy consumption
energy consumption: integral of power consumption over time
full load: operating mode including all radio resources and 100 % traffic conditions
integrated BS: BS architecture in which all BS elements are located close to each other; for example in one single
cabinet
NOTE: The integrated BS architecture may include Tower Mount Amplifier (TMA) close to antenna.
low load: lowest measurement level of radio resource configuration
medium load: medium measurement level of radio resource configuration
medium range BS: Base Station that is characterized by a rated output power (PRAT) above 24 dBm and less than or
equal to 38 dBm
NOTE 1: According to ETSI TS 136 104 [12], ETSI TS 125 104 [2] and ETSI TS 138 104 [15].
NOTE 2: For BS type 1-O and BS type 2-O specific definitions apply according to ETSI TS 138 104 [15].
multi-band base station: configuration which allows the simultaneous operation on at least two different frequency
bands
power saving feature: software/hardware feature in a BS which contributes to decrease power consumption
radiated interface boundary: reference where the radiated requirements apply for BS type 1-O and 2-O
NOTE: For requirements based on EIRP, the radiated interface boundary is associated to the far-field region.
ETSI
---------------------- Page: 11 ----------------------
SIST ES 202 706-1 V1.7.1:2022
10 ETSI ES 202 706-1 V1.7.1 (2022-08)
rated output power: mean power level per carrier that the manufacturer has declared to be available at the antenna
connector
NOTE: For FDD BS, rated output power is the mean power level per carrier that the manufacturer has declared to
be available at the antenna connector. For TDD BS rated output power is the mean power level per carrier
over an active timeslot that the manufacturer has declared to be available at the antenna connector.
site correction factor: scaling factor to scale the BS equipment power consumption for reference site configuration
taking into account different power supply solutions,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.