SIST EN 61000-3-3:2014/A1:2019

Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection

This part of IEC 61000 is concerned with the limitation of voltage fluctuations and flicker impressed on the public low-voltage system. It specifies limits of voltage changes which may be produced by an equipment tested under specified conditions and gives guidance on methods of assessment. This part of IEC 61000 is applicable to electrical and electronic equipment having an input current equal to or less than 16 A per phase, intended to be connected to public low-voltage distribution systems of between 220 V and 250 V line to neutral at 50 Hz, and not subject to conditional connection. Equipment which does not comply with the limits of this part of IEC 61000 when tested with the reference impedance Zref of 6.4, and which therefore cannot be declared compliant with this part, may be retested or evaluated to show conformity with IEC 61000-3-11. Part 3-11 is applicable to equipment with rated input current ≤ 75 A per phase and subject to conditional connection. The tests according to this part are type tests. Particular test conditions are given in Annex A and the test circuit is shown in Figure 1.

Elektromagnetische Verträglichkeit (EMV) - Teil 3-3: Grenzwerte - Begrenzung von Spannungsänderungen, Spannungsschwankungen und Flicker in öffentlichen Niederspannungs-Versorgungsnetzen für Geräte mit einem Bemessungsstrom <= 16 A je Leiter, die keiner Sonderanschlussbedingung unterliegen

Compatibilité électromagnétique (CEM) - Partie 3-3: Limites - Limitation des variations de tension, des fluctuations de tension et du papillotement dans les réseaux publics d'alimentation basse tension, pour les matériels ayant un courant assigné <= 16 A par phase et non soumis à un raccordement conditionnel

Elektromagnetna združljivost (EMC) - 3-3. del: Mejne vrednosti - Omejitev vrednosti kolebanja napetosti in flikerja v nizkonapetostnih napajalnih sistemih za opremo z naznačenim tokom do 16 A in ni priključena pod posebnimi pogoji - Dopolnilo A1

Ta del standarda IEC 61000 obravnava omejitev vrednosti kolebanja napetosti in flikerja v javnih nizkonapetostnih napajalnih sistemih. Določa omejitve vrednosti kolebanja napetosti, ki jih lahko proizvede oprema, preizkušena pod določenimi pogoji, in podaja smernice za metode ocenjevanja. Ta del standarda IEC 61000 se uporablja za električno in elektronsko opremo z vhodnim tokom do vključno 16 A na fazo, ki je namenjena za povezavo z javnimi nizkonapetostnimi razdelilnimi sistemi z napetostjo med linijskim in nevtralnim vodnikom od 220 V do 250 V pri 50 Hz ter ni priključena pod posebnimi pogoji. Če opremo, ki ni v skladu z omejitvami tega dela standarda IEC 61000, preskušate z referenčno impedanco Zref 6,4 in je zato ni mogoče razglasiti za skladno s tem delom, jo lahko znova preskusite oziroma ocenite, ali je skladna s standardom IEC 61000-3-11. Del 3-11 se uporablja za opremo z nazivnim vhodnim tokom ≤ 75 A na fazo in je priključena pod posebnimi pogoji. Preskusi po tem delu so tipski preskusi. Posebni preskusni pogoji so navedeni v dodatku A, preskusni krog pa je prikazan na sliki 1.

General Information

• Status: Published
• Publication Date: 15-Oct-2019
• ICS: 33.100.01 - Electromagnetic compatibility in general
• ICS: 33.100.10 - Emission
• Technical Committee: EMC - Electromagnetic compatibility
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 10-Oct-2019
• Due Date: 15-Dec-2019
• Completion Date: 16-Oct-2019
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Mandate: M/490 - Standardisation mandate to the European Standardisation Organisations (ESOs) to support European Smart Grid deployment
• Mandate: M/536 - [C(2015)536] Standardisation request as regards radio equipment in support of Directive 2014/53/EU
• Ref Project: EN 61000-3-3:2013/A1:2019 - Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection

Relations

• Amends: SIST EN 61000-3-3:2014 - Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection
• Effective Date: 01-Nov-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61000-3-3:2014/A1:2019
01-november-2019
Elektromagnetna združljivost (EMC) - 3-3. del: Mejne vrednosti - Omejitev
vrednosti kolebanja napetosti in flikerja v nizkonapetostnih napajalnih sistemih za
opremo z naznačenim tokom do 16 A in ni priključena pod posebnimi pogoji -
Dopolnilo A1
Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes,
voltage fluctuations and flicker in public low-voltage supply systems, for equipment with
rated current <= 16 A per phase and not subject to conditional connection
Elektromagnetische Verträglichkeit (EMV) - Teil 3-3: Grenzwerte - Begrenzung von
Spannungsänderungen, Spannungsschwankungen und Flicker in öffentlichen
Niederspannungs-Versorgungsnetzen für Geräte mit einem Bemessungsstrom <= 16 A
je Leiter, die keiner Sonderanschlussbedingung unterliegen
Compatibilité électromagnétique (CEM) - Partie 3-3: Limites - Limitation des variations
de tension, des fluctuations de tension et du papillotement dans les réseaux publics
d'alimentation basse tension, pour les matériels ayant un courant assigné <= 16 A par
phase et non soumis à un raccordement conditionnel
Ta slovenski standard je istoveten z: EN 61000-3-3:2013/A1:2019
ICS:
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 61000-3-3:2014/A1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 61000-3-3:2014/A1:2019

---------------------- Page: 2 ----------------------
SIST EN 61000-3-3:2014/A1:2019


EUROPEAN STANDARD EN 61000-3-3:2013/A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2019
ICS 33.100.10

English Version
Electromagnetic compatibility (EMC) - Part 3-3: Limits -
Limitation of voltage changes, voltage fluctuations and flicker in
public low-voltage supply systems, for equipment with rated
current <= 16 A per phase and not subject to conditional
connection
(IEC 61000-3-3:2013/A1:2017)
Compatibilité électromagnétique (CEM) - Partie 3-3: Limites Elektromagnetische Verträglichkeit (EMV) - Teil 3-3:
- Limitation des variations de tension, des fluctuations de Grenzwerte - Begrenzung von Spannungsänderungen,
tension et du papillotement dans les réseaux publics Spannungsschwankungen und Flicker in öffentlichen
d'alimentation basse tension, pour les matériels ayant un Niederspannungs-Versorgungsnetzen für Geräte mit einem
courant assigné <= 16 A par phase et non soumis à un Bemessungsstrom <= 16 A je Leiter, die keiner
raccordement conditionnel Sonderanschlussbedingung unterliegen
(IEC 61000-3-3:2013/A1:2017) (IEC 61000-3-3:2013/A1:2017)
This amendment A1 modifies the European Standard EN 61000-3-3:2013; it was approved by CENELEC on 2017-06-22. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61000-3-3:2013/A1:2019 E

---------------------- Page: 3 ----------------------
SIST EN 61000-3-3:2014/A1:2019
EN 61000-3-3:2013/A1:2019 (E)
European foreword
The text of document 77A/952/FDIS, future IEC 61000-3-3:2013/A1, prepared by SC 77A, "EMC — Low-
frequency phenomena", of IEC TC 77, "Electromagnetic compatibility" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61000-3-3:2013/A1:2019.
The following dates are fixed:
• latest date by which the document has (dop) 2020-02-02
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2022-08-02
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directives.
For the relationship with EU Directives see informative Annexes ZZA and ZZB, which are an integral part
of this document.
Endorsement notice
The text of the International Standard IEC 61000-3-3:2013/A1:2017 was approved by CENELEC as a
European Standard without any modification.

2

---------------------- Page: 4 ----------------------
SIST EN 61000-3-3:2014/A1:2019
EN 61000-3-3:2013/A1:2019 (E)
Replace Annex ZA of EN 61000-3-3:2013 by the following one:
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
1
IEC/TR 60725 2005 Consideration of reference impedances and - -
public supply network impedances for use in
determining disturbance characteristics of
electrical equipment having a rated current
=< 75 A per phase
1
IEC 60974-1 2017 Arc welding equipment - Part 1: Welding - -
power sources
IEC 61000-3-2 Electromagnetic compatibility (EMC) - Part EN 61000-3-2 2014
3-2: Limits - Limits for harmonic current
emissions (equipment input current ≤ 16 A
per phase)
1
IEC 61000-3-11 2017 Electromagnetic compatibility (EMC) – Part - -
3-11: Limits – Limitation of voltage changes,
voltage fluctuations and flicker in public low-
voltage supply systems – Equipment with
rated current ≤ 75 A and subject to
conditional connection
IEC 61000-4-15 2010 Electromagnetic compatibility (EMC) -- Part EN 61000-4-15 2011
4-15: Testing and measurement techniques
- Flickermeter - Functional and design
specifications


1
Dated as no equivalent European Standard exists.

3

---------------------- Page: 5 ----------------------
SIST EN 61000-3-3:2014/A1:2019
EN 61000-3-3:2013/A1:2019 (E)
Annex ZZA
(informative)

Relationship between this European standard and the essential requirements of
Directive 2014/30/EU [2014 OJ L96] aimed to be covered

This European standard has been prepared under the European Commission standardisation request
2
C(2016) 7641 final of 30.11.2016 , ('M/552'), as regards harmonised standards in support of Directive
2014/30/EU relating to electromagnetic compatibility, to provide one voluntary means of conforming to
essential requirements of Directive 2014/30/EU of the European Parliament and of the Council of 26
February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic
compatibility [2014 OJ L96].

Once this standard is cited in the Official Journal of
...