SIST EN ISO 80000-4:2019/oprA1:2024
(Amendment)Quantities and units - Part 4: Mechanics - Amendment 1 (ISO 80000-4:2019/DAmd 1:2024)
Quantities and units - Part 4: Mechanics - Amendment 1 (ISO 80000-4:2019/DAmd 1:2024)
Größen und Einheiten - Teil 4: Mechanik - Änderung 1 (ISO 80000-4:2019/DAmd1:2024)
Grandeurs et unités - Partie 4: Mécanique - Amendement 1 (ISO 80000-4:2019/DAmd1:2024)
Veličine in enote - 4. del: Mehanika - Dopolnilo 1 (ISO 80000-4:2019/DAmd 1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Veličine in enote - 4. del: Mehanika - Dopolnilo 1 (ISO 80000-4:2019/DAmd 1:2024)
Quantities and units - Part 4: Mechanics - Amendment 1 (ISO 80000-4:2019/DAmd
1:2024)
Größen und Einheiten - Teil 4: Mechanik - Änderung 1 (ISO 80000-4:2019/DAmd1:2024)
Grandeurs et unités - Partie 4: Mécanique - Amendement 1 (ISO 80000-
4:2019/DAmd1:2024)
Ta slovenski standard je istoveten z: EN ISO 80000-4:2019/prA1
ICS:
01.060 Veličine in enote Quantities and units
17.020 Meroslovje in merjenje na Metrology and measurement
splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
Amendment
ISO 80000-4:2019/
DAM 1
ISO/TC 12
Quantities and units —
Secretariat: SIS
Part 4:
Voting begins on:
Mechanics
2024-08-12
Voting terminates on:
AMENDMENT 1
2024-11-04
Grandeurs et unités —
Partie 4: Mécanique
AMENDEMENT 1
ICS: 01.060
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO 80000-4:2019/DAM 1:2024(en)
DRAFT
ISO 80000-4:2019/DAM 1:2024(en)
Amendment
ISO 80000-4:2019/
DAM 1
ISO/TC 12
Quantities and units —
Secretariat: SIS
Part 4:
Voting begins on:
Mechanics
Voting terminates on:
AMENDMENT 1
Grandeurs et unités —
Partie 4: Mécanique
AMENDEMENT 1
ICS: 01.060
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.