kSIST FprEN ISO 14732:2025
(Main)Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO/FDIS 14732:2025)
Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO/FDIS 14732:2025)
This document specifies requirements for qualification of welding operators and also weld setters for mechanized and automatic welding.
This document does not apply to personnel exclusively performing loading or unloading of the automatic welding unit.
This document is applicable when qualification testing of welding operators and weld setters is required by the contract or by the application standard.
The requirements for testing of stud welding operators and setters are given in ISO 14555. The qualification and revalidation is in accordance with this document.
One annex deals with functional knowledge. Another annex deals with welding technical knowledge, a third annex outlines the qualification test certificate.
Schweißpersonal - Prüfung von Bedienern und Einrichtern zum mechanischen und automatischen Schweißen von metallischen Werkstoffen (ISO/DIS 14732:2025)
Dieses Dokument legt die Anforderungen für die Qualifizierung von Bedienern und Einrichtern von Schweißeinrichtungen für das mechanische und automatische Schweißen von metallischen Werkstoffen fest.
Dieses Dokument gilt nicht für Personal, das:
keine Schweißparameter kontrolliert oder anpasst;
nicht an der Einrichtung von Schweißausrüstung beteiligt ist.
Die Qualifizierung von Bedienern und Einrichtern von Schweißeinrichtungen für das Rührreibschweißen und das Rührreibpunktschweißen wird in ISO 25239 3 bzw. ISO 18785 3 behandelt.
Personnel en soudage - Épreuve de qualification des opérateurs soudeurs et des régleurs en soudage pour le soudage mécanisé et le soudage automatique des matériaux métalliques (ISO/FDIS 14732:2025)
Ce document spécifie des exigences relatives à la qualification des opérateurs soudeurs et des régleurs en soudage pour le soudage mécanisé et le soudage automatique.
Elle n'est pas applicable au personnel chargé exclusivement du chargement et du déchargement de l'unité de soudage.
Ce document est applicable lorsque l'épreuve de qualification des opérateurs soudeurs et des régleurs en soudage est exigée par le contrat ou par la norme d'application.
Varilno osebje - Preskušanje za kvalifikacijo varilnih operaterjev in pomožnega osebja za popolnoma mehanizirano in avtomatizirano varjenje kovinskih materialov (ISO/FDIS 14732:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 14732:2024
01-september-2024
Varilno osebje - Preskušanje za kvalifikacijo varilnih operaterjev in pomožnega
osebja za popolnoma mehanizirano in avtomatizirano varjenje kovinskih
materialov (ISO/DIS 14732:2024)
Welding personnel - Qualification testing of welding operators and weld setters for
mechanized and automatic welding of metallic materials (ISO/DIS 14732:2024)
Schweißpersonal - Prüfung von Bedienern und Einrichtern zum mechanischen und
automatischen Schweißen von metallischen Werkstoffen (ISO/DIS 14732:2024)
Personnel en soudage - Épreuve de qualification des opérateurs soudeurs et des
régleurs en soudage pour le soudage mécanisé et le soudage automatique des
matériaux métalliques (ISO/DIS 14732:2024)
Ta slovenski standard je istoveten z: prEN ISO 14732
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.160.01 Varjenje, trdo in mehko Welding, brazing and
spajkanje na splošno soldering in general
oSIST prEN ISO 14732:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 14732:2024
oSIST prEN ISO 14732:2024
DRAFT
International
Standard
ISO/DIS 14732.2
ISO/TC 44/SC 11
Welding personnel — Qualification
Secretariat: ANSI
testing of welding operators and
Voting begins on:
weld setters for mechanized and
2024-05-16
automatic welding of metallic
Voting terminates on:
materials
2024-07-11
Personnel en soudage — Épreuve de qualification des opérateurs
soudeurs et des régleurs en soudage pour le soudage mécanisé et
le soudage automatique des matériaux métalliques
ICS: 25.160.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 14732.2:2024(en)
oSIST prEN ISO 14732:2024
DRAFT
ISO/DIS 14732.2:2024(en)
International
Standard
ISO/DIS 14732.2
ISO/TC 44/SC 11
Welding personnel — Qualification
Secretariat: ANSI
testing of welding operators and
Voting begins on:
weld setters for mechanized and
automatic welding of metallic
Voting terminates on:
materials
Personnel en soudage — Épreuve de qualification des opérateurs
soudeurs et des régleurs en soudage pour le soudage mécanisé et
le soudage automatique des matériaux métalliques
ICS: 25.160.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 14732.2:2024(en)
ii
oSIST prEN ISO 14732:2024
ISO/DIS 14732.2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Qualification . 3
4.1 General .3
4.2 Fusion welding .4
4.3 Resistance welding .5
4.4 Arc stud welding .5
5 Variables and range of qualification . 5
5.1 Mechanized welding .5
5.2 Automatic welding .6
6 Period of validity . 6
6.1 Initial qualification .6
6.2 Confirmation of validity .6
6.3 Revalidation of qualification .6
6.4 Revocation of qualification .7
7 Welding operator or weld setter qualification test certificate . 7
8 Documentation . 7
Annex A (normative) Functional knowledge of the welding unit . 8
Annex B (informative) Knowledge of welding technology . 9
Annex C (informative) Qualification test certificate for welding operators or weld setters .13
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU (PED) aimed to be covered .15
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/29/EU (SPVD) aimed to be covered . 19
Bibliography .20
iii
oSIST prEN ISO 14732:2024
ISO/DIS 14732.2:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 11, Qualification requirements for welding and allied processes personnel, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 121, Welding and allied processes, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 14732:2013), which has been technically
revised.
The main changes are as follows:
— to be added after DIS ballot
Any feedback or questions on this document should be directed to the user’s
national standards body. A complete listing of these bodies can be found at
www.iso.org/members.html. Official interpretations of ISO/TC 44 documents, where they exist, are
available from this page: https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
oSIST prEN ISO 14732:2024
ISO/DIS 14732.2:2024(en)
Introduction
This document is intended to provide the basis for the mutual recognition by examining bodies of
qualification related to the competence of welding operators and weld setters in the various fields of
application. Tests are intended to be carried out in accordance with this document unless more severe tests
are specified by the relevant application standard, when these shall be applied.
The welding operator's or weld setter's ability and job knowledge continue to be approved only if the welding
operators or weld setters are working with reasonable continuity on welding work within the extent of
qualification. However, a functional knowledge test is mandatory.
It is presumed that the welding operator or weld setter has received training or has industrial practice
within the range of qualification.
All new qualifications should be in accordance with this document from the date of issue.
At the end of its period of validity, the existing and valid qualification testing of welding operators and weld
setters in accordance with the requirements of a national standard can be revalidated in accordance with
this document. The new range of qualification will be interpreted in accordance with the requirements of
this document.
v
oSIST prEN ISO 14732:2024
-------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.