SIST-TS CEN/TS 15119-1:2018
(Main)Durability of wood and wood-based products - Determination of emissions from preservative treated wood to the environment - Part 1: Wood held in the storage yard after treatment and wooden commodities exposed in Use Class 3 (not covered, not in contact with the ground) - Laboratory method
Durability of wood and wood-based products - Determination of emissions from preservative treated wood to the environment - Part 1: Wood held in the storage yard after treatment and wooden commodities exposed in Use Class 3 (not covered, not in contact with the ground) - Laboratory method
This Technical Specification describes a laboratory method for obtaining water samples from preservative treated wood exposed out of ground contact (wood held in the storage yard after treatment and which has been in conditions designed to simulate outdoor, out of ground contact situations), at increasing time intervals after exposure.
Dauerhaftigkeit von Holz und Holzprodukten - Abschätzung von Emissionen von mit Holzschutzmitteln behandeltem Holz an die Umwelt - Teil 1: Holz auf dem Lagerplatz nach der Behandlung und Holzprodukte in Gebrauchsklasse 3 (nicht abgedeckt, ohne Erdkontakt) - Laborverfahren
Diese Technische Spezifikation beschreibt ein Laborverfahren für die Gewinnung von Wasserproben von mit Holzschutzmitteln behandeltem Holz ohne Erdkontakt (auf dem Lagerplatz gelagertes Holz nach der Behandlung und in Gebrauchsklasse 3), mit Zeitabständen nach der Beanspruchung.
Durabilité du bois et des matériaux à base de bois - Estimation des émissions dans l'environnement du bois traité avec des produits de préservation - Partie 1 : Bois stocké en dépôt après traitement et articles en bois exposés en classe d'emploi 3 (non couverts, non en contact avec le sol) - Méthode de laboratoire
La présente Spécification technique décrit une méthode de laboratoire permettant d’obtenir des échantillons d’eau à partir d’un bois traité avec des produits de préservation et exposé sans aucun contact avec le sol (bois stocké en dépôt après traitement et exposé à des conditions destinées à simuler des situations en extérieur sans aucun contact avec le sol), à des intervalles de temps croissants après exposition.
Trajnost lesa in lesnih izdelkov - Določanje emisij iz zaščitenega lesa v okolje - 1. del: Sveže zaščiten les v skladiščih in leseni izdelki, izpostavljeni 3. razredu uporabe (nepokrito, ni v stiku z zemljo) - Laboratorijska metoda
V tej tehnični specifikaciji je opisana laboratorijska metoda pridobivanja vzorcev vode iz zaščitenega lesa, izpostavljenega stiku zunaj tal (les, hranjen v skladišču po obdelavi, ki je bil v pogojih, zasnovanih tako, da bi simulirali pogoje na prostem, zunaj tal) pri naraščajočih časovnih intervalih po izpostavljenosti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15119-1:2018
01-marec-2018
1DGRPHãþD
SIST-TS CEN/TS 15119-1:2008
7UDMQRVWOHVDLQOHVQLKL]GHONRY'RORþDQMHHPLVLML]]DãþLWHQHJDOHVDYRNROMH
GHO 6YHåH]DãþLWHQOHVYVNODGLãþLKLQOHVHQLL]GHONLL]SRVWDYOMHQLUD]UHGX
XSRUDEH QHSRNULWRQLYVWLNX]]HPOMR /DERUDWRULMVNDPHWRGD
Durability of wood and wood-based products - Determination of emissions from
preservative treated wood to the environment - Part 1: Wood held in the storage yard
after treatment and wooden commodities exposed in Use Class 3 (not covered, not in
contact with the ground) - Laboratory method
Dauerhaftigkeit von Holz und Holzprodukten - Abschätzung von Emissionen von mit
Holzschutzmitteln behandeltem Holz an die Umwelt - Teil 1: Holz auf dem Lagerplatz
nach der Behandlung und Holzprodukte in Gebrauchsklasse 3 (nicht abgedeckt, ohne
Erdkontakt) - Laborverfahren
Durabilité du bois et des matériaux à base de bois - Estimation des émissions dans
l'environnement du bois traité avec des produits de préservation - Partie 1 : Bois stocké
en dépôt après traitement et articles en bois exposés en classe d'emploi 3 (non couverts,
non en contact avec le sol) - Méthode de laboratoire
Ta slovenski standard je istoveten z: CEN/TS 15119-1:2018
ICS:
13.020.30 Ocenjevanje vpliva na okolje Environmental impact
assessment
71.100.50 .HPLNDOLMH]D]DãþLWROHVD Wood-protecting chemicals
79.040 Les, hlodovina in žagan les Wood, sawlogs and sawn
timber
SIST-TS CEN/TS 15119-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 15119-1:2018
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
January 2018
TECHNISCHE SPEZIFIKATION
ICS 13.020.30; 71.100.50 Supersedes CEN/TS 15119-1:2008
English Version
Durability of wood and wood-based products -
Determination of emissions from preservative treated
wood to the environment - Part 1: Wood held in the
storage yard after treatment and wooden commodities
exposed in Use Class 3 (not covered, not in contact with
the ground) - Laboratory method
Durabilité du bois et des matériaux à base de bois - Dauerhaftigkeit von Holz und Holzprodukten -
Estimation des émissions dans l'environnement du Abschätzung von Emissionen von mit
bois traité avec des produits de préservation - Partie 1 Holzschutzmitteln behandeltem Holz an die Umwelt -
: Bois stocké en dépôt après traitement et articles en Teil 1: Holz auf dem Lagerplatz nach der Behandlung
bois exposés en classe d'emploi 3 (non couverts, non und Holzprodukte in Gebrauchsklasse 3 (nicht
en contact avec le sol) - Méthode de laboratoire abgedeckt, ohne Erdkontakt) - Laborverfahren
This Technical Specification (CEN/TS) was approved by CEN on 21 November 2017 for provisional application.
This Technical Specification was corrected and reissued by the CEN-CENELEC Management Centre on 2018-01-31.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15119-1:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1:2018 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Description of the test method . 5
4 Test report .12
Annex A (informative) Recording forms .13
Bibliography .16
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1:2018 (E)
European foreword
This document (CEN/TS 15119-1:2018) has been prepared by Technical Committee CEN/TC 38
“Durability of wood and wood-based products”, the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 15119-1:2008.
CEN/TS 15119 is composed of the following parts:
— Part 1: Wood held in the storage yard after treatment and wooden commodities exposed in Use Class 3
(not covered, not in contact with the ground) — Laboratory method
— Part 2: Wooden commodities exposed in Use Class 4 or 5 (in contact with the ground, fresh water or sea
water) — Laboratory method
This document is a revision of the Technical Specification published in 2008 in order to consider the
OECD 107 (see Bibliography) which covers the same topic.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1:2018 (E)
Introduction
The emissions from preservative treated wood into the environment need to be quantified to enable an
environmental risk assessment to be made of the treated wood. This document describes a laboratory
method for the determination of emissions by leaching from preservative treated wood where the
preservative treated wood is not covered and not in contact with the ground or the water. There are two
situations in this case where such emissions could enter the environment:
a) Emissions from preservative treated wood stored outside in the storage yard of a preservative
treatment site. Rain falling on the treated wood could produce emissions that run off into surface
water and / or soil;
b) Emissions from treated wood used in commodities exposed in Use Class 3. This is the situation in
which the wood or wood-based product is not covered and not in contact with the ground. It is either
continually exposed to the weather or is protected from the weather but subject to frequent wetting.
Use classes are defined in EN 335 and categorise the biological hazard to which the treated
commodity will be subjected. The Use Classes also define the situation in which the treated
commodity is used and determine the environmental compartments (air, water, soil) which are
potentially at risk from the preservative treated wood. Rain falling on treated wood in Use Class 3
could produce emissions that run off into surface water and/ or soil.
The method is a laboratory procedure for obtaining water samples (leachate) from treated wood exposed
out of ground contact, at time intervals after exposure. The quantities of emissions in the leachate are
related to the surface area of the wood and the length of exposure, to estimate a flux in milligrams per
square metre per day. The flux after increasing periods of exposure (e.g. 1 year, 10 years) can be
estimated.
NOTE The leachate can also be tested for eco-toxicological effects.
The quantity of emissions can be used in an environmental risk assessment of the treated wood.
The test can be applied to wood treated using a penetrating process or superficial application (brush,
spray or dipping), or to treated wood which has an additional surface treatment (e.g., paint that is applied
as a requirement for commercial use).
4
---------------------- Page: 6 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1:2018 (E)
1 Scope
This Technical Specification describes a laboratory method for obtaining water samples from
preservative treated wood exposed out of ground contact (wood held in the storage yard after treatment
and which has been in conditions designed to simulate outdoor, out of ground contact situations), at
increasing time intervals after exposure.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 5667-3, Water quality — Sampling — Part 3: Preservation and handling of water samples (ISO
5667-3)
3 Description of the test method
3.1 General considerations
The principal agent for causing emissions from wood during open-air storage in the yard and in Use Class
3 is rainfall. Wood exposed in above ground situations is subjected to intermittent wetting by rainfall and
drying of the wood surface between the rainfall events. These wetting and drying cycles are simulated by
the method described in this document. It is assumed that emissions obtained by short-term immersion
in water are indicative of the emissions which will occur during exposure to rainfall.
The wood, in the case of wood treated with a wood preservative, shall be representative of commercially
treated wood. It shall be treated in accordance with the preservative manufacturer’s instructions and in
compliance with appropriate standards and specifications. The parameters for post-treatment
conditioning of the wood prior to the commencement of the test shall be stated.
The wood samples used shall be representative of the commodities used.
The composition, amount, pH value and the physical form of rainfall are important in determining the
quantity, content and nature of emissions from wood. However, simulating a realistic rainfall regime in
the laboratory is time-consuming, expensive and is likely to lack reproducibility, accuracy, precision and
reliability.
Two main immersion regimes are recommended as follows:
1. The 3 x 1 minute immersion regime: A 1 minute immersion in water of the treated test specimens to
simulate exposure to a rainfall event. There are three immersions or rainfall events per day, with test
specimens allowed to dry for 3 hours between immersions simulating the wetting and drying cycle
of natural exposure situations. The days of rainfall are set for 1, 3, 5, 8, 10, 12, 15, 17 and 19 days.
NOTE 1 The OECD Emission Scenarios for Wood Preservatives 2013 (see bibliography) that are applied for
the authorization procedure of the European BPR are based on the assumptions, that the total amount of
rainfall per year is 700 mm. The daily regime is intended to produce the same moisture content on the surface
of the wood, and the same moisture content profile in the wood, and thus the same emission, as wood in a real
exposure situation on a day during which rain occurs. It is intended that a 3 x 1 minute dip, every third day,
will give the same moisture content cycle in the wood, and the same emission from the wood, as exposure
under real conditions. If the dipping and drying regime is continued for one year, the emission quantity and
rate would be the same as the emission obtained from wood after exposure in a real situation in a region of
Europe where there is 700 mm of rain per year, with rain events occurring on 260 days of the year.
5
---------------------- Page: 7 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1:2018 (E)
2. The 2 x 1 hour immersion regime: A 1 hour immersion in water of the treated test specimens to
simulate exposure to a rainfall event. There are two immersions or rainfall events per day, with test
specimens allowed to dry for 4 hours between immersions simulating the wetting and drying cycle
of vertical natural exposure situations. The days of rainfall are set for 1, 3, 5, 8, 10, 12, 15, 17 and 19
days.
The applicant must provide adequate discussion of the conditions of these regimes (e.g., purpose is to
estimate emissions from wood that is treated and then exposed vertically or horizontally) for data to be
acceptable when using these regimes.
NOTE 2 The OECD 107 (see in Bibliography) proposes a third immersion regime (1 x 2 hours). It was decided
not to retain this option in the European standard.
3.2 Principle
To simulate the emission of wood preservatives from wood exposed to rain water, a simulated wetting
and drying process is employed. This process is used to simulate the wetting and drying of natural
exposure situations. The water (leachate) from each immersion day is collected and analysed chemically.
It is suitable for ecotoxicity testing. Emission rates in milligrams per square metre per day are calculated
from analytical results.
A system with untreated wood specimens provides background levels for leachates from wood. Tests
with untreated samples can be discontinued if there is no background detected in the first three data
points.
3.3 Quality criteria
3.3.1 Accuracy
The performance of the analytical method should be determined before conducting the test:
1) Accuracy;
2) Specificity;
3) Limit of detection;
4) Limit of quantification.
The testing is carried out with untreated references and with controlled water.
NOTE EN ISO 5667-3 may give guidance on the preservation and handling of water samples.
3.3.2 Reproducibility
Two water samples are collected and analysed and the mean value is taken as the emission value. The
reproducibility of the results within one laboratory and between different laboratories depends upon the
immersion regime and the wood used as test specimens.
3.4 Product and reagent
3.4.1 Water
Water complying with grade 3 of EN ISO 3696 or water especially designed for environmental
investigations is ideal. Deionised water can also be used. The pH value shall normally be in the range 5 to
7. The pH value shall not be adjusted unless special conditions might justify setting the pH to a specified
value between 5 and 7.
6
---------------------- Page: 8 ----------------------
SIST-TS CEN/TS 15119-1:2018
CEN/TS 15119-1:2018 (E)
Water temperature shall be (20 ± 2) °C.
The pH value and water temperature shall be stated in the test report.
3.4.2 Preservative
The identity of the preservative product used to treat the wood samples shall be stated in the test report.
It shall state the name and other designation of the preservative, and the trade or common name of the
active ingredient(s) and substances of concern (as defined in the Biocidal Products Regulation
No.528/2012) or a generic description of co-formulants and the composition of the product expressed in
terms of the mass fraction of each of the ingredients.
3.5 Apparatus
3.5.1 Immersion container
The container shall be made of a material that is inert to water, treated wood and any substance that is
to be determined (glass or plastic may be suitable), and large enough to allow the test specimens to have
all their faces exposed to water and to contain sufficient water for the ratio of the exposed surface area
2 3 2
of the test specimen to the volume of water to which it is exposed, to be 40 (i.e. 40 m per 1m or 0,4 cm
3 2
per 1cm ). The volume of water required is therefore 25 l per m of exposed surface area of the test
3 2
specimen (this is equivalent to 2,5 cm per cm ). The container is covered to avoid any evaporation.
NOTE For example, for five wood test specimens 25 mm wide by 50 mm long, 15 mm thick, end sealed, where
2
the surface area exposed to water is 200 cm , the volume of water required is 500 ml.
3.5.2 Assembly for test specimens
No equipment used to hold the test specimens below the level of the water shall be made of a material
that will react with the water or the treated wood. The test samples should be restrained in a test frame
which allows all 5 test specimens to be manoeuvred simultaneously and which allows free access of water
to all surfaces.
3.5.3 Vessel for receiving water
Laboratory glass flask or plastic jars, inert to water, treated wood and any substance that is to be
determined.
NOTE EN ISO 5667-3 gives the good practices to preserve water samples.
The brown glass flask or plastic jars shall be protected from heat and sunlight.
3.5.4 Preservative treatment
Equipment suitable for carrying out vacuum, vacuum-pressure, immersion or surface treatment of
specimens.
3.5.5 Balance
A balance capable of weighing to the nearest 0,1 g.
3.5.6 Safety equipme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.