SIST EN ISO 11116-1:1999

Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1: Specifications (ISO 11116-1:1999)

This International Standard specifies definitions, dimensions and tolerances of a taper screw thread of nominal diameter 17,4 mm (designated 17E), for the connection of valves to medical and industrial gas cylinders. This standard does not cover the connection requirements for: - mechanical tightness; - gas tightness; - capability of repeated assembly and dismounting operations. Gauge inspection is covered in Part 2.

Ortsbewegliche Gasflaschen - Gasflaschen - 17E kegeliges Gewinde zum Anschluß von Ventilen an Gasflaschen (ISO 11116-1:1999)

Dieser Teil von ISO 11116 legt Begriffe, Maße und Toleranzen für kegelige Gewinde mit einem Nenndurchmesser von 17,4 mm (Bezeichnung 17E) für den Anschluß von Ventilen an Gasflaschen für den medizinischen und industriellen Gebrauch fest. Dieser Teil von ISO 11116 enthält keine Anforderungen an die Verbindung hinsichtlich - der mechanischen Festigkeit; - der Gasdichtheit; - der Fähigkeit, eine Reihe von Montagen und Demontagen unbeschadet zu überstehen. Die Lehrenprüfung ist in EN ISO 11116-2 geregelt.

Bouteilles a gaz - Filetage conique 17E pour le raccordement des robinets sur les bouteilles a gaz - Partie 1: Spécifications (ISO 11116-1:1999)

L'IEC 60831-2:2014 est applicable aux condensateurs conformes à la CEI 60831-1, et contient les exigences relatives aux essais de vieillissement, d'autorégénération et de destruction de ces condensateurs. Cette troisième édition annule et remplace la deuxième édition parue en 1995. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- mise à jour des références normatives;
- réalisation des cycles de décharge à température ambiante avant essai de vieillissement;
- réalisation d'un essai d'autorégénération à tension alternative en courant alternatif;
- modification des conditions d'acceptation après la réalisation d'un essai d'autorégénération;
- modification de l'essai de destruction.
Mots clés: CEI 60831-1, exigences relatives aux essais de vieillissement, d'autorégénération et de destruction de condensateurs.

Plinske jeklenke - Konični navoj 17E za povezavo ventila s plinsko jeklenko - 1. del: Specifikacije (ISO 11116-1:1999))

General Information

• Status: Withdrawn
• Publication Date: 31-Aug-1999
• Withdrawal Date: 13-Sep-2010
• ICS: 21.040.30 - Special screw threads
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: TLP - Pressure vessels
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 13-Sep-2010
• Due Date: 06-Oct-2010
• Completion Date: 14-Sep-2010
• Ref Project: EN ISO 11116-1:1999 - Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1: Specifications (ISO 11116-1:1999)

Relations

• Replaced By: SIST EN ISO 11363-1:2010 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2010)
• Effective Date: 01-Nov-2010
• Replaced By: SIST EN ISO 11363-1:2010 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2010)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11116-1:1999
01-september-1999
3OLQVNHMHNOHQNH.RQLþQLQDYRM(]DSRYH]DYRYHQWLODVSOLQVNRMHNOHQNR
GHO6SHFLILNDFLMH,62
Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1:
Specifications (ISO 11116-1:1999)
Ortsbewegliche Gasflaschen - Gasflaschen - 17E kegeliges Gewinde zum Anschluß von
Ventilen an Gasflaschen (ISO 11116-1:1999)
Bouteilles a gaz - Filetage conique 17E pour le raccordement des robinets sur les
bouteilles a gaz - Partie 1: Spécifications (ISO 11116-1:1999)
Ta slovenski standard je istoveten z: EN ISO 11116-1:1999
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST EN ISO 11116-1:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11116-1:1999

---------------------- Page: 2 ----------------------

SIST EN ISO 11116-1:1999

---------------------- Page: 3 ----------------------

SIST EN ISO 11116-1:1999

---------------------- Page: 4 ----------------------

SIST EN ISO 11116-1:1999
INTERNATIONAL ISO
STANDARD 11116-1
First edition
1999-04-01
Gas cylinders — 17E taper thread for
connection of valves to gas cylinders —
Part 1:
Specification
Bouteilles à gaz — Filetages coniques 17E pour le raccordement des
robinets sur les bouteilles à gaz —
Partie 1: Spécifications
A
Reference number
ISO 11116-1:1999(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 11116-1:1999
ISO 11116-1:1999(E)
Contents
Page
1 Scope .1
2 Terms and definitions .1
3 Requirements.3
3.1 Thread rotation.3
3.2 Taper .3
3.3 Thread profile.4
3.4 Pitch, P.4
4 Thread end finish.4
5 Identification.4
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 11116-1:1999
©
ISO
ISO 11116-1:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 11116-1 was prepared by Technical Committee ISO/TC 58, Gas cylinders,
Subcommittee SC 2, Cylinder fittings.
ISO 11116 consists of the following parts, under the general title Gas cylinders — 17E taper thread for connection
of valves to gas cylinders:
 Part 1: Specification
 Part 2: Inspection gauges
iii

---------------------- Page: 7 ----------------------

SIST EN ISO 11116-1:1999
©
ISO 11116-1:1999(E) ISO
Introduction
This part of ISO 11116 belongs to a series of standards specifying thread dimensions and gauge requirements.
Cylinders intended to contain compressed, liquefied or dissolved gas under pressure are fitted with accessories
(valves, straight or angle fittings) to allow release of and refilling with, gas. Hereinafter, the term "valve" will apply to
such accessories.
The connection, between cylinder and valve, is obtained by assembly of two taper threads, an external one on the
valve stem and an internal one in the cylinder neck, each having the same nominal taper, pitch and thread profile.
iv

---------------------- Page: 8 ----------------------

SIST EN ISO 11116-1:1999
INTERNATIONAL STANDARD  © ISO ISO 11116-1:1999(E)
Gas cylinders — 17E taper thread for connection of valves to gas
cylinders —
Part 1:
Specification
1 Scope
This part of ISO 11116 specifies definitions, dimensions and tolerances of a taper screw thread of nominal diameter
17,4 mm (designated 17E), for the connection of valves to medical and
...