iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 16929:2019

(Main)

Test methods - Timber floors - Determination of vibration properties

Test methods - Timber floors - Determination of vibration properties

This Europen Standard specifies test methods for the determination of the fundamental frequency, damping, unit point load deflection and acceleration of timber or wood based composite beams and flooring systems.

Prüfverfahren - Holzdecken - Bestimmung der Schwingungseigenschaften

Méthodes d’essais - Planchers en bois - Détermination des propriétés vibratoires

Le présent document spécifie des méthodes d'essais pour la détermination de la fréquence fondamentale, de l'amortissement, de la flèche sous charge concentrée et de l'accélération des planchers composés de bois scié, de produits transformés à base de bois et de poutres ou dalles en bois massif (par exemple, bois lamellé-croisé CLT, bois lamellé-collé GL, bois lamellé-cloué NLT), avec ou sans chapes en béton, ainsi que des planchers composites bois-béton.

Preskusne metode - Leseni stropi - Ugotavljanje vibracijskih lastnosti

Ta evropski standard določa preskusne metode za ugotavljanje osnovne frekvence, dušenja, upogibanja pod točkovno obremenitvijo in pospeševanja lesenih kompozitnih nosilcev in stropnih sistemov ter kompozitnih nosilcev in stropnih sistemov na osnovi lesa.

General Information

Status
Published
Public Enquiry End Date
29-Jan-2016
Publication Date
12-Feb-2019
ICS
91.060.30 - Ceilings. Floors. Stairs
91.080.20 - Timber structures
Technical Committee
KON.005 - Timber structures
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Jan-2019
Due Date
22-Mar-2019
Completion Date
13-Feb-2019
Ref Project
EN 16929:2018 - Test methods - Timber floors - Determination of vibration properties

Buy Standard

SIST EN 16929:2019SIST EN 16929:2019
PreviousNext
Standard
SIST EN 16929:2019
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Preskusne metode - Leseni stropi - Ugotavljanje vibracijskih lastnostiPrüfverfahren - Holzdecken - Bestimmung der SchwingungseigenschaftenMéthodes d’essais - Planchers en bois - Détermination des propriétés vibratoiresTest methods - Timber floors - Determination of vibration properties91.080.20Lesene konstrukcijeTimber structures91.060.30Stropi. Tla. StopniceCeilings. Floors. StairsICS:Ta slovenski standard je istoveten z:EN 16929:2018SIST EN 16929:2019en,fr,de01-marec-2019SIST EN 16929:2019SLOVENSKI

STANDARD
SIST EN 16929:2019
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16929
December
t r s z ICS
{ sä r x rä u râ
{ sä r z rä t r English Version

Test methods æ Timber floors æ Determination of vibration properties Méthodes d 5essais æ Planchers en bois æ Détermination des propriétés vibratoires

Prüfverfahren æ Holzdecken æ Bestimmung der Schwingungseigenschaften This European Standard was approved by CEN on

{ November
t r s zä

egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä

translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä

CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä

EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels

t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN

s x { t {ã t r s z ESIST EN 16929:2019

EN 16929:2018 (E) 2 Contents Page European foreword ....................................................................................................................................................... 4 Introduction .................................................................................................................................................................... 5 1 Scope .................................................................................................................................................................... 6 2 Normative references .................................................................................................................................... 6 3 Terms and definitions ................................................................................................................................... 6 4 Determination of the dimensions of a floor system ........................................................................... 8 5 Determination of moisture content .......................................................................................................... 9 6 Determination of the floor mass ................................................................................................................ 9 7 Conditioning ...................................................................................................................................................... 9 8 Laboratory testing ....................................................................................................................................... 10 8.1 Determination of the fundamental frequency ................................................................................... 10 8.1.1 Principle .......................................................................................................................................................... 10 8.1.2 Test setup ........................................................................................................................................................ 10 8.1.3 Support detailing .......................................................................................................................................... 10 8.1.4 Test procedure .............................................................................................................................................. 10 8.1.5 Apparatus ........................................................................................................................................................ 11 8.1.6 Results .............................................................................................................................................................. 11 8.2 Determination of damping ratio ............................................................................................................. 11 8.3 Determination of the static unit point load deflection ................................................................... 12 8.3.1 General ............................................................................................................................................................. 12 8.3.2 Test setup ........................................................................................................................................................ 13 8.3.3 Test procedure .............................................................................................................................................. 13 8.3.4 Results .............................................................................................................................................................. 13 8.3.5 Apparatus ........................................................................................................................................................ 13 8.4 Determination of the floor acceleration .............................................................................................. 13 8.4.1 General ............................................................................................................................................................. 13 8.4.2 Test setup ........................................................................................................................................................ 13 8.4.3 Test procedure .............................................................................................................................................. 14 8.4.4 Results .............................................................................................................................................................. 14 8.4.5 Apparatus ........................................................................................................................................................ 14 9 In situ testing ................................................................................................................................................. 14 9.1 Determination of the fundamental frequency ................................................................................... 14 9.1.1 Test setup ........................................................................................................................................................ 14 9.1.2 Test procedure .............................................................................................................................................. 15 9.1.3 Results .............................................................................................................................................................. 15 9.1.4 Apparatus ....................................

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60286-2:2023(Main)
Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes (IEC 60286-2:2022)
EN IEC 60286-2:2022

IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant technical changes with respect to the previous edition: a) complete revision of structure; b) consolidation of essential parameters and requirements in Clause 4.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 19101:2023(Main)
Design of fibre-polymer composite structures
CEN/TS 19101:2022

1.1   Scope of FprCEN/TS 19101
(1) This document applies to the design of buildings, bridges and other civil engineering structures in fibre-polymer composite materials, including permanent and temporary structures. It complies with the principles and requirements for the safety, serviceability and durability of structures, the basis of their design and verification that are given in EN 1990.
NOTE   In this document, fibre-polymer composite materials are referred to as composite materials or as composites.
(2) This document is only concerned with the requirements for resistance, serviceability, durability and fire resistance of composite structures.
NOTE 1   Specific requirements concerning seismic design are not considered.
NOTE 2   Other requirements, e.g. concerning thermal or acoustic insulation, are not considered.
(3) This document gives a general basis for the design of composite structures composed of (i) composite members, or (ii) combinations of composite members and members of other materials (hybrid-composite structures), and (iii) the joints between these members.
(4) This document applies to composite structures in which the values of material temperature in members, joints and components in service conditions are (i) higher than -40 °C and (ii) lower than   - 20 °C, where   is the glass transition temperature of composite, core and adhesive materials, defined according to 5.1(1).
(5) This document applies to:
(i) composite members, i.e. profiles and sandwich panels, and
(ii) bolted, bonded and hybrid joints and their connections.
NOTE 1   Profiles and sandwich panels can be applied in structural systems such as beams, columns, frames, trusses, slabs, plates and shells.
NOTE 2   Sandwich panels include homogenous core and web-core panels. In web-core panels, the cells between webs can be filled (e.g. with foam) or remain empty (e.g. panels from pultruded profiles).
NOTE 3   This document does not apply to sandwich panels made of metallic face sheets.
NOTE 4   Built-up members can result from the assembly of two or more profiles, through bolting and/or adhesive bonding.
NOTE 5   The main manufacturing processes of composite members include pultrusion, filament winding, hand layup, resin transfer moulding (RTM), resin infusion moulding (RIM), vacuum-assisted resin transfer moulding (VARTM).
NOTE 6   This document does not apply to composite cables or special types of civil engineering works (e.g. pressure vessels, tanks or chemical storage containers).
(6) This document applies to:
(i) the composite components of composite members, i.e. composite plies, composite laminates, sandwich cores and plates or profiles, and
(ii) the components of joints or their connections, i.e. connection plates or profiles (e.g. cleats), bolts, and adhesive layers.
NOTE 1   Composite components are composed of composite materials (i.e. fibres and matrix resins) and core materials. Components of joints and their connections are also composed of composite, steel or adhesive materials.
NOTE 2   The fibre architecture of composite components can comprise a single type of fibres or a hybrid of two or more types of fibres.
NOTE 3   This document does not apply to composite components used for internal reinforcement of concrete structures (composite rebars) or strengthening of existing structures (composite rebars, strips or sheets).
(7) This document applies to composite materials, comprising:
(i) glass, carbon, basalt or aramid fibres, and
(ii) a matrix based on unsaturated polyester, vinylester, epoxy or phenolic thermoset resins.

  • Technical specification
    238 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    238 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50600-4-8:2023(Main)
Information technology - Data centre facilities and infrastructures - Part 4-8: Carbon usage effectiveness
EN 50600-4-8:2022

This document specifies the Carbon Usage Effectiveness (CUE) as a KPI to qualify the CO2 emissions of a data centre during use phase of the data centre life cycle. By reporting CO2 emissions, it is possible to present the data centres contribution to climate change (enhanced greenhouse effect).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-1:2023(Main)
Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings
EN 1993-1-1:2022

1.1   Scope of EN 1993 1 1
(1) EN 1993 1 1 gives basic design rules for steel structures.
(2) It also gives supplementary provisions for the structural design of steel buildings. These supplementary provisions are indicated by the letter "B" after the paragraph number, thus (  )B.
1.2   Assumptions
(1) The assumptions of EN 1990 apply to EN 1993 1 1.
(2) EN 1993 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), the parts of EN 1992 to EN 1999 where steel structures or steel components are referred to within those documents, EN 1090 2, EN 1090 4 and ENs, EADs and ETAs for construction products relevant to steel structures.

  • Standard
    120 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    118 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 22753:2023(Main)
Molecular biomarker analysis - Method for the statistical evaluation of analytical results obtained in testing sub-sampled groups of genetically modified seeds and grains - General requirements (ISO 22753:2021, Corrected version 2022-11)
EN ISO 22753:2022

This document describes general requirements, procedures and performance criteria for evaluating the content of genetically modified (GM) seeds/grains in a lot by a group testing strategy that includes qualitative analysis of sub-sampled groups followed by statistical evaluation of the results.
This document is applicable to group testing strategy estimating the GM content on a percentage seed/grain basis for purity estimation, testing towards a given reject/accept criterion and for cases where seed/grain lots are carrying stacked events.
This document is not applicable to processed products.
NOTE       Description of the use of group testing strategy are available in References [1], [7], [8], [18], [19] and [20].

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1993-1-101:2023(Main)
Eurocode 3: Design of steel structures - Part 1-101: Alternative interaction method for members in bending and compression
CEN/TS 1993-1-101:2022

(1) This document provides an alternative method for the stability verification of steel members under compression axial force and bending moment, with reference to EN 1993 1 1.
NOTE   For the applicability of this document, see Clause 4.
(2) The method given in this document applies to uniform steel members with double symmetric cross-section under axial compression force and bi-axial bending.

  • Technical specification
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16923:2023(Main)
Foodstuffs - Determination of T-2 toxin and HT-2 toxin in cereals and cereal products for infants and young children by SPE clean up and HPLC-MS/MS
EN 16923:2022

This document describes a method for the determination of T-2 toxin and HT-2 toxin in cereals and cereal-based products, e.g. oats, intended for nutrition of infants and young children by high performance liquid chromatography (HPLC) coupled with tandem mass spectrometry (MS/MS) after cleanup by solid phase extraction (SPE) [5].
The method has been validated for HT-2 toxin in oat flour at levels of 9,3 µg/kg and 28,1 µg/kg, oat flakes at levels of 16,5 µg/kg and 21,4 µg/kg, and breakfast cereals (containing oat flakes) at a level of 8,1 µg/kg and for T-2 toxin in oat flour at levels of 4,4 µg/kg and 8,3 µg/kg, oat flakes at levels of 4,9 µg/kg and 6,6 µg/kg and breakfast cereals (containing oat flakes) at a level of 3,5 µg/kg.
Laboratory experiences [6] have shown that the method is also applicable to highly swelling materials (dry cereal based porridges and modified starches), but these were not examined in the method validation study. Details are outlined in 7.3.
The method can also be applied to oat-by-products at higher levels of T-2- and HT-2 toxin. In this case, the dilution steps need to be considered [6].
The method can also be applied to cereals and cereal products for infants and young children based on e.g. wheat, barley and rice. In this case, the method needs to be in-house-validated for each material. At the time of the interlaboratory study, planned range was 10 µg/kg to 100 µg/kg, and it is known from the pre-study that the method works well in the whole range, although final validation was only done in the range from 3,5 µg/kg to 28,1 µg/kg.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17686:2023(Main)
Flexible sheets for waterproofing - Determination of the resistance to wind load of roof build-up system with bonded waterproofing systems
EN 17686:2022

This European Standard specifies the test method to determine the resistance to wind load of the roof build-up system with the waterproofing system bonded to the substrate.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8872:2023(Main)
Aluminium caps and aluminium/plastic caps for infusion bottles and injection vials - General requirements and test methods (ISO 8872:2022)
EN ISO 8872:2022

This document specifies general requirements and test methods for aluminium caps and aluminium/plastic caps intended for use on infusion bottles and/or injection vials.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20270:2023(Main)
Acoustics - Characterization of sources of structure-borne sound and vibration - Indirect measurement of blocked forces (ISO 20270:2019)
EN ISO 20270:2022

This document specifies a method where a vibrating component (a source of structure-borne sound or vibration) is attached to a passive structure (or receiver) and is the cause of vibration in, or structure-borne sound radiation from, the assembly. Examples are pumps installed in ships, servo motors in vehicles or machines and plant in buildings. Almost any vibrating component can be considered as a source in this context.
Due to the need to measure vibration at all contact degrees of freedom (DOFs) (connections between the source and receiver), this document can only be applied to assemblies for which such measurement is possible.
This document is applicable only to assemblies whose frequency response functions (FRFs) are linear and time invariant.
The source can be installed into a real assembly or attached to a specially designed test stand (as described in 5.2).
The standard method has been validated for stationary signals such that the results can be presented in the frequency domain. However, the method is not restricted to stationary signals: with appropriate data processing, it is also applicable to time-varying signals such as transients and shocks (provided linearity and time invariance of the FRFs are preserved).
This document provides a method for measurement and presentation of blocked forces, together with guidelines for minimizing uncertainty. It provides a method evaluating the quality of the results through an on-board validation procedure but does not comment on the acceptability or otherwise of the results.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day