Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods

This European Standard specifies requirements and test methods for marketed and delivered ethanol to be used as an extender for automotive fuel for petrol engine vehicles in accordance with the requirements of EN 228.

Kraftstoffe für Kraftfahrzeuge - Ethanol zur Verwendung als Blendkomponente in Ottokraftstoff - Anforderungen und Prüfverfahren

Diese Europäische Norm legt Anforderungen und Prüfverfahren für angeliefertes bzw. vermarktetes Ethanol fest, das als Streckmittel für Kraftstoffe zum Einsatz in Kraftfahrzeugen mit Ottomotor, in Übereinstimmung mit den Anforderungen von EN 228, Verwendung findet. ANMERKUNG 1 Dieses Dokument gibt alle relevanten Kenndaten, Anforderungen und Prüfverfahren für (Bio)Ethanol vor, die zum gegenwärtigen Zeitpunkt für die Festlegung der Produkteigenschaften für den Einsatz als Blendkomponente bis zu einem Volumenanteil von bis zu 10 % (V/V) in Ottokraftstoff als notwendig bekannt sind. Diese Anforderungen bedürfen einer erneuten Untersuchung, sofern der Anteil bzw. die Verwendung einen Volumenanteil von 10 % (V/V) übersteigt. ANMERKUNG 2 Für die Zwecke dieses Dokuments wird zur Angabe des Massenanteils einer Substanz, μ, der Ausdruck „% (m/m)“ und für den Volumenanteil einer Substanz, φ, der Ausdruck „% (V/V)“ verwendet.

Carburants pour automobiles - Ethanol comme base de mélange à l'essence - Exigences et méthodes d'essais

Le présent document prescrit des exigences et des méthodes d’essais pour l’éthanol mis sur le marché et livré pour être utilisé comme composant du carburant automobile pour véhicules à moteur à essence conformément aux exigences de l'EN 228.
NOTE 1   Le présent document donne l’ensemble des caractéristiques, des exigences et méthodes d'essai applicables à l’(au) (bio)éthanol qui sont actuellement reconnues comme nécessaires pour définir le produit destiné à être utilisé en mélange avec l’essence automobiles à hauteur de 10 % (V/V) maximum. Pour une teneur plus élevée ou un usage au-delà de 10 % en volume, les exigences doivent être réétudiées.
NOTE 2   Dans le cadre de ce document, les expressions "% (m/m)" et "% (V/V)" sont utilisées pour désigner respectivement les fractions massiques,µ, et les fractions volumiques, φ.

Goriva za motorna vozila - Etanol kot komponenta za dodajanje motornemu bencinu - Zahteve in preskusne metode

Ta evropski standard določa zahteve za preskusne metode za etanol, ki je na trgu ali se dobavlja in ki se uporablja kot polnilo pri gorivih za motorna vozila, v skladu z zahtevami iz EN 228.

General Information

Status
Withdrawn
Public Enquiry End Date
14-Dec-2009
Publication Date
02-Mar-2011
Withdrawal Date
21-Oct-2014
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
22-Oct-2014
Due Date
14-Nov-2014
Completion Date
22-Oct-2014

Relations

Buy Standard

Standard
EN 15376:2011
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Goriva za motorna vozila - Etanol kot komponenta za dodajanje motornemu bencinu - Zahteve in preskusne metodeKraftstoffe für Kraftfahrzeuge - Ethanol zur Verwendung als Blendkomponente in Ottokraftstoff - Anforderungen und PrüfverfahrenCarburants pour automobiles - Ethanol comme base de mélange à l'essence - Exigences et méthodes d'essaisAutomotive fuels - Ethanol as a blending component for petrol - Requirements and test methods75.160.20Liquid fuels71.080.60Alkoholi. EtriAlcohols. EthersICS:Ta slovenski standard je istoveten z:EN 15376:2011SIST EN 15376:2011en,de01-april-2011SIST EN 15376:2011SLOVENSKI
STANDARDSIST EN 15376:2008+A1:20091DGRPHãþD



SIST EN 15376:2011



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15376
February 2011 ICS 71.080.60; 75.160.20 Supersedes EN 15376:2007+A1:2009English Version
Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods
Carburants pour automobiles - Ethanol comme base de mélange à l'essence - Exigences et méthodes d'essais
Kraftstoffe für Kraftfahrzeuge - Ethanol zur Verwendung als Blendkomponente in Ottokraftstoff - Anforderungen und Prüfverfahren This European Standard was approved by CEN on 24 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15376:2011: ESIST EN 15376:2011



EN 15376:2011 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Sampling .54 Requirements and test methods .54.1 Dyes and markers .54.2 Additives .54.3 Denaturing .54.4 Generally applicable requirements and related test methods .64.5 Climate dependent requirements and related test methods .74.6 Precision and dispute .7Bibliography .8 SIST EN 15376:2011



EN 15376:2011 (E) 3 Foreword This document (EN 15376:2011) has been prepared by Technical Committee CEN/TC 19 “Gaseous and liquid fuels, lubricants and related products of petroleum, synthetic and biological origin”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2011, and conflicting national standards shall be withdrawn at the latest by August 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has originally been prepared under mandate M/344 given to CEN by the European Commission and the European Free Trade Association along with other standards intended to be complementary to the regulatory measures contained in various EU Directives, see [1], [2], [3] and [4]. If bio-ethanol is meant for use as automotive fuel component, this document applies. It is intended to call up this European Standard in EN 228, in order to define the quality of (bio)ethanol which is added/blended to the petrol. This document supersedes EN 15376:2007+A1:2009.
The major updates of this second version concern the inclusion of newly developed methods for determination of appearance and of the content of oxygenates, water, involatile material, sulfate, inorganic chloride, copper and phosphorus. All of these methods were under development at the time of publication of the former version. In addition some alignment on the units in terms of mass/mass has been developed. An electrical conductivity test method has also been developed on the basis of a DIN test method [5] in order to adequately limit the strong acidity and the base alkalinity of the product, which cannot be sufficiently determined via pHe [6]. The former version gave all relevant characteristics, requirements and test methods for (bio)ethanol, which were known at that time to be necessary to define the product to be used up to a maximum 5 % (V/V) blending component for automotive petrol fuel. With the actual document the percentage of use is expanded to allow use at percentages up to 10 % (V/V) and the requirements are updated accordingly. Now that a test method is available a sulfate limit has also been set. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 15376:2011



EN 15376:2011 (E) 4 1 Scope This European Standard specifies requirements and test methods for marketed and delivered ethanol to be used as an extender for automotive fuel for petrol engine vehicles in accordance with the requirements of EN 228. NOTE 1 This document gives all relevant characteristics, requirements and test methods for (bio)ethanol, which are known at this time to be necessary to define the product to be used up to a maximum 10 % (V/V) blending component for automotive petrol fuel. The requirements need to be restudied if the percentage or use is expanded beyond 10 % volume. NOTE 2 For the purposes of this document, the term “% (m/m)” and “% (V/V)” are used to represent the mass fraction, µ, and the volume fraction, 3, respectively. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 228, Automotive fuels — Unleaded petrol — Requirements and test methods EN 15484:2007, Ethanol as a blending component for petrol — Determination of inorganic chloride — Potentiometric method EN 15485:2007, Ethanol as a blending component for petrol — Determination of sulfur content — Wavelength dispersive X-ray fluorescence spectrometric method EN 15486:2007, Ethanol as a blending component for petrol — Determination of sulfur content — Ultraviolet fluorescence method EN 15487:2007, Ethanol as a blending component for petrol — Determination of phosphorus content — Ammonium molybdate spectrometric method EN 15488:2007, Ethanol as a blending component fo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.