kSIST-TS FprCEN/TS 12201-7:2024

Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 7: Assessment of conformity

This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   A test matrix provides an overview of the testing scheme in Annex C, Table C.1.
NOTE 2   If certification is involved, the certification body operating in accordance with EN ISO/IEC 17065 [6] and EN ISO/IEC 17020 [4] is considered to be competent.
In conjunction with EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-4 and EN 12201-5, this document is applicable to polyethylene (PE) pressure piping systems (mains and service pipes) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application. The intended use includes sea outfalls, laid in water and pipes suspended below bridges. It is applicable to PE pipes, fittings, and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar );
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 3   Industrial application is covered by EN ISO 15494 [3].
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to and including 50 °C, see EN 12201-1:2024, Annex A.
NOTE 53   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This document gives recommendations that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [2].

Kunststoff-Rohrleitungssysteme für die Wasserversorgung und für Entwässerungs- und Abwasserdruckleitungen - Polyethylen (PE) - Teil 7: Beurteilung der Konformität

Systèmes de canalisations en plastique pour l'alimentation en eau et pour les branchements et les collecteurs d'assainissement avec pression - Polyéthylène (PE) - Partie 7 : Évaluation de la conformité

Cevni sistemi iz polimernih materialov za oskrbo z vodo in za odvodnjavanje in kanalizacijo pod tlakom - Polietilen (PE) - 7. del: Ugotavljanje skladnosti

General Information

• Status: Not Published
• Public Enquiry End Date: 30-Jul-2024
• ICS: 23.040.03 - Pipeline and its parts for external water conveyance systems
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 91.140.60 - Water supply systems
• ICS: 93.030 - External sewage systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 5520 - Unique Acceptance Procedure (UAP) (Adopted Project)
• Start Date: 06-Jun-2024
• Due Date: 24-Oct-2024
• Ref Project: FprCEN/TS 12201-7 - Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 7: Assessment of conformity

Relations

• Revises: SIST-TS CEN/TS 12201-7:2014 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
• Effective Date: 22-Nov-2023

Standards Content (Sample)

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 12201-7:2024
01-julij-2024
Cevni sistemi iz polimernih materialov za oskrbo z vodo in za odvodnjavanje in
kanalizacijo pod tlakom - Polietilen (PE) - 7. del: Ugotavljanje skladnosti
Plastics piping systems for water supply, and for drains and sewers under pressure -
Polyethylene (PE) - Part 7: Assessment of conformity
Kunststoff-Rohrleitungssysteme für die Wasserversorgung und für Entwässerungs- und
Abwasserdruckleitungen - Polyethylen (PE) - Teil 7: Beurteilung der Konformität
Systèmes de canalisations en plastique pour l'alimentation en eau et pour les
branchements et les collecteurs d'assainissement avec pression - Polyéthylène (PE) -
Partie 7 : Évaluation de la conformité
Ta slovenski standard je istoveten z: FprCEN/TS 12201-7
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.60 Sistemi za oskrbo z vodo Water supply systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
kSIST-TS FprCEN/TS 12201-7:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 12201-7:2024

---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 12201-7:2024


FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 12201-7
SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION

May 2024
ICS 23.040.05; 91.140.60 Will supersede CEN/TS 12201-7:2014
English Version

Plastics piping systems for water supply, and for drains
and sewers under pressure - Polyethylene (PE) - Part 7:
Assessment of conformity
Systèmes de canalisations en plastique pour Kunststoff-Rohrleitungssysteme für die
l'alimentation en eau et pour les branchements et les Wasserversorgung und für Entwässerungs- und
collecteurs d'assainissement avec pression - Abwasserdruckleitungen - Polyethylen (PE) - Teil 7:
Polyéthylène (PE) - Partie 7 : Évaluation de la Beurteilung der Konformität
conformité


This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 155.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 12201-7:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 12201-7:2024
FprCEN/TS 12201-7:2024 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Abbreviated terms .11
5 General .11
6 Testing and inspection .12
6.1 Grouping .12
6.1.1 General .
...