Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics fittings - Test method for impact strength (ISO 13263:2010)

ISO 13263:2010 specifies a method for testing the impact resistance of fittings by dropping them on to a rigid surface. For a fitting with seal-retaining components, such as seal-retaining caps or rings, the method includes assessment of the watertightness of the fittings when the fixing elements show disturbance as a result of the test.
It is applicable to fittings made from thermoplastics materials intended to be used for buried and above-ground applications.

Erdverlegte Rohrleitungssysteme aus Thermoplasten für drucklose erdverlegte Entwässerungs- und Abwasserleitungen - Formstücke aus Thermoplasten - Prüfverfahren der Schlagzähigkeit (ISO 13263:2010)

Diese Internationale Norm legt ein Prüfverfahren für die Schlagzähigkeit von Formstücken fest, bei dem die Formstücke auf eine harte Oberfläche fallen gelassen werden. Für ein Formstück mit Komponenten zur Dichtungsaufnahme, wie Dichtungsaufnahmekappen oder -ringen schließt das Verfahren die Feststellung der Wasserdichtheit der Formstücke ein, wenn die Fixierungselemente eine Beschädigung als Folge der Prüfung zeigen.
Diese Internationale Norm gilt für Formstücke aus Thermoplasten für den Einsatz bei erdverlegten und oberirdischen Anwendungen.

Systèmes de canalisations thermoplastiques pour branchements et collecteurs d'assainissement enterrés sans pression - Raccords thermoplastiques - Méthode d'essai de résistance au choc (ISO 13263:2010)

L'ISO 13263:2010 spécifie une méthode d'essai de résistance au choc des raccords qui consiste à les laisser tomber sur une surface rigide. Si le raccord possède des moyens de retenue des joints, par exemple des bagues de retenue, la méthode comprend l'évaluation de l'étanchéité des raccords lorsque les éléments de fixation présentent des désordres à la suite de l'essai.
L'ISO 13263:2010 s'applique aux raccords en matières thermoplastiques destinés à être utilisés pour des applications enterrées et en surface.

Plastomerni cevni sistemi za odpadno vodo in kanalizacijo, položeni v zemljo, ki delujejo po težnostnem principu - Plastomerni fitingi - Preskusna metoda za udarno trdnost (ISO 13263:2010)

Standard ISO 13263:2010 določa metodo za preskušanje odpornosti na udarce fitingov, tako da se jih spušča na trdno površino. Za fitinge s tesnilnimi komponentami, kot so tesnilni pokrovi ali obroči, metoda vključuje ocenjevanje vodotesnosti fitingov, ko so zaznane motnje pri učinkovitosti pritrdilnih elementov, ki so posledica preskusa.
Uporablja se za fitinge iz plastomernih materialov za podzemno in nadzemno uporabo.

General Information

Status
Published
Public Enquiry End Date
19-May-2017
Publication Date
12-Dec-2017
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Nov-2017
Due Date
12-Jan-2018
Completion Date
13-Dec-2017

RELATIONS

Buy Standard

Standard
SIST EN ISO 13263:2018
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 13263:2018
01-januar-2018
1DGRPHãþD
SIST EN 12061:2000
Plastomerni cevni sistemi za odpadno vodo in kanalizacijo, položeni v zemljo, ki
delujejo po težnostnem principu - Plastomerni fitingi - Preskusna metoda za
udarno trdnost (ISO 13263:2010)

Thermoplastics piping systems for non-pressure underground drainage and sewerage -

Thermoplastics fittings - Test method for impact strength (ISO 13263:2010)
Erdverlegte Rohrleitungssysteme aus Thermoplasten für drucklose erdverlegte
Entwässerungs- und Abwasserleitungen - Formstücke aus Thermoplasten -
Prüfverfahren der Schlagzähigkeit (ISO 13263:2010)
Systèmes de canalisations thermoplastiques pour branchements et collecteurs

d'assainissement enterrés sans pression - Raccords thermoplastiques - Méthode d'essai

de résistance au choc (ISO 13263:2010)
Ta slovenski standard je istoveten z: EN ISO 13263:2017
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 13263:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 13263:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 13263:2018
EN ISO 13263
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Supersedes EN 12061:1999
English Version
Thermoplastics piping systems for non-pressure
underground drainage and sewerage - Thermoplastics
fittings - Test method for impact strength (ISO
13263:2010)

Systèmes de canalisations thermoplastiques pour Erdverlegte Rohrleitungssysteme aus Thermoplasten

branchements et collecteurs d'assainissement enterrés für drucklose erdverlegte Entwässerungs- und

sans pression - Raccords thermoplastiques - Méthode Abwasserleitungen - Formstücke aus Thermoplasten -

d'essai de résistance au choc (ISO 13263:2010) Prüfverfahren der Schlagzähigkeit (ISO 13263:2010)

This European Standard was approved by CEN on 19 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13263:2017 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13263:2018
EN ISO 13263:2017 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 13263:2018
EN ISO 13263:2017 (E)
European foreword

The text of ISO 13263:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,

fittings and valves for the transport of fluids” of the International Organization for Standardization

(ISO) and has been taken over as EN ISO 13263:2017 by Technical Committee CEN/TC 155 “Plastics

piping systems and ducting systems” the secretariat of which is held by NEN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be

withdrawn at the latest by April 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 12061:1999.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 13263:2010 has been approved by CEN as EN ISO 13263:2017 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 13263:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 13263:2018
INTERNATIONAL ISO
STANDARD 13263
First edition
2010-05-01
Thermoplastics piping systems for non-
pressure underground drainage and
sewerage — Thermoplastics fittings —
Test method for impact strength
Systèmes de canalisations thermoplastiques pour branchements et
collecteurs d'assainissement enterrés sans pression — Raccords
thermoplastiques — Méthode d'essai de résistance au choc
Reference number
ISO 13263:2010(E)
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 13263:2018
ISO 13263:2010(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2010

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All right
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.