SIST EN 61000-6-3:2007/A1:2011
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or productfamily EMC emission standard exists. This standard applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, lowvoltage power distribution system if this apparatus is intended to be used in the locations described below. The environments encompassed by this standard are residential, commercial and lightindustrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included: - residential properties, for example houses, apartments; - retail outlets, for example shops, supermarkets; - business premises, for example offices, banks; - areas of public entertainment, for example cinemas, public bars, dance halls; - outdoor locations, for example petrol stations, car parks, amusement and sports centres; - light-industrial locations, for example workshops, laboratories, service centres. Locations that are characterised by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
Elektromagnetische Verträglichkeit (EMV) - Teil 6-3: Fachgrundnormen - Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie Kleinbetriebe
Compatibilité électromagnétique (CEM) - Partie 6-3: Normes génériques - Norme sur l'émission pour les environnements résidentiels, commerciaux et de l'industrie légère
Elektromagnetna združljivost (EMC) - 6-3. del: Osnovni standardi - Standard oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih okoljih - Dodatek A1 (IEC 61000-6-3:2006/A1:2010)
Ta del IEC 61000 velja za zahteve glede elektromagnetne združljivosti pri oddajanju motenj za električne in elektronske aparate, ki se uporabljajo v stanovanjskih, poslovnih in manj zahtevnih industrijskih okoljih. Zajete so zahteve za oddajanje motenj v frekvenčnem razponu od 0 Hz do 400 GHz. Kjer zahteve niso določene, ni potrebno nobeno merjenje. Ta generični standard za elektromagnetno združljivost pri oddajanju motenj velja, če ne obstaja noben ustrezen namenski standard za elektromagnetno združljivost pri oddajanju motenj za posamezen proizvod ali družino proizvodov. Ta standard velja za aparate, ki se neposredno povežejo z nizkonapetostnim javnim električnim omrežjem ali se priklopijo v namenski vir enosmernega toka, ki je vmesnik med aparatom in nizkonapetostnim javnim električnim omrežjem. Ta standard velja tudi za aparate, ki delujejo na baterije ali se napajajo prek nejavnega, a neindustrijskega nizkonapetostnega sistema za distribucijo elektrike, če se tak aparat uporablja na spodaj opisanih lokacijah. Okolja, ki jih zajema ta standard, so stanovanjske, poslovne in manj zahtevne industrijske lokacije, v zaprtih prostorih in na prostem. Spodnji seznam sicer ne zajema vsega, vendar nakazuje vključene lokacije: - stanovanjske nepremičnine, na primer hiše, stanovanja; - maloprodajna mesta, na primer trgovine, supermarketi; - poslovni prostori, na primer pisarne, banke; - površine za javne prireditve, na primer kinodvorane, javni bari, plesne dvorane; - lokacije na prostem, na primer bencinske črpalke, parkirišča, zabavišča in športni centri; - manj zahtevne industrijske lokacije, na primer delavnice, laboratoriji, storitveni centri. Lokacije, za katere je značilno neposredno nizkonapetostno napajanje iz javnega električnega omrežja, so stanovanjske, poslovne ali manj težke industrijske. Cilj tega standarda je opredeliti zahteve za preskušanje oddajanja motenj za aparate, opredeljene v tem okviru, v zvezi z neprekinjenimi in prehodnimi, vodenimi in sevanimi motnjami. Zahteve za oddajanje motenj so bile izbrane tako, da zagotovijo, da motnje, ki jih proizvaja aparat, ki deluje normalno v stanovanjski, poslovni in lažji industrijski lokaciji, ne presežejo stopnje, nad katero drugi aparati ne morejo delovati, kot je predvideno. Okoliščine okvare aparata niso upoštevane. Vsi pojavi motenj za preskušanja niso bili vključeni v ta standard; vključeni so le tisti, ki štejejo za ustrezne za opremo, ki jo zajema ta standard. Te zahteve so bistvene za elektromagnetno združljivost pri oddajanju motenj.
General Information
- Status
- Withdrawn
- Publication Date
- 10-Apr-2011
- Withdrawal Date
- 10-Apr-2024
- Technical Committee
- EMC - Electromagnetic compatibility
- Current Stage
- 9900 - Withdrawal (Adopted Project)
- Start Date
- 02-Apr-2024
- Due Date
- 25-Apr-2024
- Completion Date
- 11-Apr-2024
Relations
- Effective Date
- 01-May-2021
- Effective Date
- 01-May-2011
- Effective Date
- 01-Sep-2012
Frequently Asked Questions
SIST EN 61000-6-3:2007/A1:2011 is a standard – translation published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments". This standard covers: This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or productfamily EMC emission standard exists. This standard applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, lowvoltage power distribution system if this apparatus is intended to be used in the locations described below. The environments encompassed by this standard are residential, commercial and lightindustrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included: - residential properties, for example houses, apartments; - retail outlets, for example shops, supermarkets; - business premises, for example offices, banks; - areas of public entertainment, for example cinemas, public bars, dance halls; - outdoor locations, for example petrol stations, car parks, amusement and sports centres; - light-industrial locations, for example workshops, laboratories, service centres. Locations that are characterised by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or productfamily EMC emission standard exists. This standard applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, lowvoltage power distribution system if this apparatus is intended to be used in the locations described below. The environments encompassed by this standard are residential, commercial and lightindustrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included: - residential properties, for example houses, apartments; - retail outlets, for example shops, supermarkets; - business premises, for example offices, banks; - areas of public entertainment, for example cinemas, public bars, dance halls; - outdoor locations, for example petrol stations, car parks, amusement and sports centres; - light-industrial locations, for example workshops, laboratories, service centres. Locations that are characterised by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
SIST EN 61000-6-3:2007/A1:2011 is classified under the following ICS (International Classification for Standards) categories: 33.100.10 - Emission. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 61000-6-3:2007/A1:2011 has the following relationships with other standards: It is inter standard links to SIST EN IEC 61000-6-3:2021, SIST EN 61000-6-3:2007, SIST EN 61000-6-3:2007/A1:2011/AC:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 61000-6-3:2007/A1:2011 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, 2004/108/EC, 2004/108/EU, 2010-01-3290, 2014/30/EU, 2014/53/EU; Standardization Mandates: M/404, M/490, M/536, M/552. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 61000-6-3:2007/A1:2011 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI SIST EN 61000-6-3:2007/A1
STANDARD
maj 2011
Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni standardi –
Standard oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih
industrijskih okoljih – Dopolnilo A1 (IEC 61000-6-3:2006/A1:2010)
Electromagnetic compatibility (EMC) – Part 6-3: Generic standards –
Emission standard for residential, commercial and light-industrial environments
(IEC 61000-6-3:2006/A1:2010)
Compatibilité électromagnétique (CEM) – Partie 6-3: Normes génériques –
Norme sur l'émission pour les environnements résidentiels, commerciaux et de
l'industrie légère (CEI 61000-6-3:2006/A1:2010)
Elektromagnetische Verträglichkeit (EMV) – Teil 6-3: Fachgrundnormen –
Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie
Kleinbetriebe (IEC 61000-6-3:2006/A1:2010)
Referenčna oznaka
ICS 33.100.10 SIST EN 61000-6-3:2007/A1:2011 (sl)
Nadaljevanje na straneh II in III ter od 1 do 16
© 2016-05. Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 61000-6-3:2007/A1 : 2011
NACIONALNI UVOD
Dopolnilo SIST EN 61000-6-3:2007/A1 (sl), Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni
standardi – Standard oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih
okoljih – Dopolnilo A1 (IEC 61000-6-3:2006/A1:2010), 2011, ima status slovenskega dopolnila in je
istoveten evropskemu dopolnilu EN 61000-6-3:2007/A1 (en), Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards – Emission standard for residential, commercial and light-industrial
environments (IEC 61000-6-3:2006/A1:2010), 2011.
NACIONALNI PREDGOVOR
Evropsko dopolnilo EN 61000-6-3:2007/A1:2011 je pripravil tehnični odbor CLC/TC 210
Elektromagnetna združljivost (EMC). Slovensko dopolnilo SIST EN 61000-6-3:2007/A1:2011 je prevod
evropskega dopolnila EN 61000-6-3:2007/A1:2011. V primeru spora glede besedila slovenskega
prevoda v tem dopolnilu je odločilno izvirno evropsko dopolnilo v angleškem jeziku. Slovensko izdajo
dopolnila je potrdil tehnični odbor SIST/TC EMC Elektromagnetna združljivost.
Odločitev za privzem tega dopolnila je v maju 2011 sprejel tehnični odbor SIST/TC EMC
Elektromagnetna združljivost.
ZVEZA Z NACIONALNIMI STANDARDI
S privzemom tega evropskega dopolnila veljajo za omejeni namen referenčnih standardov vsi
standardi, navedeni v izvirniku, razen tistih, ki so že sprejeti v nacionalno standardizacijo:
SIST EN 61000-4-20:2011 Elektromagnetna združljivost (EMC) – 4-20. del: Preskusne in
merilne tehnike – Preskušanje oddajanja in odpornosti v
prečnih elektromagnetnih (TEM) valovodih (IEC 61000-4-
20:2010)
SIST EN 55016-1-1:2010 Specifikacija merilnih naprav in metod za merjenje radijskih
motenj in odpornosti – 1-1. del: Merilne naprave za merjenje
radijskih motenj in odpornosti – Merilne naprave
SIST EN 55016-1-4:2007 Specifikacija merilnih naprav in metod za merjenje
SIST EN 55016-1-4:2007/A1:2008 radiofrekvenčnih motenj in odpornosti – 1-4. del: Merilne
naprave za merjenje radiofrekvenčnih motenj in odpornosti –
Antene in preskuševališča za meritve sevanih motenj (CISPR
16-1-4:2007)
SIST EN 61000-3-2:2006 Elektromagnetna združljivost (EMC) – 3-2. del: Mejne
SIST EN 61000-3-2:2006/A1:2009 vrednosti – Mejne vrednosti za oddajanje harmonskih tokov
SIST EN 61000-3-2:2006/A2:2009 (vhodni tok opreme do vključno 16 A na fazo) (IEC 61000-3-
2:2005)
SIST EN 61000-3-3:2009 Elektromagnetna združljivost (EMC) – 3-3. del: Mejne
vrednosti – Omejitev vrednosti kolebanja napetosti in flikerja v
nizkonapetostnih napajalnih sistemih za opremo z
naznačenim tokom do 16 A in ni priključena pod posebnimi
pogoji (IEC 61000-3-3:2008)
SIST EN 61000-3-11:2001 Elektromagnetna združljivost (EMC) – 3-11. del: Mejne
vrednosti – Mejne vrednosti napetostnih sprememb,
kolebanja napetosti in flikerja v javnih nizkonapetostnih
napajalnih sistemih – Oprema z naznačenim tokom do
vključno 75 A, ki je predmet pogojnega priklopa
II
SIST EN 61000-6-3:2007/A1 : 2011
SIST EN 61000-3-12:2005 Elektromagnetna združljivost (EMC) – 3-12. del: Mejne
vrednosti – Mejne vrednosti za harmonske tokove, ki jih
povzroča oprema, priključena na nizkonapetostne napajalne
sisteme z naznačenim tokom, večjim od 16 A in ≤ 75 A po
liniji (IEC 61000-3-12:2004)
SIST EN 55014-1:2007 Elektromagnetna združljivost – Zahteve za (električne)
SIST EN 55014-1:2007/A1:2009 gospodinjske aparate, električna ročna orodja in podobne
aparate – 1. del: Oddajanje (CISPR 14-1:2005)
SIST EN 55016-1-2:2005 Specifikacija za merilne naprave in metode za merjenje
SIST EN 55016-1-2:2005/A1:2005 radijskih motenj in odpornosti – 1-2. del: Merilne naprave za
SIST EN 55016-1-2:2005/A2:2007 merjenje radijskih motenj in odpornosti – Pomožna oprema –
Motnje po vodnikih (CISPR 16-1-2:2003)
SIST EN 55016-2-1:2009 Specifikacija za merilne naprave in metode za merjenje
radijskih motenj in odpornosti – 2-1. del: Metode za merjenje
radijskih motenj in odpornosti – Merjenje motenj po vodnikih
SIST EN 55016-2-3:2007 Specifikacija merilnih naprav in metod za merjenje radijskih
motenj in odpornosti – 2-3. del: Metode za merjenje radijskih
motenj in odpornosti – Merjenje sevanih motenj (CISPR 16-2-
3:2006)
SIST EN 55016-4-2:2005 Specifikacija za merilne naprave in metode za merjenje
radijskih motenj in odpornosti – 4-2. del: Modeliranje
negotovosti, statistike in mejnih vrednosti – Negotovost pri
meritvah EMC (CISPR 16-4-2:2003)
SIST EN 55022:2011 Oprema za informacijsko tehnologijo – Karakteristike
občutljivosti za radijske motnje – Mejne vrednosti in merilne
metode
OSNOVA ZA IZDAJO DOPOLNILA
– privzem dopolnila EN 61000-6-3:2007/A1:2011
OPOMBE
– Povsod, kjer se v besedilu dopolnila uporablja izraz "evropsko" ali "mednarodno" dopolnilo, v
– Nacionalni uvod in nacionalni predgovor nista sestavni del dopolnila.
– Ta nacionalni dokument je istoveten EN 61000-6-3:2007/A1:2011 in je objavljen z dovoljenjem
CEN/CENELEC
Upravni center
Avenue Marnix 17
B-1000 Bruselj
This national document is identical with EN 61000-6-3:2007/A1:2011 and is published with the
permission of
CEN/CENELEC
Management Centre
Avenue Marnix 17
B -1000 Brussels
III
EVROPSKI STANDARD EN 61000-6-3/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM marec 2011
ICS: 33.100.10
Slovenska izdaja
Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni standardi – Standard
oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih
okoljih – Dopolnilo A1 (IEC 61000-6-3:2006/A1:2010)
Electromagnetic compatibility Compatibilité électromagnétique Elektromagnetische Verträglichkeit
(EMC) – Part 6-3: Generic (CEM) – Partie 6-3: Normes (EMV) – Teil 6-3: Fachgrundnormen
standards – Emission standard génériques – Norme sur l'émission – Störaussendung für Wohnbereich,
for residential, commercial and pour les environnements Geschäfts- und Gewerbebereiche
light-industrial environments résidentiels, commerciaux et de sowie Kleinbetriebe (IEC 61000-6-
(IEC 61000-6-3:2006/A1:2010) l'industrie légère (CEi 61000-6- 3:2006/A1:2010)
3:2006/A1:2010)
To dopolnilo A1 spreminja evropski standard EN 61000-6-3:2007 in ga je CENELEC sprejel
12. januarja 2011. Člani CENELEC morajo izpolnjevati notranje predpise CEN/CENELEC, s katerimi
so predpisani pogoji za privzem tega dopolnila na nacionalno raven brez kakršnihkoli sprememb.
Najnovejši seznami teh nacionalnih standardov z njihovimi bibliografskimi podatki se na zahtevo lahko
dobijo pri Centralnem sekretariatu ali kateremkoli članu CENELEC.
Ta dopolnilo obstaja v treh uradnih izdajah (angleški, francoski in nemški). Izdaje v drugih jezikih, ki jih
člani CENELEC na lastno odgovornost prevedejo in izdajo ter prijavijo pri Centralnem sekretariatu,
veljajo kot uradne izdaje.
Člani CENELEC so nacionalni elektrotehniški komiteji Avstrije, Belgije, Bolgarije, Cipra, Češke
republike, Danske, Estonije, Finske, Francije, Grčije, Hrvaške, Islandije, Irske, Italije, Latvije, Litve,
Luksemburga, Madžarske, Malte, Nemčije, Nizozemske, Norveške, Poljske, Portugalske, Romunije,
Slovaške, Slovenije, Španije, Švedske, Švice in Združenega kraljestva.
CENELEC
Evropski komite za standardizacijo v elektrotehniki
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Upravni center: Avenue Marnix 17, B-1000 Bruselj
© 2011 CENELEC Lastnice avtorskih pravic so vse države članice CENELEC. Ref. št. EN 61000-6-3:2007/A1:2011 E
SIST EN 61000-6-3:2007/A1 : 2011
Predgovor k evropskemu dopolnilu
Besedilo dokumenta CISPR/H/206/FDIS, prihodnje dopolnilo 1 k IEC 61000-6-3:2006, ki ga je pripravil
pododbor CISPR SC H Meje za zaščito radijskih storitev, je CENELEC po vzporednem glasovanju v
IEC in CENELEC 1. januarja 2011 sprejel kot dopolnilo A1 k EN 61000-6-3:2007.
Opozoriti je treba na možnost, da bi lahko bil kateri od elementov tega dokumenta predmet patentnih
pravic. CEN in CENELEC nista odgovorna za identificiranje nobene od teh patentnih pravic.
Določena sta bila naslednja datuma:
– zadnji datum, do katerega mora dopolnilo dobiti status
nacionalnega dopolnila bodisi z objavo istovetnega besedila
ali z razglasitvijo (dop) 2011-10-01
– zadnji datum, ko je treba razveljaviti nacionalne standarde,
ki so z dopolnilom v nasprotju (dow) 2009-12-01
Dodatek ZA je dodal CENELEC.
Razglasitvena objava
Besedilo dopolnila 1:2010 k mednarodnemu standardu IEC 61000-6-3:2006 je CENELEC odobril kot
dopolnilo k evropskemu standardu brez kakršnihkoli sprememb.
SIST EN 61000-6-3:2007/A1 : 2011
Dodatek ZA
(normativni)
Normativna sklicevanja na mednarodne publikacije z njihovimi ustreznimi
evropskimi publikacijami
Za uporabo tega standarda so, delno ali v celoti, nujno potrebni spodaj navedeni referenčni
dokumenti. Pri datiranih sklicevanjih se uporablja le navedena izdaja. Pri nedatiranih sklicevanjih se
uporablja zadnja izdaja publikacije (vključno z dopolnili).
OPOMBA: Kadar je bila mednarodna publikacija spremenjena s skupnimi spremembami, označenimi z (mod), se
uporablja ustrezni EN/HD.
Standard Leto Naslov EN/HD Leto
Dodati obstoječemu seznamu naslednja nova sklicevanja:
IEC 60050-161 - Mednarodni elektrotehniški slovar (IEV) – - -
Poglavje 161: Elektromagnetna združljivost
IEC 61000-4-20 2010 Elektromagnetna združljivost (EMC) – EN 61000-4-20 2010
4-20. del: Preskusne in merilne tehnike –
Preskušanje oddajanja in odpornosti v
prečnih elektromagnetnih (TEM) valovodih
CISPR 16-1-1 2010 Specifikacija za aparate in metode za EN 55016-1-1 2010
merjenje radijskega motenja in odpornosti
– 1-1. del: Aparat za merjenje radijskih
motenj in odpornosti – Merilni aparat
1)
CISPR 16-1-4 2007 Specifikacija za merilne naprave in metode EN 55016-1-4 2007
+ A1 2007 za merjenje radiofrekvenčnih motenj in +A1 2008
odpornosti – 1-4. del: Merilne naprave za
merjenje radiofrekvenčnih motenj in
odpornosti - Pomožna oprema - Sevane
motnje
Zamenjati obstoječa sklicevanja z naslednjimi novimi sklicevanji:
IEC 61000-3-2 2005 Elektromagnetna združljivost (EMC) – EN 61000-3-2 2006
+ A1 2008 3-2. del: Mejne vrednosti – Mejne vrednosti + A1 2009
+ A2 2009 za oddajanje harmonskih tokov (vhodni tok + A2 2009
opreme do vključno 16 A na fazo)
IEC 61000-3-3 2008 Elektromagnetna združljivost (EMC) – EN 61000-3-3 2008
3-3. del: Mejne vrednosti – Omejitev
vrednosti kolebanja napetosti in flikerja v
nizkonapetostnih napajalnih sistemih za
opremo z naznačenim tokom do 16 A in ni
priključena pod posebnimi pogoji
1)
EN 55016-1-4 je nadomeščen z EN 55016-1-4:2010, ki temelji na CISPR 16-1-4:2010 + popravek December 2010.
SIST EN 61000-6-3:2007/A1 : 2011
IEC 61000-3-11 2000 Elektromagnetna združljivost (EMC) – EN 61000-3-11 2000
3-11. del: Mejne vrednosti – Mejne
vrednosti napetostnih sprememb,
kolebanja napetosti in flikerja v javnih
nizkonapetostnih napajalnih sistemih –
Oprema z naznačenim tokom do vključno
...
SLOVENSKI STANDARD
01-maj-2011
Elektromagnetna združljivost (EMC) - 6-3. del: Osnovni standardi - Standard
oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih
okoljih - Dodatek A1 (IEC 61000-6-3:2006/A1:2010)
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard
for residential, commercial and light-industrial environments
Elektromagnetische Verträglichkeit (EMV) - Teil 6-3: Fachgrundnormen -
Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie Kleinbetriebe
Compatibilité électromagnétique (CEM) - Partie 6-3: Normes génériques - Norme sur
l'émission pour les environnements résidentiels, commerciaux et de l'industrie légère
Ta slovenski standard je istoveten z: EN 61000-6-3:2007/A1:2011
ICS:
33.100.10 Emisija Emission
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 61000-6-3/A1
NORME EUROPÉENNE
March 2011
EUROPÄISCHE NORM
ICS 33.100.10
English version
Electromagnetic compatibility (EMC) -
Part 6-3: Generic standards -
Emission standard for residential, commercial and light-industrial
environments
(IEC 61000-6-3:2006/A1:2010)
Compatibilité électromagnétique (CEM) - Elektromagnetische Verträglichkeit (EMV) -
Partie 6-3: Normes génériques - Teil 6-3: Fachgrundnormen -
Norme sur l'émission pour les Störaussendung für Wohnbereich,
environnements résidentiels, Geschäfts- und Gewerbebereiche sowie
commerciaux et de l'industrie légère Kleinbetriebe
(CEI 61000-6-3:2006/A1:2010) (IEC 61000-6-3:2006/A1:2010)
This amendment A1 modifies the European Standard EN 61000-6-3:2007; it was approved by CENELEC on
2011-01-12. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61000-6-3:2007/A1:2011 E
Foreword
The text of document CISPR/H/206/FDIS, future amendment 1 to IEC 61000-6-3:2007, prepared by
CISPR SC H, Limits for the protection of radio services, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as amendment A1 to EN 61000-6-3:2007 on 2011-01-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be
implemented at national level by publication of
(dop) 2011-10-01
an identical national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-01-01
with the amendment have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of amendment 1:2010 to the International Standard IEC 61000-6-3:2007 was approved by
CENELEC as an amendment to the European Standard without any modification.
__________
- 3 - EN 61000-6-3:2007/A1:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
Add the following new references to the existing list:
IEC 60050-161 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 161: Electromagnetic compatibility
IEC 61000-4-20 2010 Electromagnetic compatibility (EMC) - EN 61000-4-20 2010
Part 4-20: Testing and measurement
techniques - Emission and immunity testing in
transverse electromagnetic (TEM)
waveguides
CISPR 16-1-1 2010 Specification for radio disturbance and EN 55016-1-1 2010
immunity measuring apparatus and methods -
Part 1-1: Radio disturbance and immunity
measuring apparatus - Measuring apparatus
1)
CISPR 16-1-4 2007 Specification for radio disturbance and EN 55016-1-4 2007
+ A1 2007 immunity measuring apparatus and methods - +A1 2008
Part 1-4: Radio disturbance and immunity
measuring apparatus - Ancillary equipment -
Radiated disturbances
Replace the existing references by the following new references:
IEC 61000-3-2 2005 Electromagnetic compatibility (EMC) - EN 61000-3-2 2006
+ A1 2008 Part 3-2: Limits - Limits for harmonic current + A1 2009
+ A2 2009 emissions (equipment input current ≤ 16 A + A2 2009
per phase)
IEC 61000-3-3 2008 Electromagnetic compatibility (EMC) - EN 61000-3-3 2008
Part 3-3: Limits - Limitation of voltage
changes, voltage fluctuations and flicker in
public low-voltage supply systems, for
equipment with rated current ≤ 16 A per phase
and not subject to conditional connection
IEC 61000-3-11 2000 Electromagnetic compatibility (EMC) - EN 61000-3-11 2000
Part 3-11: Limits - Limitation of voltage
changes, voltage fluctuations and flicker in
public low-voltage supply systems -
Equipment with rated current ≤ 75 A and
1)
EN 55016-1-4 is superseded by EN 55016-1-4:2010, which is based on CISPR 16-1-4:2010 + corr. December 2010.
Publication Year Title EN/HD Year
subject to conditional connection
IEC 61000-3-12 2004 Electromagnetic compatibility (EMC) - EN 61000-3-12 2005
Part 3-12: Limits - Limits for harmonic currents
produced by equipment connected to public
low-voltage systems with input current > 16 A
and ≤ 75 A per phase
CISPR 14-1 2005 Electromagnetic compatibil ty - EN 55014-1 2006
+ A1 2008 Requirements for household appliances, + A1 2009
electric tools and similar apparatus -
Part 1: Emission
CISPR 16-1-2 2003 Specification for radio disturbance and EN 55016-1-2 2004
+ A1 2004 immunity measuring apparatus and methods - + A1 2005
+ A2 2006 Part 1-2: Radio disturbance and immunity + A2 2006
measuring apparatus - Ancillary equipment -
Conducted disturbances
CISPR 16-2-1 2008 Specification for radio disturbance and EN 55016-2-1 2009
immunity measuring apparatus and methods -
Part 2-1: Methods of measurement of
disturbances and immunity - Conducted
disturbance measurements
2)
CISPR 16-2-3 2006 Specification for radio disturbance and EN 55016-2-3 2006
immunity measuring apparatus and methods -
Part 2-3: Methods of measurement of
disturbances and immunity - Radiated
disturbance measurements
CISPR 16-4-2 2003 Specification for radio disturbance and EN 55016-4-2 2004
immunity measuring apparatus and methods -
Part 4-2: Uncertainties, statistics and limit
modelling - Uncertainty in EMC
measurements
CISPR 22 (mod) 2008 Information technology equipment - Radio EN 55022 2010
disturbance characteristics - Limits and
methods of measurement
2)
EN 55016-2-3 is superseded by EN 55016-2-3:2010, which is based on CISPR 16-2-3:2010.
IEC 61000-6-3 ®
Edition 2.0 2010-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
AMENDMENT 1
AMENDEMENT 1
Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards – Emission standard for residential, commercial
and light-industrial environments
Compatibilité électromagnétique (CEM) –
Partie 6-3: Normes génériques – Norme sur l'émission pour les environnements
résidentiels, commerciaux et de l'industrie légère
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
M
CODE PRIX
ICS 33.100.10 ISBN 978-2-88912-252-3
– 2 – 61000-6-3 Amend. 1 Ó IEC:2010
FOREWORD
This amendment has been prepared by CISPR subcommittee H: Limits for the protection of
radio services.
The text of this amendment is based on the following documents:
FDIS Report on voting
CISPR/H/206/FDIS CISPR/H/210/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication
will remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
Contents
Replace the title of Clause 3 by the following new title:
3 Terms, definitions and abbreviations
Replace the title of Clause 8 by the following new title:
8 Measurement uncertainty
Replace the title of Clause 9 by the following new title:
9 Application of limits in tests for conformity of equipment in series production
Add the following new Clauses 10 and 11:
10 Compliance with this standard
11 Emission test requirements
Replace the title of Table 1 by the following new title:
Table 1 - Emission – Enclosure port
Add the following new Tables:
Table 2 - Emission - Low voltage AC mains port
61000-6-3 Amend. 1 Ó IEC:2010 – 3 –
Table 3 – Emission – DC power port
2 Normative references
Add the following new references to the existing list:
IEC 60050-161, International Electrotechnical Vocabulary (IEV) - Chapter 161:
Electromagnetic compatibility
IEC 61000-4-20:2010, Electromagnetic compatibility (EMC) – Part 4-20: Testing and
measurement techniques – Emission and immunity testing in transverse electromagnetic
(TEM) waveguide
CISPR 16-1-1:2010, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 1-1: Radio disturbance and immunity measuring apparatus – Measuring
apparatus
CISPR 16-1-4:2007, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 1-4: Radio disturbance and immunity measuring apparatus – Ancillary
equipment – Radiated disturbances
Amendment 1:2007
Replace the existing references by the following new references:
IEC 61000-3-2:2005 Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for
harmonic current emissions (equipment input current £ 16 A per phase)
Amendment 1:2008
Amendment 2:2009
IEC 61000-3-3:2008, Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of
voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for
equipment with rated current £ 16 A per phase and not subject to conditional connection
IEC 61000-3-11:2000, Electromagnetic compatibility (EMC) – Part 3-11: Limits – Limitation
of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems –
Equipment with rated current £ 75 A and subject to conditional connection
IEC 61000-3-12:2004, Electromagnetic compatibility (EMC) – Part 3-12: Limits – Limits for
harmonic currents produced by equipment connected to public low-voltage systems with
input current > 16 A and £ 75 A per phase
CISPR 14-1:2005, Electromagnetic compatibility – Requirements for household appliances,
electric tools and similar apparatus – Part 1: Emission
Amendment 1:2008
CISPR 16-1-2:2003, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 1-2: Radio disturbance and immunity measuring apparatus – Ancillary
equipment – Conducted disturbances
Amendment 1:2004
Amendment 2:2006
CISPR 16-2-1:2008, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 2-1: Methods of measurement of disturbances and immunity –
Conducted disturbance measurements
– 4 – 61000-6-3 Amend. 1 Ó IEC:2010
CISPR 16-2-3:2006
...
The standard SIST EN 61000-6-3:2007/A1:2011 addresses the essential electromagnetic compatibility (EMC) emission requirements for electrical and electronic apparatus used in residential, commercial, and light-industrial environments. Its scope is comprehensive, covering emission requirements for a wide frequency range from 0 Hz to 400 GHz, ensuring that a variety of devices can meet necessary EMC standards without requiring measurement at frequencies lacking specified requirements. One of the strengths of this standard is its applicability to a broad array of environments, including homes, retail outlets, business premises, public entertainment areas, and various outdoor and light-industrial locations. This inclusiveness ensures that manufacturers and users of electronic and electrical apparatus comprehend the required emission limits that will aid in maintaining the operational integrity of surrounding devices. The standard stipulates clear emission test requirements related to both continuous and transient disturbances, including conducted and radiated disturbances. By focusing on essential electromagnetic compatibility emission requirements, it safeguards the functionality of other equipment by ensuring that the emissions from normal apparatus operations do not exceed acceptable levels. Another notable aspect is that this standard serves as a generic EMC emission standard, particularly useful when no dedicated product or product-family EMC emission standard exists. This provides flexibility and a framework for compliance in the absence of more specific guidelines, thus promoting a wider adoption of EMC practices. Furthermore, the standard's relevance is underscored by its aim to tackle only those disturbance phenomena that are pertinent to equipment found in the specified environments. This targeted approach guarantees that resources are expended efficiently in testing while ensuring that the most significant emissions are controlled. In summary, SIST EN 61000-6-3:2007/A1:2011 presents a robust and relevant framework for managing electromagnetic emissions from electrical and electronic devices in various environments, contributing to the overall electromagnetic compatibility and operational reliability of connected apparatus.
SIST EN 61000-6-3:2007/A1:2011 표준은 전자파 적합성(EMC)과 관련하여 주거, 상업 및 경량 산업 환경에서 사용될 전기 및 전자 장비에 대한 방출 요구사항을 정의합니다. 이 표준의 적용 범위는 0Hz에서 400GHz까지의 주파수 범위에서 장비가 발생할 수 있는 전자기 방출을 포함하며, 관련된 전용 제품 또는 제품 군 EMC 방출 표준이 없을 경우에도 적용될 수 있습니다. 이 표준의 주요 강점 중 하나는 다양한 환경에서 전자기 방출을 평가하는 데 필요한 테스트 요구사항을 명확하게 정립하고 있다는 점입니다. 주거지, 소매업체, 사무실, 공공 오락 시설 및 경량 산업 위치 등 다양한 장소에서의 적용 가능성을 강조하여, 실제 사용 환경을 충분히 고려하고 있습니다. 이에 따라, 이 표준은 실제로 사용되는 전기 및 전자 장비의 기능이나 성능을 저해하지 않도록 하는 데 중점을 두고 있습니다. 또한, 이 표준은 고압 전력망에 직접 연결되거나 저전압 전기망과 인터페이스되는 장비, 배터리로 작동되는 장비 등 다양한 전원 공급 방식에 적용됩니다. 이는 전자기 간섭을 최소화하여 다른 장비들과의 호환성을 보장하는 데 기여하며, 따라서 상업적 및 주거적 환경에서 전자기 적합성을 유지하게 됩니다. 포괄적으로, SIST EN 61000-6-3:2007/A1:2011 표준은 전자기 방출에 대한 필수 규정을 제시하며, 정상 작동 시 발생할 수 있는 방해 요소가 다른 장비의 기능을 저해하지 않도록 설계되었습니다. 이러한 방출 요구 사항은 전자기 적합성을 유지하고, 다양한 환경에서 시장의 요구를 충족하는 역할을 하는 중요한 기준으로 자리잡고 있습니다.
SIST EN 61000-6-3:2007/A1:2011は、住宅、商業、軽工業環境における電磁両立性（EMC）の発 EM 標準に関する重要な文書です。この標準の範囲は、低電圧の公共電源ネットワークに直接接続されるために設計された電気および電子機器に対する発 EM 要件を明確に定義しています。0 Hzから400 GHzまでの周波数範囲における発 EM 要件が含まれるため、幅広い用途に適用可能です。 この標準の強みは、特定の製品や製品ファミリーに関連するEMC発 EM 標準が存在しない場合にも適用されるという点です。これにより、関連する発 EM 規制が不足している市場ニーズに応じて、標準が提供する一貫性が確保されます。規定された発 EM 試験要件は、一般的な住宅や商業の環境において、装置が通常の運用中に発生する干渉が他の機器の正常な動作を妨げないレベルに制約されることを保証します。 さらに、この文書は、連続的および過渡的な伝導および放射障害に関連する発 EM のテスト要件を定義し、特に対象とする場所（住宅、商業、軽工業の屋内および屋外）の多様性を考慮しています。住宅、ショップ、オフィス、公共の娯楽施設など、具体的に挙げられた場所において、標準の適用範囲が明確に示されているため、関係者が現場の特性に応じた対策を講じやすくなっています。 最後に、故障時の状態は考慮されておらず、試験目的に含まれているのは、対象機器に関連性があると見なされた干渉現象のみです。この点において、SIST EN 61000-6-3:2007/A1:2011が提供する発 EM 要件は、重要な電磁両立性の枠組みを構築し、ユーザーや製造者に貴重な指針を与えていることが強調されます。このように、標準の適用性と関連性は、電磁干渉の管理において重要な役割を果たします。
Das Dokument SIST EN 61000-6-3:2007/A1:2011 befasst sich mit der elektromagnetischen Verträglichkeit (EMV) und bietet einen umfassenden Rahmen für die Emissionsstandards im Bereich der Wohn-, Geschäfts- und Leichtindustrieumgebungen. Es stellt sicher, dass elektrische und elektronische Geräte, die in diesen Umgebungen eingesetzt werden, die festgelegten Emissionsanforderungen einhalten, um Störungen zu minimieren, die die Funktion anderer Geräte beeinträchtigen könnten. Die Reichweite dieser Norm ist sehr bedeutend, da sie ein breites Spektrum an Frequenzen von 0 Hz bis 400 GHz abdeckt. Dies ermöglicht es, eine Vielzahl von Geräten zu berücksichtigen, die mit dem öffentlichen Stromnetz oder mit spezifischen Niederspannungsquellen verbunden sind. Die Tatsache, dass keine Messungen bei Frequenzen erforderlich sind, für die keine Anforderungen angegeben sind, vereinfacht die Einhaltung für Hersteller und Benutzer von Geräten und fördert eine praktische Anwendung. Ein wesentlicher Stärke der Norm ist ihre Flexibilität. Da sie als allgemeine EMV-Emissionsnorm fungiert, kommt sie zur Anwendung, wenn keine spezifischeNorm für ein bestimmtes Produkt oder Produktgruppe existiert. Dies erleichtert die Markteinführung und die Einhaltung von Vorschriften, insbesondere für neue oder innovative Produkte, die möglicherweise keinen spezifischen Standards unterliegen. Die Norm ist besonders relevant für zahlreiche Anwendungen in Wohn-, Gewerbe- und Leichtindustriebereichen, die in der Norm explizit aufgeführt sind, darunter Wohnanlagen, Einzelhandelsgeschäfte, Büros sowie öffentliche Unterhaltungsstätten. Dadurch wird gewährleistet, dass ein breiter Nutzen für verschiedene Nutzergruppen erzielt wird. Zusätzlich behandelt die Norm kontinuierliche und transiente Störungen sowie leitungsgebundene und abgestrahlte Störungen, was eine umfassende Betrachtung der unterschiedlichen Arten von EMV-Emissionen gewährleistet. Es ist wichtig zu beachten, dass diese Anforderungen gezielt ausgewählt wurden, um die gesamte elektromagnetische Verträglichkeit der betroffenen Geräte zu optimieren, und nicht alle möglichen Störungsphänomene abdeckt, was den Fokus auf relevante Testverfahren lenkt. Insgesamt stellt die SIST EN 61000-6-3:2007/A1:2011 eine fundamentale Ressource dar, um die elektromagnetische Verträglichkeit von Geräten in Wohn-, Geschäfts- und Leichtindustrieumgebungen zu gewährleisten und trägt so zur Funktionsfähigkeit des gesamten Elektrosystems bei.
Le document SIST EN 61000-6-3:2007/A1:2011 constitue une référence essentielle dans le domaine de la compatibilité électromagnétique (CEM), en particulier pour les environnements résidentiels, commerciaux et légers industriels. Cette norme s'applique aux appareils électriques et électroniques destinés à une utilisation dans ces contextes variés, allant de maisons et appartements à des bureaux et des centres commerciaux, en passant par des ateliers et des lieux de divertissement publics. L'un des points forts de cette norme est son champ d'application étendu, couvrant une large gamme de fréquences, de 0 Hz à 400 GHz. Ceci permet d'adapter les exigences de CEM aux différentes applications et configurations des appareils, tout en garantissant que les perturbations générées par ces derniers ne nuisent pas au fonctionnement d'autres équipements. En spécifiant que les mesures ne doivent pas être effectuées à des fréquences où aucune exigence n'est établie, la norme simplifie également le processus de conformité pour les fabricants et les utilisateurs. Le document met en avant des exigences d'émission qui ont été soigneusement sélectionnées pour prévenir les perturbations, qu'elles soient continues ou transitoires, conduites ou rayonnées. Cela souligne l'importance de la protection des autres équipements et systèmes électroniques dans les environnements couverts par cette norme. En établissant une base pour les tests d'émission, cette norme permet d'assurer que les appareils fonctionnent dans des conditions sans interférences indésirables, renforçant ainsi l'intégrité opérationnelle à travers divers secteurs. Il est à noter que bien que toutes les phénomènes de perturbation ne soient pas inclus pour les tests, ceux considérés comme pertinents ont été judicieusement sélectionnés, reflétant une compréhension approfondie des défis de la compatibilité électromagnétique. Cela rend la norme non seulement pertinente mais essentielle pour les fabricants et les utilisateurs d'appareils électriques au sein des sphères résidentielle, commerciale et légère industrielle. En résumé, la norme SIST EN 61000-6-3:2007/A1:2011 représente un cadre incontournable pour garantir que les exigences d'émission en matière de compatibilité électromagnétique soient respectées dans des environnements variés, promouvant ainsi une coexistence harmonieuse des technologies électroniques au quotidien.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...