This document specifies the requirements for tempered soda-lime float glass plies which are made from annealed glass either of the universally available type or of high light transmission type. The annealed glass is manufactured by a continuous process for general use.
The plies are tempered by either a thermal or chemical process.
The tempered glass is used mainly for cockpit glazing.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for tempered soda-lime float glass plies which are made from
annealed glass either of the universally available type or of high light transmission type. The annealed
glass is manufactured by a continuous process for general use.
The plies are tempered by either a thermal or chemical process.
The tempered glass is used mainly for cockpit glazing.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements relating to:
Aluminium alloy 2014A-
T6
Tubes for structures
0,6 mm ≤ a ≤12,5 mm

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the determination of visible light transmission for transparent materials by using a photometer employing a defined light source and a photocell matched to the response of the human eye.
Because the materials under test are basically colourless, certain deviations from ideal conditions, indicated in the test, are allowable.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method of measurement of optical distortion of sheets in transparent materials, which consists of determining the change of deviation over the entire area of the sheet.
The method allows sheets to be viewed at differing angles which are specified according to the quality of the sheet under test.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the determination of the haze of planar sections of transparent plastics, using a hazemeter based on an integrating sphere. This method is not recommended for the measurement of haze values greater than 30 % as determined by this method.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the resistance of transparent sheet to the effect of a solvent environment while set up as a cantilever beam with a load applied at the free end. No method has been developed yet for specimens with a thickness < 6 mm; for such material, a test method shall be agreed between the supplier and the customer.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies how the resistance to crack propagation of rigid transparent sheet is to be determined.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of the refractive index applicable for transparent materials used in aircraft glazing.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method to determine the reversible linear thermal expansion of plastics with exclusion of changes in length due to accidental factors such as changes in moisture content, degree of polymerization and stressrelease. Since it will not be possible to exclude all these accidental factors, the method can be expected to give only approximate values.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of the water absorption by means of immersion in conformance with ISO 62, method 1, applicable for transparent materials. In addition, it specifies the particular conditions for aircraft glazing.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of the 1/10 Vicat softening temperature of transparent thermoplastic materials used for aircraft glazing.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies a procedure for determining the temperature at which an arbitrary deformation occurs when the specimens are subjected to arbitrary bending loads, under conditions of continually rising temperatures.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of optical deviation caused to beam of light passing through a transparent element materialperpendicular to the optical axis of the system.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard defines the method of indicating on drawings, with the exception of engine drawings, the instructions for the marking of parts and assemblies for aerospace applications

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method to determine the reversible linear thermal expansion of plastics with exclusion of changes in length due to accidental factors such as changes in moisture content, degree of polymerization and stressrelease. Since it will not be possible to exclude all these accidental factors, the method can be expected to give only approximate values.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of optical deviation caused to beam of light passing through a transparent element materialperpendicular to the optical axis of the system.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the resistance of transparent sheet to the effect of a solvent environment while set up as a cantilever beam with a load applied at the free end. No method has been developed yet for specimens with a thickness < 6 mm; for such material, a test method shall be agreed between the supplier and the customer.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Covers the methodology of calculating for the determination of the internal volumes of both the main deck and the lower deck aircraft cargo compartments. The minimum required clearance between the compartment envelope and the unit load devices (ULDs) is also stated in order to provide the maximum ULD external contour and the methodology to define the ULD internal volumes.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off

This standard specifies the method used for the determination of the 1/10 Vicat softening temperature of transparent thermoplastic materials used for aircraft glazing.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies a procedure for determining the temperature at which an arbitrary deformation occurs when the specimens are subjected to arbitrary bending loads, under conditions of continually rising temperatures.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of the refractive index applicable for transparent materials used in aircraft glazing.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method used for the determination of the water absorption by means of immersion in conformance with ISO 62, method 1, applicable for transparent materials. In addition, it specifies the particular conditions for aircraft glazing.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard defines the method of indicating on drawings, with the exception of engine drawings, the instructions for the marking of parts and assemblies for aerospace applications

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the method of measurement of optical distortion of sheets in transparent materials, which consists of determining the change of deviation over the entire area of the sheet.
The method allows sheets to be viewed at differing angles which are specified according to the quality of the sheet under test.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the determination of visible light transmission for transparent materials by using a photometer employing a defined light source and a photocell matched to the response of the human eye.
Because the materials under test are basically colourless, certain deviations from ideal conditions, indicated in the test, are allowable.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies how the resistance to crack propagation of rigid transparent sheet is to be determined.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the determination of the haze of planar sections of transparent plastics, using a hazemeter based on an integrating sphere. This method is not recommended for the measurement of haze values greater than 30 % as determined by this method.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Includes a list of terms in English, French, Russian and German. The list is given in English in alphabetical order. This list is the tenth part of equivalent terms used in the field of aerospace construction.

  • Standard
    26 pages
    English language
    sale 15% off
  • Standard
    26 pages
    English, French and Russian language
    sale 15% off