ASTM E2518-11
(Specification)Standard Specification for Cargo Bed Cover, Type IV (M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/ M1082, 5 Ton MTV Trailer)
Standard Specification for Cargo Bed Cover, Type IV (M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/ M1082, 5 Ton MTV Trailer)
ABSTRACT
This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/M1095, 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport. Materials shall be tested and shall conform to the general requirements such as first article, conformance, operating requirements, support and ownership requirements, environmental requirements, and interface and operability requirements.
SCOPE
1.1 This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV CBC is a removable general purpose rigid wall enclosure that is mounted to the following model 5 ton cargo trucks: (1) the M923 Medium Tactical Vehicle (MTV) and (2) the M1083 MTV. It also can be mounted on the M1095 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E2518 −11
Standard Specification for
Cargo Bed Cover, Type IV (M923, 5 Ton Cargo Truck/M1083,
5 Ton Medium Tactical Vehicle (MTV)/ M1082, 5 Ton MTV
1
Trailer)
This standard is issued under the fixed designation E2518; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope 2.2 Federal Standards:
FED-STD-595Colors Used in Government Procurement
1.1 This specification covers the general requirements for
4
2.3 Military Standards:
the Type IV Cargo Bed Cover (CBC). The Type IV CBC is a
MIL-STD-209Slinging and Tiedown Provisions for Lifting
removablegeneralpurposerigidwallenclosurethatismounted
and Tying Down Military Equipment
to the following model 5 ton cargo trucks: (1) the M923
MIL-STD-810Environmental Test Methods and Engineer-
Medium Tactical Vehicle (MTV) and (2) the M1083 MTV. It
ing Guidelines
also can be mounted on the M1095 5 Ton MTV Trailer. The
MIL-STD-1366Transportability Criteria
CBC provides environmental protection and security for mis-
MIL-STD-1472Design Criteria: Human Engineering
sion equipment and items of general transport.
MIL-DTL-53039Coating, Aliphatic Polyurethane, Single
Component, Chemical Agent Resistant
1.2 The values stated in inch-pound units are to be regarded
MIL-DTL-53072 Chemical Agent Resistant Coating
asstandard.Nootherunitsofmeasurementareincludedinthis
(CARC)SystemApplicationProceduresandQualityCon-
standard.
trol Inspection
1.3 The following safety hazards caveat pertains only to the
4
2.4 Military Handbooks:
test required portion, Section 4, of this specification: This
MIL-HDBK-759Human Engineering Design
standard does not purport to address all of the safety concerns,
MIL-HDBK-1791Designing for Internal Aerial Delivery in
if any, associated with its use. It is the responsibility of the user
Fixed Winged Aircraft
of this standard to establish appropriate safety and health
5
2.5 OSHA Documents:
practicesanddeterminetheapplicabilityofregulatoryrequire-
Title 29 CFR 1910
ments prior to use.
6
2.6 ACGIH Documents:
ACGIHThreshold Limit Values
2. Referenced Documents
2
2.1 ASTM Standards:
3. General Requirements
E1925Specification for Engineering and Design Criteria for
3.1 First Article—When specified (see 6.2), a sample shall
Rigid Wall Relocatable Structures
besubjectedtofirstarticleinspectioninaccordancewith4.1.1.
F501Test Method for Aerospace Materials Response to
A first article is defined as a pre-production or an initial
Flame, with Vertical Test Specimen (for Aerospace Ve-
production sample consisting of one or more of each type of
3
hicles Standard Conditions) (Withdrawn 1998)
completed CBC.
3.2 Conformance—Items furnished under this specification
shall be subjected to conformance inspection in accordance
1
This specification is under the jurisdiction of ASTM Committee E06 on
with 4.1.2.
Performance of Buildings and is the direct responsibility of Subcommittee E06.53
on Materials and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Sept. 1, 2011. Published October 2011. Originally
4
approved in 2006. Last previous edition approved in 2006 as E2518–06. DOI: Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
10.1520/E2518-11. Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or www.dodssp.daps.mil.
5
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Occupational Safety and Health Administration (OSHA), 200
Standards volume information, refer to the standard’s Document Summary page on Constitution Ave., NW, Washington, DC 20210, http://www.osha.gov.
6
the ASTM website. Available from American Conference of Governmental Industrial Hygienists,
3
The last approved version of this historical standard is referenced on Inc. (ACGIH), 1330 Kemper Meadow Dr., Suite 600, Cincinnati, OH 45240,
www.astm.org. http://www.acgih.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E2518−11
3.3 Operating Requirements—Unless otherwise specified, through the cargo area. The vents shall prevent intrusion of
the Type IV CBC shall meet the following operating require- driven rain and have provisions for blackout. Vents shall be
ments in both the height extended and height retracted con- capable of providing ventilation when the vehicle is both
figurations. stationary and on the move. Vents requiring operation shall be
capable of being operated manually.The interior surface of the
3
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E2518–06 Designation: E2518 – 11
Standard Specification for
Cargo Bed Cover, Type IV (M923, 5 Ton Cargo Truck/M1083,
5 Ton Medium Tactical Vehicle (MTV)/ M1082, 5 Ton MTV
1
Trailer)
This standard is issued under the fixed designation E2518; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV Cargo Bed Cover
is a removable general purpose rigid enclosure for the cargo bed of the M923, 5Ton CargoTruck/M1083, 5Ton MediumTactical
Vehicle (MTV)/M1095, 5 Ton MTVTrailer. The CBC provides environmental protection and security for mission equipment and
items of general transport.
1.1 This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV CBC is a
removable general purpose rigid wall enclosure that is mounted to the following model 5 ton cargo trucks: (1) the M923 Medium
Tactical Vehicle (MTV) and (2) the M1083 MTV. It also can be mounted on the M1095 5 Ton MTV Trailer. The CBC provides
environmental protection and security for mission equipment and items of general transport.
1.2 Thevaluesstatedininch-poundunitsaretoberegardedasthestandard.Thevaluesgiveninparenthesisareforinformation
only. The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to
use.
2. Referenced Documents
2
2.1 ASTM Standards:
E1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
F501 Test Method forAerospace Materials Response to Flame, with Vertical Test Specimen (ForAerospace Vehicles Standard
3
Conditions)
4
2.2 Federal Standard:Federal Standards:
FED-STD-595 Colors Used in Government Procurement
4
2.3 Military Standards:
MIL-STD-209 Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment
MIL-STD-810 Environmental Test Methods and Engineering Guidelines
MIL-STD-1366 Transportability Criteria
MIL-STD-1472 Design Criteria: Human Engineering
MIL-DTL-53039 Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant
MIL-DTL-53072 Chemical Agent Resistant Coating (CARC) System Application Procedures and Quality Control Inspection
4
2.4 Military Handbook: Military Handbooks:
MIL-HDBK-759 Human Engineering Design
MIL-HDBK-1791 Designing for Internal Aerial Delivery in Fixed Winged Aircraft
1
This specification is under the jurisdiction ofASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.53 on Materials
and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Oct. 1, 2006. Published October 2006. DOI: 10.1520/E2518-06.
Current edition approved Sept. 1, 2011. Published October 2011. Originally approved in 2006. Last previous edition approved in 2006 as E2518–06. DOI:
10.1520/E2518-11.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
E2518 – 11
5
2.5 OSHA Documents:
Occupational Safety and Health Act(OSHA), Title 29 CFR 1910 Title 29 CFR 1910
6
2.6 The American Conference of Governmental Industrial Hygienists (ACGIH): ACGIH Documents:
ACGIH Threshold Limit Values ACGIH Threshold Limit Values
3. General Requirements
3.1 First Article—When specified (see 6.2), a sample shall be subjected to first article
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.