EN ISO 14122-2:2001

Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2001)

This standard applies to all machinery (stationary and mobile) where fixed means of access are necessary. This standard applies to working platforms and walkways which are an integral part of a machine. This standard could also apply to working platforms and walkways to that part of the building where the machine is installed, providing the main function of that part of the building is to provide a means of access to the machine. NOTE: This standard may be used in other conditions of use, but to respect the National regulations.

Sicherheit von Maschinen - Ortsfeste Zugänge zu maschinellen Anlagen - Teil 2: Arbeitsbühnen und Laufstege (ISO 14122-2:2001)

Diese Norm gilt für alle Maschinen (stationäre und mobile), für die orstfeste Zugänge erforderlich sind. Diese Norm gilt für Arbeitsbühnen und Laufstege, die Bestandteil einer Maschine sind. Diese Norm kann auch für Arbeitsbühnen und Laufstege angewendet werden, die Teil des Gebäudes sind, in dem die Maschine aufgestellt ist, wobei die Hauptfunktion dieses Gebäudeteils darin besteht, den Zugang zu der Maschine zu ermöglichen. ANMERKUNG: Diese Norm darf auch unter anderen Einsatzbedingungen angewendet werden, jedoch unter Beachtung der nationalen Vorschriften.

Sécurité des machines - Moyens d'accès permanents aux machines - Partie 2: Plates-formes de travail et passerelles (ISO 14122-2:2001)

L'ISO 14122 définit les prescriptions générales de sécurité d'accès aux machines mentionnées dans l'EN 292-2. La partie 1 de l'ISO 14122 donne des recommandations concernant le choix approprié des moyens d'accès lorsque l'accès nécessaire à la machine n'est pas directement possible à partir du niveau du sol ou d'un plancher. La présente partie de l'ISO 14122 s'applique à toutes les machines (fixes ou mobiles) où des moyens d'accès fixes sont nécessaires. La présente partie de l'ISO 14122 s'applique aux plates-formes de travail et aux passerelles qui sont partie intégrante d'une machine. La présente partie de l'ISO 14122 peut s'appliquer également aux plates-formes de travail et aux passerelles donnant accès aux parties du bâtiment où la machine est installée, à condition que la fonction principale de cette partie du bâtiment soit de donner accès à la machine.
NOTE La présente partie de l'ISO 14122 peut être utilisée également pour les moyens d'accès qui sont hors du domaine d'application de la présente partie de l'ISO 14122. Dans ce cas, il convient de tenir compte des éventuelles réglementations nationales ou autres. La présente partie de l'ISO 14122 s'applique également aux plates-formes de travail et aux passerelles spécifiques à la machine qui ne sont pas fixées de façon permanente sur la machine et qui peuvent être démontées ou déplacées sur le côté pour certaines opérations sur la machine (par exemple pour changer les outils d'une grande presse). La présente partie de l'ISO 14122 ne s'applique pas aux ascenseurs ou aux plates-formes élévatrices mobiles spécialement conçues pour soulever les personnes ou aux autres dispositifs spécifiques.

Varnost strojev - Stalni dostopi do strojev in postrojenj - 2. del: Delovne ploščadi in podesti (ISO 14122-2:2001)

Velja za stroje (stacionarne in mobilne), kadar so potrebni fiksni načini dostopa. Ta standard velja za stopnišča, stopničaste lestve in varovalne ograje, ki so sestavni del stroja.

General Information

• Status: Withdrawn
• Publication Date: 14-May-2001
• Withdrawal Date: 21-Jun-2016
• ICS: 13.110 - Safety of machinery
• Technical Committee: CEN/TC 114 - Safety of machinery
• Drafting Committee: CEN/TC 114 - Safety of machinery
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 22-Jun-2016
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
• Ref Project: SIST EN ISO 14122-2:2002 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2001)

Relations

• Replaced By: EN ISO 14122-2:2016 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
• Effective Date: 29-Jun-2016
• Amended By: EN ISO 14122-2:2001/A1:2010 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways - Amendment 1 (ISO 14122-2:2001/Amd 1:2010)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2002
9DUQRVWVWURMHY6WDOQLGRVWRSLGRVWURMHYLQSRVWURMHQMGHO'HORYQHSORãþDGL
LQSRGHVWL,62
Safety of machinery - Permanent means of access to machinery - Part 2: Working
platforms and walkways (ISO 14122-2:2001)
Sicherheit von Maschinen - Ortsfeste Zugänge zu maschinellen Anlagen - Teil 2:
Arbeitsbühnen und Laufstege (ISO 14122-2:2001)
Sécurité des machines - Moyens d'acces permanents aux machines - Partie 2: Plates-
formes de travail et passerelles (ISO 14122-2:2001)
Ta slovenski standard je istoveten z: EN ISO 14122-2:2001
ICS:
13.110 Varnost strojev Safety of machinery
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 14122-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2001
ICS 13.110
English version
Safety of machinery - Permanent means of access to machinery
- Part 2: Working platforms and walkways (ISO 14122-2:2001)
Sécurité des machines - Moyens d'accès permanents aux Sicherheit von Maschinen - Ortsfeste Zugänge zu
machines - Partie 2: Plates-formes de travail et passerelles maschinellen Anlagen - Teil 2: Arbeitsbühnen und
(ISO 14122-2:2001) Laufstege (ISO 14122-2:2001)
This European Standard was approved by CEN on 14 February 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14122-2:2001 E
worldwide for CEN national Members.

Page 2
Contents
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions.6
4 General requirements.6
4.1 General.6
4.1.1 Construction and materials .6
4.1.2 Safety of operators .7
4.2 Specific requirements .7
4.2.1 Location .7
4.2.2 Dimensions.7
4.2.3 Facilities or equipment.8
4.2.4 Floorings.8
4.2.5 Design loads.10
5 Assembly instructions .10
Annex A (informative) Different methods of determining levels of slip-resistance .11
Annex ZA (informative) Relationship of this European standard with EC Directives.12
Bibliography .13

Page 3
Foreword
The text of EN ISO 14122-2:2001 has been prepared by Technical Committee CEN/TC 114 "Safety of machinery",
the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 199 "Safety of
machinery".
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by November 2001, and conflicting national standards shall be withdrawn at the latest
by November 2001.
This European Standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.

Page 4
Introduction
EN ISO 14122 consists of the following parts, under the general title "Safety of machinery - Permanent means of
access to machinery" :
Part 1 : Choice of a fixed means of access between two levels
Part 2 : Working platforms and walkways
Part 3 : Stairs, stepladders and guard-rails
Part 4 : Fixed ladders.
This part of EN ISO 14122 is a type B standard as stated in EN 1070.
This document is to be read in conjunction with clause 1.6.2 "Access to operating position and servicing points"
and 1.5.15 "Risk of slipping, tripping or falling" of the essential safety requirements expressed in annex A of
EN 292-2:1991/A1:1995. See also 6.2.4 "Provision for safe access to machinery" of EN 292-2:1991.
For the significant hazards covered by this standard, see clause 4 of EN ISO 14122-1.
The provisions of this document may be supplemented or modified by a type C standard.
NOTE 1 For machines which are covered by the scope of a type C standard and which have been designed and built
according to the provisions of that standard, the provisions of that type C standard take precedence over the provisions of this
type B standard.
The dimensions specified are consistent with established ergonomic data given in EN 547-3 "Safety of machinery - Human body
dimensions – Part 3 : Anthropometric data".
NOTE 2 The use of materials other than metals (composite materials, so-called "advanced" materials, etc.) does not alter the
application of the present standard.
Annexes A and ZA are for information only.
This part of EN ISO 14122 contains a Bibliography.

Page 5
1 Scope
EN ISO 14122 defines the general requirements for safe access to machines mentioned in EN 292-2. Part 1 of EN
ISO 14122 gives advice about the correct choice of access means when the necessary access to the machine is
not possible directly from the ground level or from a floor.
This part of EN ISO 14122 applies to all machinery (stationary and mobile) where fixed means of access are
necessary.
This part of EN ISO 14122 applies to working platforms and walkways which are a part of a machine.
This part of EN ISO 14122 may also apply to working platforms and walkways to that part of the building where the
machine is installed, providing the main function of that part of the building is to provide a means of access to the
machine.
NOTE This part of EN ISO 14122 may be used also for means of access which are outside the scope of this standard. In
those cases the possible relevant national or other regulations should be taken into account.
This part of EN ISO 14122 applies also to working platforms and walkways specific to the machine which are not
permanently fixed to the machine and which may be removed or moved to the side for some operations of the
machine (e.g. changing tools in a large press).
This part of EN ISO 14122 does not apply to lifts, to moveable elevating platforms or other devices specially
designed to lift persons between two levels.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 292—1 (ISO/TR 12100-1), Safety of machinery — Basic concepts, general principles for design — Part 1 :
Basic terminology, methodology
EN 292-2/A1 (ISO/TR 12100-2), Safety of machinery — Basic concepts, general principles for design — Part 2 :
Technical principles and specifications
EN 294 (ISO 13852), Safety of machinery — Safety distances to prevent danger zones being reached by the upper
limbs
EN 547-1, Safety of machinery — Human body dimensions — Part 1 : Principles for determining the dimensions
required for openings for whole body access into machinery
EN 547-2, Safety of machinery — Human body dimensions — Part 2 : Principles for determining the dimensions
required for access openings
EN 547-3, Safety of machinery — Human body dimensions — Part 3 : Anthropometric data
EN 1070, Safety of machinery — Terminology

Page 6
EN ISO 14122-1, Safety of machinery — Permanents means of access to machinery — Part 1 : Choice of fixed
means of access between two levels
EN ISO 14122-3:2001, Safety of machinery — Permanents means of access to machinery — Part 3 : Stairs,
stepladders and guard-rails
3 Terms and definitions
For the purposes of this part of EN ISO 14122, the terms and definitions stated in EN 1070 "Safety of machinery -
Terminology" and of EN ISO 14122-1 apply.
The following additional definitions particularly required for this standard apply :
3.1
flooring
assembly of elements making up the floor of a walkway or a working platform and being in direct contact with
footwear
3.2
walkway
level surface used for moving from one point to another
3.3
working platform
level surface used for the operation, maintenance, inspection, repair, sampling and other phases of work in
connection with the machinery
3.4
slip resistant surface
flooring surface designed for improving the grip of footwear
4 General requirements
Walkways and working platforms shall comply with the following general safety requirements:
4.1 General
The working platforms and walkways shall be designed, constructed, located and where necessary protected so
that the operators are safe when having access to the working platforms and when they are on them for the
operation, setting, monitoring, repairing or any other work involved with the machinery.
4.1.1 Construction and materials
Working platforms and walkways shall be designed and constructed and the materials selected so that they
withstand the foreseeable conditions of use. In particular, at least the following details shall be considered:
a) dimensioning and selection of components (including fixings, connections, supports and foundations) to
ensure sufficient rigidity and stability;
b) resistance of all parts to environmental effects (such as climate, chemical agents, corrosive gases) e.g. by the
use of a corrosion resistant material or with the aid of a suitable protective coating;
c) positioning of constructional elements so that water cannot be accumulated e.g. in the joints;
d) use of compatible materials e.g. to minimise galvanic action or differential thermal expansion;
e) dimension of walkways and working platforms shall be according to available anthropometric data (see 4.2.2 of
this standard, see also EN 547-1 and EN 547-3);

Page 7
f) walkways and working platforms shall be designed and constructed to prevent the hazards due to falling
objects. For guard-rails and toe plates, see clause 7 of EN ISO 14122-3:2001 and for openings in the flooring, see
4.2.4.4 of this standard;
g) the removal of any part of the machine shall, as far as practicable, be possible without removing guard-rails,
pieces of flooring or other permanent protective barriers.
4.1.2 Safety of operators
Walkways and working platforms shall be designed and constructed so that they are safe to use. In particular, the
following details shall at least be considered:
a) all parts likely to be in contact with operators shall be designed and built in such a way that the operator is
safe-guarded agai
...