Gas-fired overhead radiant strip heaters and multi-burner continuous radiant tube heater systems for non-domestic use - Safety and energy efficiency

This document specifies the requirements and test methods for the construction, safety, classification, marking and efficiency of non-domestic gas-fired overhead radiant strips heaters and multi-burner continuous radiant tube heater systems (referred to in the body of the text as the “system”) with each burner unit under the control of an automatic burner control system.
For radiant strip heaters incorporating a single burner, this standard is applicable to Type B22, B23, B52, B53, C12, C13, C32, C33 C52 and C53 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means.
For multi-burner continuous radiant tube heater systems this standard is applicable to type B22, B52, and C52 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means.
This standard also includes appliances incorporating a secondary heat exchanger in the flue system.
This standard is not applicable to:
a)   appliances designed for use in domestic dwelling;
b)   outdoor appliances;
c)   radiant strip heaters where the heat input is in excess of  300 KW (based on the net calorific value of the appropriate reference test gas);
d)   continuous radiant tube heater systems where the heat input of any individual burner unit is in excess of 70 kW (based on the net calorific value of the appropriate reference test gas);
e)   appliances having combustion products evacuation ducts that are non-metallic in the flue system – except ducts downstream of a possible additional condensing exhaust gas heat exchanger.
In addition, for heater systems incorporating multiple tube heaters this standard is not applicable to:
f)        appliances that are designed for continuous condensation within the flue system under normal      operating conditions – except downstream a possible additional exhaust gas heat exchanger.
This standard is applicable to appliances which are intended to be type tested.

Gasbefeuerte Dunkelstrahler-Wärmebänder und kontinuierliche Mehr-Brenner-Dunkelstrahlersysteme für gewerbliche und industrielle Anwendungen - Sicherheit und Energieeffizienz

Dieses Dokument legt die Anforderungen und Prüfverfahren für den Bau, die Sicherheit, die Klassifizierung, die Kennzeichnung und die Effizienz von gasbefeuerten Bandheizstrahlern und Mehr-Brenner-Dunkelstrahlersystemen für gewerbliche und industrielle Anwendungen fest (im Haupttext als „Geräte“ bezeichnet), bei denen jede Brennereinheit durch einen Gasfeuerungsautomaten gesteuert wird.
Für Bandheizstrahler mit einem einzelnen Brenner gilt diese Norm für Geräte des Typs B22, B23, B52, B53, C12, C13, C32, C33 C52 und C53 für gewerbliche und industrielle Anwendungen, bei denen die Zufuhr der Verbrennungsluft und/oder die Abfuhr von Verbrennungsprodukten auf mechanische Weise erfolgt.
Für durchgehende Mehr-Brenner-Dunkelstrahlersysteme gilt diese Norm für Geräte des Typs B22, B52 und C52 für gewerbliche und industrielle Anwendungen, bei denen die Zufuhr der Verbrennungsluft und/oder die Abfuhr von Verbrennungsprodukten auf mechanische Weise erfolgt.
Diese Norm gilt außerdem für Geräte, die mit einer sekundären Abgasabführung im Abgassystem ausgestattet sind.
Diese Europäische Norm gilt nicht für:
a) Geräte, die für eine Verwendung in Wohnungen gedacht sind;
b) Geräte, die für eine Verwendung im Freien gedacht sind;
c) Bandheizstrahler mit einer Wärmebelastung über 300 kW (bezogen auf den Heizwert des jeweiligen Normprüfgases);
d) Durchgehende Dunkelstrahlersysteme mit einer Wärmebelastung der einzelnen Brennereinheit von mehr als 70 kW (bezogen auf den Brennwert des jeweiligen Normprüfgases);
e) Geräte mit nichtmetallischen Abgasabführungsleitungen im Abgasabführungssystem – außer Leitungen hinter einem möglichen zusätzlichen kondensierenden Abgaswärmetauscher.
Darüber hinaus gilt diese Norm im Fall von Wärmeerzeugersystemen mit mehreren Rohrwärmeerzeugern nicht für:
f) Geräte, die für eine dauerhafte Kondensation im Abgassystem unter Normalbetriebsbedingungen ausgelegt sind – außer hinter einem möglichen zusätzlichen Abgaswärmetauscher.
Diese Norm ist anwendbar für Geräte, die für eine Typprüfung vorgesehen sind.

Bandes radiantes et systèmes à tubes radiants continus à brûleurs multiples suspendus à usage non domestique utilisant les combustibles gazeux - Sécurité et efficacité énergétique

Le présent document définit les exigences et les méthodes d’essai relatives à la construction, la sécurité, la classification, le marquage et l’utilisation rationnelle de l’énergie des bandes radiantes et systèmes à tubes radiants continus à brûleurs multiples suspendus à usage non domestique utilisant les combustibles gazeux (appelés dans le corps du texte le « système »), chaque unité de combustion étant équipé d’un système automatique de commande et de sécurité.
Pour les bandes radiantes comprenant un brûleur unique, la présente norme s’applique aux appareils de type B22, B23, B52, B53, C12, C13, C32, C33 C52 et C53 destinés à être utilisés ailleurs que dans des locaux domestiques où l’arrivée en air comburant et/ou l’évacuation des produits de combustion est/sont assurée(s) par des moyens mécaniques.
Pour les systèmes à tubes radiants continus à brûleurs multiples, la présente norme s’applique aux tubes de types B22, B52, et C52 destinés à être utilisés ailleurs que dans des locaux domestiques où l’arrivée en air comburant et/ou l’évacuation des produits de combustion est/sont assurée(s) par des moyens mécaniques.
Le présent document couvre également des appareils comprenant un échangeur de chaleur secondaire dans le système d’évacuation des produits de combustion.
Le présent document ne s’applique pas :
a)   aux appareils conçus pour des locaux domestiques ;
b)   aux appareils utilisés en plein air ;
c)   aux bandes radiantes dont la puissance calorifique nominale dépasse 300 kW (sur le pouvoir calorifique inférieur du gaz de référence approprié) ;
d)   aux systèmes à tubes radiants continus dont le débit calorifique de chaque unité de combustion dépasse 70 kW (sur le pouvoir calorifique inférieur du gaz de référence approprié) ;
e)   aux appareils équipés de conduits d’évacuation des produits de combustion non métalliques, à l’exception des conduits en aval d’un éventuel échangeur de chaleur des produits de combustion à condensation.
De plus, pour les systèmes de chauffage comprenant plusieurs tubes, la présente norme ne s’applique pas :
f)   aux appareils conçus pour une condensation continue dans le système d’évacuation des produits de combustion dans des conditions de fonctionnement normales, sauf en aval d’un éventuel échangeur de chaleur des produits de combustion.
Le présent document s’applique aux appareils qui sont destinés à subir des essais de type.

Stropna plinska linijska sevala in cevna sevala z več plinskimi gorilniki za gretje nestanovanjskih prostorov - Varnost in energijska učinkovitost

Ta dokument določa zahteve in preskusne metode za izdelavo, varnost, razvrščanje, označevanje in učinkovitost stropnih plinskih linijskih seval in cevnih seval z več plinskimi gorilniki za gretje nestanovanjskih prostorov (v jedru besedila imenovanih »sistem«), pri čemer je vsaka enota gorilnika pod nadzorom avtomatskega sistema za upravljanje gorilnikov.
Za sevalne grelne linije, ki vsebujejo en gorilnik, se ta standard uporablja za aparate tipa B22, B23, B52, B53, C12, C13, C32, C33, C52 in C53, namenjene za uporabo v nestanovanjskih prostorih, v katerih se dovajanje zgorevalnega zraka in/ali odvajanje produktov zgorevanja doseže z mehanskimi sredstvi.
Za cevna sevala z več plinskimi gorilniki za gretje se ta standard uporablja za aparate tipa B22, B52 in C52, namenjene za uporabo v nestanovanjskih prostorih, v katerih se dovajanje zgorevalnega zraka in/ali odvajanje produktov zgorevanja doseže z mehanskimi sredstvi. Ta standard vključuje tudi aparate, ki imajo v dimniškem sistemu vgrajene sekundarne izmenjevalnike toplote.
Ta standard se ne uporablja za:
a) aparate, zasnovane za uporabo v stanovanjskih prostorih;
b) aparate za uporabo na prostem;
c) sevalne grelne linije, pri katerih nazivna moč presega 300 kW (na podlagi neto kalorične vrednosti ustreznega referenčnega preskusnega plina);
d) cevna sevala, pri katerih nazivna moč katerega koli posameznega gorilnika presega 70 kW (na podlagi neto kalorične vrednosti ustreznega referenčnega preskusnega plina);
e) aparate s cevmi za odvajanje produktov zgorevanja v dimniškem sistemu, ki so nekovinske, razen če so cevi v smeri toka za morebitnim dodatnim kondenzacijskim toplotnim izmenjevalnikom izpušnih plinov.
Prav tako se ne uporablja za grelne sisteme, ki vsebujejo več cevnih grelnikov:
f) aparate, ki so zasnovani za stalno kondenzacijo v dimniškem sistemu pri običajnih delovnih pogojih, razen če so v smeri toka za morebitnim dodatnim kondenzacijskim toplotnim izmenjevalnikom izpušnih plinov.
Ta standard se uporablja za aparate, predvidene za tipski preskus.

General Information

Status
Published
Publication Date
08-Oct-2019
Withdrawal Date
29-Apr-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
09-Oct-2019
Due Date
09-Apr-2019
Completion Date
09-Oct-2019

Relations

Buy Standard

Standard
EN 17175:2020 - BARVE
English language
162 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN 17175:2020 - BARVE na PDF-str 130
English language
162 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN 416-1:2009
SIST EN 416-2:2006
SIST EN 777-4:2009
Stropna plinska linijska sevala in cevna sevala z več plinskimi gorilniki za gretje
nestanovanjskih prostorov - Varnost in energijska učinkovitost
Gas-fired overhead radiant strip heaters and multi-burner continuous radiant tube heater
systems for non-domestic use - Safety and energy efficiency
Gasbefeuerte Strahlungsheizstreifen und Dunkelstrahlersysteme mit mehreren Brennern
für gewerbliche und industrielle Anwendungen - Sicherheit und Energieeffizienz
Bandes radiantes et systèmes à tubes radiants continus à brûleurs multiples suspendus
à usage non domestique utilisant les combustibles gazeux - Sécurité et efficacité
énergétique
Ta slovenski standard je istoveten z: EN 17175:2019
ICS:
97.100.20 Plinski grelniki Gas heaters
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17175
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 97.100.20 Supersedes EN 416-1:2009, EN 416-2:2006, EN 777-
4:2009
English Version
Gas-fired overhead radiant strip heaters and multi-burner
continuous radiant tube heater systems for non-domestic
use - Safety and energy efficiency
Bandes radiantes et systèmes à tubes radiants continus Gasbefeuerte Strahlungsheizstreifen und
à brûleurs multiples suspendus à usage non Dunkelstrahlersysteme mit mehreren Brennern für
domestique utilisant les combustibles gazeux - Sécurité gewerbliche und industrielle Anwendungen -
et efficacité énergétique Sicherheit und Energieeffizienz
This European Standard was approved by CEN on 26 August 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17175:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and symbols . 9
4 Classification of appliances . 28
5 Constructional requirements . 30
6 Operational requirements . 45
7 Energy Efficiency . 77
8 Requirements of energy efficiency (rational use of energy) . 89
9 Risk assessment . 93
10 Marking and instructions . 93
Annex A (informative) National situations . 101
A.1 General . 101
A.1.1 Categories . 101
A.1.2 Gas rate adjusters, aeration adjusters and regulators . 101
A.1.3 Conversion to different gases . 101
A.2 Gas connections in the various countries . 101
A.3 Flue connections in the various countries . 103
Annex B (informative) Types of appliances . 104
B.1 Single burner overhead radiant strip heaters . 104
B.1.1 Type B appliances with a fan in the combustion circuit . 104
B.1.2 Type C appliances with a fan in the combustion circuit . 106
B.2 Multiple burner overhead continuous radiant tube heater systems - Type B or B
22 52
appliances with a fan in the combustion circuit . 109
Annex C (informative) Equivalence rules . 110
C.1 Conversion to categories within a restricted Wobbe Index range . 110
C.2 Conversion to categories within an identical Wobbe Index range . 110
C.3 Conversion to categories within a wider Wobbe Index range . 111
Annex D (informative) Calculation of the mass flow rate of flue gases . 112
D.1 Flue gas mass flow rate . 112
D.2 Quantity of air in the flue gas . 112
D.3 Flue gas excess air ratio (λ) . 112
D.4 Quantity of water vapour in the flue gas . 113
D.5 Quantity of Nitrogen in the flue gas . 113
D.6 Quantity of Oxygen in the flue gas . 113
D.7 Dry quantity of flue gas . 113
D.8 Quantity of carbon dioxide in the flue gas . 114
Annex E (informative) Identification of the types of gas in use in various countries . 115
Annex F (normative) Special national conditions . 117
Annex G (normative) Calculation of conversions of NO . 118
x
G.1 NO emission conversion factors . 118
x
G.2 NO Conversion — Calculation . 119
x
Annex H (informative) National situations of countries whose national bodies are CEN
associate members . 121
Annex I (informative) Different types of heat input control . 122
Annex J (informative) Radiometer design . 123
J.1 Principle radiometer design features . 123
J.2 Radiometer technical design . 124
J.3 Pyro-electric detector . 124
J.4 Ulbricht Sphere . 124
J.4.1 General . 124
J.4.2 Dimensions of the Ulbricht sphere . 125
J.4.3 Surface of the Ulbricht sphere. 125
J.4.4 Angular responsivity test of the Ulbricht sphere . 126
Annex K (informative)  Radiometer calibration . 127
K.1 Radiometer calibration . 127
K.2 Black body calibration equipment and procedure. 127
K.2.1 General . 127
K.2.2 Temperature calibration at reference condition . 128

K.2.3 Temperature calibration at higher temperatures . 129
K.2.4 Calibration calculation . 130
K.3 Calibration procedure in detail, presented as a worked example . 131
K.3.1 Calibration Measurements . 131
K.3.2 Selecting the average readings . 131
K.3.3 Determination of the 1/S sensitivity per temperature . 132
K.3.4 Determining the 1/S sensitivity of the radiometer . 132
K.3.5 Documentation of calibration results . 132
Annex L (normative)  Correction of measured radiant output for absorption by H O and CO . 136
2 2
L.1 General . 136
L.2 Calculation method . 138
Annex M (informative)  Radiant heat output data - Recording of results . 139
M.1 General information to be recorded . 139
M.1.1 Test and appliance data . 139
M.1.2 Radiometer technical data . 139
M.1.3 Measuring plane technical data . 139
M.2 Measurement results . 140
M.2.1 Test information . 140
M.2.2 Test ambient conditions . 140
M.2.3 Gas/heat input data .
...


SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN 416-1:2009
SIST EN 416-2:2006
SIST EN 777-4:2009
Stropna plinska linijska sevala in cevna sevala z več plinskimi gorilniki za gretje
nestanovanjskih prostorov - Varnost in energijska učinkovitost
Gas-fired overhead radiant strip heaters and multi-burner continuous radiant tube heater
systems for non-domestic use - Safety and energy efficiency
Gasbefeuerte Strahlungsheizstreifen und Dunkelstrahlersysteme mit mehreren Brennern
für gewerbliche und industrielle Anwendungen - Sicherheit und Energieeffizienz
Bandes radiantes et systèmes à tubes radiants continus à brûleurs multiples suspendus
à usage non domestique utilisant les combustibles gazeux - Sécurité et efficacité
énergétique
Ta slovenski standard je istoveten z: EN 17175:2019
ICS:
97.100.20 Plinski grelniki Gas heaters
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17175
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 97.100.20 Supersedes EN 416-1:2009, EN 416-2:2006, EN 777-
4:2009
English Version
Gas-fired overhead radiant strip heaters and multi-burner
continuous radiant tube heater systems for non-domestic
use - Safety and energy efficiency
Bandes radiantes et systèmes à tubes radiants continus Gasbefeuerte Strahlungsheizstreifen und
à brûleurs multiples suspendus à usage non Dunkelstrahlersysteme mit mehreren Brennern für
domestique utilisant les combustibles gazeux - Sécurité gewerbliche und industrielle Anwendungen -
et efficacité énergétique Sicherheit und Energieeffizienz
This European Standard was approved by CEN on 26 August 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17175:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and symbols . 9
4 Classification of appliances . 28
5 Constructional requirements . 30
6 Operational requirements . 45
7 Energy Efficiency . 77
8 Requirements of energy efficiency (rational use of energy) . 89
9 Risk assessment . 93
10 Marking and instructions . 93
Annex A (informative) National situations . 101
A.1 General . 101
A.1.1 Categories . 101
A.1.2 Gas rate adjusters, aeration adjusters and regulators . 101
A.1.3 Conversion to different gases . 101
A.2 Gas connections in the various countries . 101
A.3 Flue connections in the various countries . 103
Annex B (informative) Types of appliances . 104
B.1 Single burner overhead radiant strip heaters . 104
B.1.1 Type B appliances with a fan in the combustion circuit . 104
B.1.2 Type C appliances with a fan in the combustion circuit . 106
B.2 Multiple burner overhead continuous radiant tube heater systems - Type B or B
22 52
appliances with a fan in the combustion circuit . 109
Annex C (informative) Equivalence rules . 110
C.1 Conversion to categories within a restricted Wobbe Index range . 110
C.2 Conversion to categories within an identical Wobbe Index range . 110
C.3 Conversion to categories within a wider Wobbe Index range . 111
Annex D (informative) Calculation of the mass flow rate of flue gases . 112
D.1 Flue gas mass flow rate . 112
D.2 Quantity of air in the flue gas . 112
D.3 Flue gas excess air ratio (λ) . 112
D.4 Quantity of water vapour in the flue gas . 113
D.5 Quantity of Nitrogen in the flue gas . 113
D.6 Quantity of Oxygen in the flue gas . 113
D.7 Dry quantity of flue gas . 113
D.8 Quantity of carbon dioxide in the flue gas . 114
Annex E (informative) Identification of the types of gas in use in various countries . 115
Annex F (normative) Special national conditions . 117
Annex G (normative) Calculation of conversions of NO . 118
x
G.1 NO emission conversion factors . 118
x
G.2 NO Conversion — Calculation . 119
x
Annex H (informative) National situations of countries whose national bodies are CEN
associate members . 121
Annex I (informative) Different types of heat input control . 122
Annex J (informative) Radiometer design . 123
J.1 Principle radiometer design features . 123
J.2 Radiometer technical design . 124
J.3 Pyro-electric detector . 124
J.4 Ulbricht Sphere . 124
J.4.1 General . 124
J.4.2 Dimensions of the Ulbricht sphere . 125
J.4.3 Surface of the Ulbricht sphere. 125
J.4.4 Angular responsivity test of the Ulbricht sphere . 126
Annex K (informative)  Radiometer calibration . 127
K.1 Radiometer calibration . 127
K.2 Black body calibration equipment and procedure. 127
K.2.1 General . 127
K.2.2 Temperature calibration at reference condition . 128

K.2.3 Temperature calibration at higher temperatures . 129
K.2.4 Calibration calculation . 130
K.3 Calibration procedure in detail, presented as a worked example . 131
K.3.1 Calibration Measurements . 131
K.3.2 Selecting the average readings . 131
K.3.3 Determination of the 1/S sensitivity per temperature . 132
K.3.4 Determining the 1/S sensitivity of the radiometer . 132
K.3.5 Documentation of calibration results . 132
Annex L (normative)  Correction of measured radiant output for absorption by H O and CO . 136
2 2
L.1 General . 136
L.2 Calculation method . 138
Annex M (informative)  Radiant heat output data - Recording of results . 139
M.1 General information to be recorded . 139
M.1.1 Test and appliance data . 139
M.1.2 Radiometer technical data . 139
M.1.3 Measuring plane technical data . 139
M.2 Measurement results . 140
M.2.1 Test information . 140
M.2.2 Test ambient conditions . 140
M.2.3 Gas/heat input data .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.