iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 573-3:2019+A2:2023

(Main)

Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products

Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 3: Chemische Zusammensetzung und Erzeugnisformen

Aluminium et alliages d'aluminium - Composition chimique et forme des produits corroyés - Partie 3 : Composition chimique et forme des produits

Le présent document spécifie les limites de composition chimique des aluminiums et alliages d’aluminium corroyés et les formes de produits.
NOTE   Les limites de composition chimique de l’aluminium et des alliages d’aluminium spécifiées ici sont strictement identiques à celles enregistrées auprès de l’Aluminium Association, 1525 Wilson Boulevard, Suite 600, Arlington, VA 22209, États-Unis, pour les alliages correspondants.

Aluminij in aluminijeve zlitine - Kemična sestava in oblika gnetenih izdelkov - 3. del: Kemična sestava in oblika izdelkov (vključno z dopolnilom A2)

General Information

Status
Published
Publication Date
19-Dec-2023
ICS
77.120.10 - Aluminium and aluminium alloys
Technical Committee
CEN/TC 132 - Aluminium and aluminium alloys
Drafting Committee
CEN/TC 132/WG 5 - Extruded and drawn products
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Dec-2023
Due Date
14-Feb-2025
Completion Date
20-Dec-2023
Ref Project
SIST EN 573-3:2019+A2:2024 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products

Relations

Merged From
EN 573-3:2019+A1:2022/prA2 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
Effective Date
25-Oct-2023
Merged From
EN 573-3:2019+A1:2022 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
Effective Date
25-Oct-2023

Buy Standard

EN 573-3:2019+A2:2024EN 573-3:2019+A2:2024
PreviousNext
Standard
EN 573-3:2019+A2:2024
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 573-3:2019+A2:2024
01-maj-2024
Aluminij in aluminijeve zlitine - Kemična sestava in oblika gnetenih izdelkov - 3.
del: Kemična sestava in oblika izdelkov (vključno z dopolnilom A2)
Aluminium and aluminium alloys - Chemical composition and form of wrought products -
Part 3: Chemical composition and form of products
Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von
Halbzeug - Teil 3: Chemische Zusammensetzung und Erzeugnisformen
Aluminium et alliages d'aluminium - Composition chimique et forme des produits
corroyés - Partie 3 : Composition chimique et forme des produits
Ta slovenski standard je istoveten z: EN 573-3:2019+A2:2023
ICS:
77.040.30 Kemijska analiza kovin Chemical analysis of metals
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 573-3:2019+A2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 573-3:2019+A2:2024

---------------------- Page: 2 ----------------------
SIST EN 573-3:2019+A2:2024


EN 573-3:2019+A2
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2023
EUROPÄISCHE NORM
ICS 77.120.10 Supersedes EN 573-3:2019+A1:2022
English Version

Aluminium and aluminium alloys - Chemical composition
and form of wrought products - Part 3: Chemical
composition and form of products
Aluminium et alliages d'aluminium - Composition Aluminium und Aluminiumlegierungen - Chemische
chimique et forme des produits corroyés - Partie 3 : Zusammensetzung und Form von Halbzeug - Teil 3:
Composition chimique et forme des produits Chemische Zusammensetzung und Erzeugnisformen
This European Standard was approved by CEN on 31 January 2022 and includes Amendment approved by CEN on 17 November
2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 573-3:2019+A2:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 573-3:2019+A2:2024
EN 573-3:2019+A2:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Chemical composition limits . 6
5 Writing rules . 6
6 Alloy designations . 7
7 Sequence of elements . 7
8 Rounding rules for determination of compliance . 7
Annex A (normative) Form of products . 32
A.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 683-2:2024(Main)
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
SIST EN 683-2:2024

This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy finstock.
The chemical composition limits of these materials are specified in EN 573 3, unless otherwise agreed between supplier and purchaser.
The designations of wrought aluminium and wrought aluminium alloys and the temper designations used in this document are specified in EN 573 3, and the temper designations are defined in EN 515.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14242:2023(Main)
Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission spectrometric analysis
SIST EN 14242:2023

This document specifies an inductively coupled plasma optical emission spectrometric method
(ICP-OES) for the analysis of aluminium and aluminium alloys.
This method is applicable to the determination of silicon, iron, copper, manganese, magnesium, chromium, nickel, zinc, titanium, gallium, vanadium, beryllium, bismuth, calcium, cadmium, cobalt, lithium, sodium, lead, antimony, tin, strontium and zirconium in aluminium and aluminium alloys.
The content of the elements to be determined should be at least 10 times higher than the corresponding detection limits.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1676:2020(Main)
Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications
SIST EN 1676:2020

This document defines the requirements for grades of alloyed aluminium ingots intended for remelting.
It specifies the classifications and designations applicable to these grades, the conditions in which they are produced, their properties and the marks by which they are identified.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14726:2019(Main)
Aluminium and aluminium alloys - Determination of the chemical composition of aluminium and aluminium alloys by spark optical emission spectrometry
SIST EN 14726:2019

This document describes the criteria and the procedure for analysing aluminium and aluminium alloys with spark optical emission spectrometry (S-OES). The scope of this document covers the following:
-   sample preparation;
-   operational guidelines for an optical emission spectrometer (including maintenance);
-   traceability of the analytical results to the International System of units: mass (kg);
-   assessing the uncertainty associated with each analytical result.
This document refers to simultaneous spark emission spectrometers for the analysis of solid samples.
It applies to the determination of silicon, iron, copper, manganese, magnesium, chromium, nickel, zinc, titanium, boron, gallium, vanadium, beryllium, bismuth, calcium, cadmium, cobalt, lithium, sodium, phosphorus, lead, antimony, tin, strontium and zirconium in aluminium and aluminium alloys.
Elements other than those listed above may be analysed on the condition that:
a) suitable reference materials are available; and
b) the instrument is suitably calibrated and equipped.
In the case of determining mercury, for compliance purposes an alternate method with a limit of quantification < 0,000 1 % is recommended as its detection is compromised by intense iron interference at 253,65 nm.
The test result obtained from a spark optical emission spectrometer generally concerns an amount of less than one milligram per spark spot. The result can be used to refer to the laboratory test sample, to the aluminium or aluminium alloy melt or to the cast product.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 515:2017(Main)
Aluminium and aluminium alloys - Wrought products - Temper designations
SIST EN 515:2017

This European Standard establishes temper designations for all forms of wrought aluminium and aluminium alloys and for continuously cast aluminium and aluminium alloys drawing stock and strip intended to be wrought.
NOTE   Some of these temper designations may be subject of patent or patent applications and their listing herein is not to be construed in any way as the granting of a license under such patent right.
Additional temper designations, conforming to this standard, may be standardized with CEN/TC 132 and AECMA/5 provided:
-   the temper is used or is available for use by more than one user;
-   mechanical property limits are defined;
-   the characteristics of the temper are significantly different from those of all other tempers which have the same sequence of basic treatments and for which designations already have been assigned for the same alloy and product;
-   the following are also defined if characteristics other than mechanical properties are considered significant:
a)   test methods and limits for the characteristics; or
b)   the specific practices used to produce the temper.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 755-9:2016(Main)
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
SIST EN 755-9:2016

This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded profile with a cross section contained within a circumscribing circle not greater than 800 mm (see Figure 1).
The temper designations used in this part are according to EN 515.
This European Standard applies to extruded profiles for general engineering applications only.
(...)

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16748:2014(Main)
Aluminium and aluminium alloys - Mechanical potential of Al-Si alloys for high pressure, low pressure and gravity die casting
SIST-TP CEN/TR 16748:2015

This Technical Report presents the characteristics of reference dies and reference castings, to be used for evaluating the mechanical potential (in terms of Ultimate Tensile Strength, Yield Strength and Elongation) which can be expected by Al-Si based alloys, cast by high pressure, low pressure and gravity (permanent mould) processes. These properties are measured on separately cast test specimens produced with state-of-the-art knowledge on die design, process management and alloy treatments correctly applied to minimize defects and imperfections.

  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16749:2014(Main)
Aluminium and aluminium alloys - Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products
SIST-TP CEN/TR 16749:2015

This Technical Report specifies the classification of the defects and imperfections may be present in cast products manufactured by high pressure, low pressure and gravity die casting of aluminium alloys.

  • Technical report
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12258-1:2012(Main)
Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
SIST EN 12258-1:2012

This European Standard defines general terms relating to products of aluminium and aluminium alloys which are helpful for communication within the aluminium industry and with its customers .
It includes terms dealing with aluminium products, processing, sampling and testing, product characteristics and different types of visual quality characteristics.
It does not include terms dealing with bauxite mining, alumina and anode production and aluminium smelting.
This European Standard tries to adhere as closely as possible to the terms and definitions used in other standards or documents.
NOTE   For materials other than aluminium, different definitions can apply to terms which are defined in this document.
This European Standard tries to follow the "common language" as it is used in native English speaking countries, without giving preference to specific idioms of any one of these counties. In cases where in different English-speaking countries different terms are used for the same concept or different concepts refer to an identical term, the appropriate explanations are given.

  • Standard
    180 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 754-4:2008(Main)
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form
SIST EN 754-4:2008

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn square bars having widths across flats from 3 mm up to and including 100 mm.
The temper designations used in this part are according to EN 515.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day