EN 755-9:2016
(Main)Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded profile with a cross section contained within a circumscribing circle not greater than 800 mm (see Figure 1).
The temper designations used in this part are according to EN 515.
This European Standard applies to extruded profiles for general engineering applications only.
(...)
Aluminium und Aluminiumlegierungen - Stranggepresste Stangen, Rohre und Profile - Teil 9: Profile, Grenzabmaße und Formtoleranzen
Diese Europäische Norm legt die Grenzabmaße und Formtoleranzen für stranggepresste Profile aus Aluminium und Aluminiumlegierungen fest, deren Querschnitt in einem Umschlingungskreis mit einem Durchmesser von höchstens 800 mm enthalten ist (siehe Bild 1).
Die in diesem Dokument verwendeten Bezeichnungen der Werkstoffzustände entsprechen EN 515.
Diese Europäische Norm gilt nur für stranggepresste Profile für allgemeine Anwendungen.
Aluminium et alliages d'aluminium - Barres, tubes et profilés filés - Partie 9 : Profilés, tolérances sur dimensions et forme
La présente Norme européenne spécifie les tolérances sur dimensions et forme de profilés filés en aluminium et alliages d’aluminium avec une section transversale contenue dans le cercle circonscrit de 800 mm maximum (voir la Figure 1).
La désignation des états métallurgiques utilisés dans cette partie est conforme à EN 515.
La présente Norme européenne ne s’applique qu’aux profilés filés pour applications générales.
(...)
Aluminij in aluminijeve zlitine - Iztiskane palice/drogovi, cevi in profili - 9. del: Profili, tolerance mer in oblike
Ta evropski standard določa tolerance mer in oblike za iztiskane profile iz aluminija in aluminijeve zlitine s presekom v odprtini, ki ni večji od 800 mm (glej sliko 1).
Oznake za popuščanje, uporabljene v tem delu, so skladne s standardom EN 515.
Ta evropski standard se uporablja samo za iztiskane profile za splošno tehnično uporabo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 755-9:2016
01-september-2016
1DGRPHãþD
SIST EN 755-9:2008
Aluminij in aluminijeve zlitine - Iztiskane palice/drogovi, cevi in profili - 9. del:
Profili, tolerance mer in oblike
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles,
tolerances on dimensions and form
Aluminium und Aluminiumlegierungen - Stranggepresste Stangen, Rohre und Profile -
Teil 9: Profile, Grenzabmaße und Formtoleranzen
Aluminium et alliages d'aluminium - Barres, tubes et profilés filés - Partie 9 : Profilés,
tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: EN 755-9:2016
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 755-9:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 755-9:2016
---------------------- Page: 2 ----------------------
SIST EN 755-9:2016
EN 755-9
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2016
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 755-9:2008
English Version
Aluminium and aluminium alloys - Extruded rod/bar, tube
and profiles - Part 9: Profiles, tolerances on dimensions
and form
Aluminium et alliages d'aluminium - Barres, tubes et Aluminium und Aluminiumlegierungen -
profilés filés - Partie 9 : Profilés, tolérances sur Stranggepresste Stangen, Rohre und Profile - Teil 9:
dimensions et forme Profile, Grenzabmaße und Formtoleranzen
This European Standard was approved by CEN on 11 April 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 755-9:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 755-9:2016
EN 755-9:2016 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Alloy groups . 5
3 Tolerances on dimensions . 6
3.1 Cross-sectional dimensions . 6
3.1.1 General . 6
3.1.2 Tolerances on dimensions other than wall thickness . 6
3.1.3 Tolerances on wall thickness of solid and hollow profiles . 9
3.2 Length . 11
3.3 Squareness of cut ends . 12
4 Tolerances on form . 12
4.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.