Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2010)

ISO 11298-3:2010, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Wasserversorgungsnetzen - Teil 3: Close-Fit-Lining (ISO 11298-3:2010)

Dieser Teil von ISO 11298 legt in Verbindung mit ISO 11298-1 die Anforderungen und Prüfverfahren für Close-Fit-Lining-Systeme fest, die für die Renovierung von Wasserversorgungsnetzen für den Transport von Wasser für den menschlichen Gebrauch einschließlich Rohwasser-Entnahmeleitungen vorgesehen sind.
Er gilt für Rohre aus Polyethylen (PE) sowohl für unabhängige als auch für in Wechselwirkung stehende Druck-Liner-Rohre und die dazugehörigen Formstücke und Verbindungen für den Bau des Lining-Systems.

Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11298-3:2010)

L'ISO 11298-3:2010, conjointement à l'ISO 11298-1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubages par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux enterrés pour l'alimentation en eau, qui acheminent l'eau destinée à la consommation humaine, y compris les canalisations pour prise d'eau brute.
Elle couvre les tubes en polyéthylène (PE) à la fois pour les tubages autostructurants et les tubages nécessitant le maintien de l'enveloppe ainsi que les raccords associés et les assemblages pour la construction du système de rénovation.

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z vodo - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11298-3:2010)

Ta del ISO 11298 v povezavi z ISO 11298-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme oblaganja, ki se uporabljajo za obnovo podzemnih omrežij za oskrbo z vodo, ki prenašajo vodo, namenjeno prehrani ljudi, vključno s cevovodi za vnos neobdelane vode.
Velja za polietilenske (PE) cevi za samostojne in interaktivne obloge za tlačne cevi ter za povezane fitinge in spoje za izdelavo sistema oblaganja.

General Information

Status
Withdrawn
Publication Date
26-Apr-2011
Withdrawal Date
09-Oct-2018
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
10-Oct-2018

Relations

Buy Standard

Standard
EN ISO 11298-3:2011
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2011
1DGRPHãþD
SIST EN 14409-3:2005
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z
vodo - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11298-3:2010)
Plastics piping systems for renovation of underground water supply networks - Part 3:
Lining with close-fit pipes (ISO 11298-3:2010)
Kunststoff-Rohrleitungssysteme für die Renovierung erdverlegter
Wasserversorgungsnetze - Teil 3: Close-Fit-Lining (ISO 11298-3:2010)
Systèmes de canalisations en plastique pour la rénovation de réseaux enterrés
d'alimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO
11298-3:2010)
Ta slovenski standard je istoveten z: EN ISO 11298-3:2011
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
93.025 Zunanji sistemi za prevajanje External water conveyance
vode systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11298-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.20; 23.040.45; 93.025 Supersedes EN 14409-3:2004
English Version
Plastics piping systems for renovation of underground water
supply networks - Part 3: Lining with close-fit pipes (ISO 11298-
3:2010)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux enterrés d'alimentation en eau - Partie 3: erdverlegten Wasserversorgungsnetzen - Teil 3: Close-Fit-
Tubage par tuyau continu sans espace annulaire (ISO Lining (ISO 11298-3:2010)
11298-3:2010)
This European Standard was approved by CEN on 8 April 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11298-3:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 11298-3:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11298-3:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14409-3:2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11298-3:2010 has been approved by CEN as a EN ISO 11298-3:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 11298-3
First edition
2010-03-01
Plastics piping systems for renovation of
underground water supply networks —
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation de réseaux
enterrés d'alimentation en eau —
Partie 3: Tubage par tuyau continu sans espace annulaire

Reference number
ISO 11298-3:2010(E)
©
ISO 2010
ISO 11298-3:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved

ISO 11298-3:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
3.1 General .2
3.2 Techniques.2
3.3 Geometrics.2
3.4 Materials .2
3.5 Product stages.2
3.6 Service conditions.2
3.7 Joints .3
4 Symbols and abbreviated terms .3
4.1 Symbols.3
4.2 Abbreviated terms .4
5 Pipes at the “M” stage .4
5.1 Materials .4
5.2 General characteristics.4
5.3 Material characteristics.4
5.4 Geometric characteristics .5
5.5 Mechanical characteristics.5
5.6 Physical characteristics.5
5.7 Jointing.5
5.8 Marking.5
6 Fittings at the “M” stage.5
7 Ancillary components.6
8 Fitness for purpose of the installed lining system at the “I” stage .6
8.1 Materials .6
8.2 General characteristics.6
8.3 Material characteristics.6
8.4 Geometric characteristics .6
8.5 Mechanical characteristics.7
8.6 Physical characteristics.8
8.7 Additional characteristics.8
8.8 Sampling.8
9 Installation practice.9
9.1 Preparatory work .9
9.2 Storage, handling and transport.9
9.3 Equipment .9
9.4 Installation.10
9.5 Process-related inspection and testing .11
Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe — Determination of
memory ability .12
Bibliography.14

ISO 11298-3:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matter
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.