Fire resistance tests for service installations - Part 9: Single compartment smoke extraction ducts

This part of EN 1366 specifies a test method for determining the fire resistance of smoke extraction ducts that are used for single compartment applications only. In such applications, the smoke extraction system is only intended to function up to flashover (typically 600 °C).
This method of test is only suitable for ducts constructed from non-combustible materials (euro class A1 and A2-s1, d0).
It is applicable only to four sided and circular ducts. One, two and three sided ducts are not covered.
This test has been designed to cover horizontal smoke extraction ducts intended for single compartment applications only.
This test method of part 9 is applicable only to smoke extraction ducts that do not pass through into other fire compartments. It represents fire exposure of a developing fire (pre-flashover). For smoke extraction ducts that pass through into other compartments, the method of test described in EN 1366-8 should be used.
The smoke extraction duct is part of the smoke extraction system which also includes smoke control dampers and smoke extract fans.
The method described in this test standard is complex and requires sophisticated instrumentation. It is not recommended therefore to try to test multiple assemblies in this test.

Feuerwiderstandsprüfungen für Installationen - Teil 9: Entrauchungsleitungen für einen Einzelabschnitt

Dieser Teil von EN 1366 legt ein Prüfverfahren zur Ermittlung der Feuerwiderstandsfähigkeit von Entrauchungsleitungen fest, die nur für die Anwendung in einem Einzelabschnitt eingesetzt werden. Bei solchen Anwendungen ist beabsichtigt, dass die Rauchabzugsanlage nur bis zum Flashover (typischerweise 600 °C) arbeitet.
Dieses Prüfverfahren ist nur für aus nichtbrennbaren Baustoffen (Euroklasse A1 und A2-s1, d0) konstruierte Leitungen geeignet.
Es ist nur für vierseitige und kreisförmige Leitungen geeignet. Ein-, zwei- und dreiseitige Leitungen werden nicht abgedeckt.
Diese Prüfung wurde entwickelt, um horizontale Entrauchungsleitungen abzudecken, die nur für die Anwendung in einem Einzelabschnitt eingesetzt werden.
Dieses Prüfverfahren von Teil 9 gilt nur für Entrauchungsleitungen, die nicht in weitere Brandabschnitte führen. Es stellt die Brandbeanspruchung eines Entstehungsbrandes (Pre-Flashover) dar. Für Entrauchungs¬leitungen, die durch weitere Brandabschnitte hindurchführen, ist das in EN 1366-8 beschriebene Prüfverfahren anzuwenden.
Die Entrauchungsleitung ist Bestandteil der Rauchabzugsanlage, welche ebenfalls Entrauchungsklappen und Rauchabzüge umfasst.
Das in dieser Prüfung beschriebene Verfahren ist komplex und erfordert eine hoch entwickelte Messgeräte¬ausrüstung. Daher wird der Versuch, Parallelanordnungen zu prüfen, nicht empfohlen.

Essai de résistance au feu des installations de service - Partie 9 : Conduits d'extraction de fumées relatifs à un seul compartiment

Preskusi požarne odpornosti servisnih napeljav - 9. del: Kanali za odvod dima iz enega požarnega sektorja

General Information

Status
Published
Publication Date
18-Mar-2008
Withdrawal Date
29-Sep-2008
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
22-Nov-2018

Relations

Buy Standard

Standard
EN 1366-9:2008
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Preskusi požarne odpornosti servisnih napeljav - 9. del: Kanali za odvod dima iz enega požarnega sektorjaFeuerwiderstandsprüfungen für Installationen - Teil 9: Entrauchungsleitungen für einen EinzelabschnittEssai de résistance au feu des installations de service - Partie 9 : Conduits d'extraction de fumées relatifs à un seul compartimentFire resistance tests for service installations - Part 9: Single compartment smoke extraction ducts91.060.40Dimniki, jaški, kanaliChimneys, shafts, ducts13.220.50Požarna odpornost gradbenih materialov in elementovFire-resistance of building materials and elementsICS:Ta slovenski standard je istoveten z:EN 1366-9:2008SIST EN 1366-9:2008en01-maj-2008SIST EN 1366-9:2008SLOVENSKI
STANDARD



SIST EN 1366-9:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1366-9March 2008ICS 13.220.50 English VersionFire resistance tests for service installations - Part 9: Singlecompartment smoke extraction ductsEssai de résistance au feu des installations de service -Partie 9 : Conduits d'extraction de fumées relatifs à un seulcompartimentFeuerwiderstandsprüfungen für Installationen - Teil 9:Entrauchungsleitungen für einen EinzelabschnittThis European Standard was approved by CEN on 21 January 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1366-9:2008: ESIST EN 1366-9:2008



EN 1366-9:2008 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms and definitions.7 4 Test equipment.7 4.1 General.7 4.2 Furnace.7 4.3 Perforated plate.8 4.4 Inlet nozzles (fire test).10 4.5 Ambient leakage measuring device.10 4.6 Pressure sensors for differential pressure control.10 4.7 Welded connecting tube.10 4.8 Extract fan connecting duct.10 4.9 Extraction fan.10 4.10 Thermocouples.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.