EN 1423:1997/A1:2003

Road marking materials - Drop on materials - Glass beads, antiskid aggregates and mixtures of the two

This European Standard specifies the requirements for laboratory tests (Product control) and qualification procedures for the following drop on materials used in road markings. These materials are dropped on to paints, thermoplastics, cold plastics and any other marking product applied in a liquid state, immediately after application to the road surface. The requirements taken into consideration in this standard are: - glass beads: granulometry, refractive index of the glass, chemical resistance, quality, surface treatments; - antiskid aggregates: granulometry, chemical characteristics, friability, colours.

Straßenmarkierungsmaterialien - Nachstreumittel - Markierungs-Glasperlen, Griffigkeitsmittel und Nachstreugemische

Produits de marquage routier - Produits de saupoudrage - Microbilles de verre, granulats antidérapants et mélange de ces deux composants

Materiali za označevanje vozišča – Materiali za posipanje – Steklene kroglice, posipi za zmanjšanje drsnosti in mešanice obeh

General Information

• Status: Withdrawn
• Publication Date: 01-Jul-2003
• Withdrawal Date: 07-Feb-2012
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 226 - Road equipment
• Drafting Committee: CEN/TC 226/WG 2 - Horizontal road signs
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 08-Feb-2012
• Completion Date: 08-Feb-2012
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/111 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on circulation fixtures
• Mandate: M/132 - Addenda to the mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on circulation fixtures, structural bearings and floorings
• Mandate: M/BC/CEN/92/40 - CPD: Circulation fixtures
• Ref Project: SIST EN 1423:1999/A1:2004 - Road marking materials - Drop on materials - Glass beads, antiskid aggregates and mixtures of the two

Relations

• Replaced By: EN 1423:2012 - Road marking materials - Drop on materials - Glass beads, antiskid aggregates and mixtures of the two
• Effective Date: 15-Feb-2012
• Amends: EN 1423:1997 - Road marking materials - Drop on materials - Glass beads, antiskid aggregates and mixtures of the two
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1423:1999/A1:2004
01-januar-2004
0DWHULDOL]DR]QDþHYDQMHYR]LãþD±0DWHULDOL]DSRVLSDQMH±6WHNOHQHNURJOLFH
SRVLSL]D]PDQMãDQMHGUVQRVWLLQPHãDQLFHREHK
Road marking materials - Drop on materials - Glass beads, antiskid aggregates and
mixtures of the two
Straßenmarkierungsmaterialien - Nachstreumittel - Markierungs-Glasperlen,
Griffigkeitsmittel und Nachstreugemische
Produits de marquage routier - Produits de saupoudrage - Microbilles de verre, granulats
antidérapants et mélange de ces deux composants
Ta slovenski standard je istoveten z: EN 1423:1997/A1:2003
ICS:
93.080.20
SIST EN 1423:1999/A1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 1423:1997/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2003
ICS 93.080.20
English version
Road marking materials - Drop on materials - Glass beads,
antiskid aggregates and mixtures of the two
Produits de marquage routier - Produits de saupoudrage - Straßenmarkierungsmaterialien - Nachstreumittel -
Microbilles de verre, granulats antidérapants et mélange de Markierungs-Glasperlen, Griffigkeitsmittel und
ces deux composants Nachstreugemische
This amendment A1 modifies the European Standard EN 1423:1997; it was approved by CEN on 2 May 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1423:1997/A1:2003 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 1423:1997/A1:2003 (E)
Foreword
This document (EN 1423:1997/A1:2003) has been prepared by Technical Committee CEN/TC 226 “Road
equipment”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by January 2004, and conflicting national standards shall be withdrawn at the latest
by April 2005.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This amendment is included in a package with EN 1463-1:1997/prA1 and EN 13212:2001, with a common DOW
fixed on 2003-09-30.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
2

---------------------- Page: 3 ----------------------

EN 1423:1997/A1:2003 (E)
Amendments of Technical nature:
Page 3, add two new sentences to the foreword
•
• Add the following amendments, originally included in document CEN/TC226 N503E and that
correspond to the above mentioned EN 1423:1997/A1 (amendment):
• Page 5/4.1, delete a part of the second paragraph
• Page 6/4.4, complete the first paragraph
• Page 7/4.4, complete the second paragraph and table 4
• Page 8/5.1, modify the maximum value for the pH (9,5 instead of 9,0)
Page 8/5.4, delete a part of the second paragraph
•
• Page 10, delete clause 8 “Marking”
th
• Page 15/Annex B-B.4.1, deletion and substitution of the 4 item
st
• Page 19/Annex C-C.8, deletion and substitution of the 1 paragraph
• Page 29, after Annex G, add a new Annex H (informative)
End of the standard, after (new) Annex H, add Annex ZA (informative)
•
Amendments of Editorial nature:
• Page 4/clause 2 “Normative references”, add the following references mentioned in
amendment A1:
EN 13212:2001 Road marking materials – Requirements for the factory
production control
EN
...