EN 2311:2012
(Main)Aerospace series - Bushes with self-lubricating liner - Technical specification
Aerospace series - Bushes with self-lubricating liner - Technical specification
This European Standard specifies the required characteristics, inspections and tests, quality assurance and qualification, acceptance and delivery conditions for bushes, designed to be subjected under load, to slow sliding movements, rotations and small oscillations only for aerospace applications.
This standard applies to all bushes when referred to in respective product standards or in a design documentation.
The liner is designed to be used in the temperature range of - 50 °C to 163 °C. Aluminium bushes are limited to - 55 °C to 121 °C.
Luft- und Raumfahrt - Buchsen mit selbstschmierender Beschichtung - Technische Lieferbedingungen
Série aérospatiale - Bagues avec garniture autolubrifiante - Spécification technique
Aeronavtika - Puše s samomazalno oblogo - Tehnična specifikacija
Ta evropski standard določa zahtevane značilnosti, preglede in preskuse, zagotavljanje kakovosti in kvalifikacije, pogoje sprejema in dobave za puše, izdelane za prenašanje obremenitev, za počasno drseče premikanje, vrtenje in majhna nihanja za uporabo samo v aeronavtiki. Ta standard se uporablja za vse puše iz posameznih standardov za izdelek ali iz projektne dokumentacije. Obloga je izdelana za uporabo v temperaturnem območju delovanja od –50 do 163 °C. Puše iz aluminija so omejena na razpon od –55 do 121 °C.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Buchsen mit selbstschmierender Beschichtung - Technische LieferbedingungenSérie aérospatiale - Bagues avec garniture autolubrifiante - Spécification techniqueAerospace series - Bushes with self-lubricating liner - Technical specification49.030.99Drugi vezni elementiOther fastenersICS:Ta slovenski standard je istoveten z:EN 2311:2012SIST EN 2311:2012en01-maj-2012SIST EN 2311:2012SLOVENSKI
STANDARDSIST EN 2311:20011DGRPHãþD
SIST EN 2311:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2311
March 2012 ICS 49.030.99 Supersedes EN 2311:1987English Version
Aerospace series - Bushes with self-lubricating liner - Technical specification
Série aérospatiale - Bagues avec garniture autolubrifiante -Spécification technique
Luft- und Raumfahrt - Buchsen mit selbstschmierender Beschichtung - Technische Lieferbedingungen This European Standard was approved by CEN on 23 December 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2311:2012: ESIST EN 2311:2012
EN 2311:2012 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .53.1Description .53.2Loads .53.3Friction torque under load at ambient temperature .63.4Surface discontinuities .63.5Adhesion of the liner .73.6Delivery batch .74Required characteristics, inspection and test methods .85Quality assurance . 115.1Manufacturer's approval . 115.2Product qualification . 116Acceptance conditions . 116.1Manufacturer's responsibility . 116.2Inspections and tests to be carried out by the manufacturer . 116.3Customer quality control .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.