EN 13411-7:2006+A1:2008
(Main)Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
This European Standard specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts.
This European Standard covers those symmetric wedge sockets intended for use at temperatures between
-20 °C and 100 °C.
This European Standard only covers those symmetric wedge sockets that have welded socket bodies.
An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A.
The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A.
This European Standard deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonable foreseeable by the manufacturer.
The hazards covered by this European Standard are identified in Clause 4.
This European Standard applies to symmetric wedge sockets, which are manufactured after the date of its publication.
Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 7: Symmetrische Seilschlösser
Diese Europäische Norm legt die Mindestanforderungen an symmetrische Seilschlösser für Endverbindungen an Aufzugseilen nach EN 12385-5 fest.
Diese Europäische Norm gilt für symmetrische Seilschlösser, die für den Gebrauch bei Temperaturen zwischen 20 °C und 100 °C bestimmt sind.
Diese Europäische Norm gilt nur für symmetrische Seilschlösser mit geschweißtem Gehäuse.
Der informative Anhang A enthält ein Beispiel für die Konstruktion und die Maße eines symmetrischen Seilschlosses.
Der informative Anhang B enthält Empfehlungen für den sicheren Gebrauch und die Prüfung von symme-trischen Seilschlössern nach Anhang A.
Diese Europäische Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und -ereignisse, die für symmetrische Seilschlösser für Endverbindungen für Drahtseile aus Stahldraht relevant sind, wenn diese zweckbestimmend verwendet, und die Bedingungen der Fehlanwendung, die durch den Hersteller angemessen vorhersehbar sind, beachtet werden.
Gefährdungen, die in dieser Norm behandelt werden, sind in Abschnitt 4 angegeben.
Diese Europäische Norm ist für symmetrische Seilschlösser anwendbar, die nach dem Datum ihrer Veröffentlichung hergestellt werden.
Terminaisons pour câbles en acier - Sécurité - Partie 7: Boîte à coin symétrique
La présente Norme européenne spécifie les prescriptions minimales de sécurité des terminaisons de boîte à coin
symétrique destinées aux câbles en acier toronnés pour ascenseurs conformes à l’EN 12385-5.
La présente Norme européenne couvre les boîtes à coin symétrique prévues pour être utilisées à des températures
comprises entre – 20 °C et 100 °C.
La présente Norme européenne traite uniquement des boîtes à coin symétrique dont le corps est soudé.
L’Annexe informative A donne un exemple de construction et de dimensions d’une boîte à coin symétrique.
L’Annexe informative B donne des recommandations permettant l’utilisation et le contrôle en toute sécurité des boîtes
à coin symétrique conformes à l’Annexe A.
La présente Norme européenne traite de tous les phénomènes dangereux et de toutes les situations et événements
dangereux significatifs correspondant aux boîtes à coin symétrique particulières aux terminaisons de câbles en acier,
lorsqu’elles sont utilisées dans les conditions prévues ainsi que dans les conditions de mauvais usage
raisonnablement prévisibles par le fabricant.
Les phénomènes dangereux couverts par la présente Norme européenne sont identifiés à l’Article 4.
La présente Norme européenne s’applique aux boîtes à coin symétrique qui sont fabriquées après la date
de publication.
Zaključki jeklenih žičnih vrvi - Varnost - 7. del: Simetrični zagozdni spoji
General Information
- Status
- Withdrawn
- Publication Date
- 21-Oct-2008
- Withdrawal Date
- 13-Apr-2025
- Technical Committee
- CEN/TC 168 - Chains, ropes, webbing, slings and accessories - safaty
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 07-Jul-2021
- Completion Date
- 14-Apr-2025
- Directive
- 98/37/EC - Machinery
Relations
- Merged From
EN 13411-7:2006 - Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket - Effective Date
- 18-Jan-2023
- Replaced By
EN 13411-7:2021 - Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket - Effective Date
- 05-Jul-2017
Frequently Asked Questions
EN 13411-7:2006+A1:2008 is a standard published by the European Committee for Standardization (CEN). Its full title is "Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket". This standard covers: This European Standard specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts. This European Standard covers those symmetric wedge sockets intended for use at temperatures between -20 °C and 100 °C. This European Standard only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A. The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A. This European Standard deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonable foreseeable by the manufacturer. The hazards covered by this European Standard are identified in Clause 4. This European Standard applies to symmetric wedge sockets, which are manufactured after the date of its publication.
This European Standard specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts. This European Standard covers those symmetric wedge sockets intended for use at temperatures between -20 °C and 100 °C. This European Standard only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A. The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A. This European Standard deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonable foreseeable by the manufacturer. The hazards covered by this European Standard are identified in Clause 4. This European Standard applies to symmetric wedge sockets, which are manufactured after the date of its publication.
EN 13411-7:2006+A1:2008 is classified under the following ICS (International Classification for Standards) categories: 21.060.70 - Clamps and staples; 53.020.30 - Accessories for lifting equipment. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 13411-7:2006+A1:2008 has the following relationships with other standards: It is inter standard links to EN 13411-7:2006, EN 13411-7:2021. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 13411-7:2006+A1:2008 is associated with the following European legislation: EU Directives/Regulations: 2006/42/EC, 2014/33/EU, 95/16/EC, 98/37/EC; Standardization Mandates: M/079, M/396, M/BC/CEN/92/3. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN 13411-7:2006+A1:2008 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 7: Symmetrische SeilschlösserTerminaisons pour câbles en acier - Sécurité - Partie 7: Boîte à coin symétriqueTerminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket77.140.99Drugi železni in jekleni izdelkiOther iron and steel products53.020.30Pribor za dvigalno opremoAccessories for lifting equipmentICS:Ta slovenski standard je istoveten z:EN 13411-7:2006+A1:2008SIST EN 13411-7:2006+A1:2008en,fr01-december-2008SIST EN 13411-7:2006+A1:2008SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13411-7:2006+A1
October 2008 ICS 21.060.70; 53.020.30 Supersedes EN 13411-7:2006 English Version
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
Terminaisons pour câbles en acier - Sécurité - Partie 7: Boîte à coin symétrique
Endverbindungen für Drahtseile aus Stahldraht -Sicherheit - Teil 7: Symmetrische Seilschlösser This European Standard was approved by CEN on 10 May 2006 and includes Amendment 1 approved by CEN on 18 September 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13411-7:2006+A1:2008: ESIST EN 13411-7:2006+A1:2008
Construction and sizes for one design of symmetric wedge socket with welded socket body.13 Annex B (informative)
Recommendations for safe use and inspection of symmetric wedge sockets conforming to Annex A, to be provided by the manufacturer.16 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 95/16/EC.18 Annex ZB (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC.19 Annex ZC (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""".20 Bibliography.21
-20 °C and 100 °C. This European Standard only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A. The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A. This European Standard deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonable foreseeable by the manufacturer. The hazards covered by this European Standard are identified in Clause 4. This European Standard applies to symmetric wedge sockets, which are manufactured after the date of its publication. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1050:1996, Safety of machinery — Principles for risk assessment EN 1289:1998, Non-destructive testing of welds — Penetrant testing of welds — Acceptance levels EN 1290:1998, Non-destructive examination of welds — Magnetic particle examination of welds EN 10045-1, Metallic materials — Charpy impact test — Part 1: Test method EN 12385-2:2002, Steel wire ropes — Safety — Part 2: Definitions, designation and classification EN 12385-5:2002, Steel wire ropes — Safety — Part 5: Stranded ropes for lifts EN ISO 4063, Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:1998) EN ISO 5817,
Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections (ISO 5817:2003) EN ISO 7500-1:2004, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system
(ISO 7500-1:2004) ) EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1:
Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles (ISO 12100-2:2003) SIST EN 13411-7:2006+A1:2008
EN ISO 12100-2:2003, EN 12385-2:2002 and the following apply. 3.1 symmetric wedge socket assembly consisting of a socket body, wedge, and pin and securing means for the pin; when assembled the centre line of the pin is marginally offset (by one half rope diameter, see Figure B.1) to the longitudinal axis of the live portion of the rope
3.2 socket body principal component of a wedge socket termination having an internal tapered form suitable for receiving a wedge (see 3.3) and the rope with which the wedge is associated, see Figure A.1 3.3 wedge flat tapered component with peripheral groove, suitable for fitting into a tapered socket body to accommodate a rope of matching nominal diameter, see Figure A.1 3.4 pin removable component intended to facilitate connection of the socket body to its anchorage point 3.5 lot number of symmetric wedge sockets from which samples are selected for testing purposes which are of the same type and dimension, each of their constituent components manufactured during the same production run from material of the same cast and subjected to the same heat treatment process 4 List of significant hazards This European Standard contains all the significant hazards, hazardous situations and events, as far as they are dealt with in this European Standard, identified by risk assessment as significant for this type of steel wire rope termination that require action to eliminate or reduce the risk. In particular, the hazard caused by accidental release of a load, or release of a load due to failure of a symmetric wedge socket, puts at risk, either directly or indirectly, the safety or health of those persons within the hazard zone. Errors in the fitting of accessories can also lead to premature failure and this European Standard contains dimensional and geometrical requirements to allow correct fit. Table 1 contains those hazards that require action to reduce risk identified by risk assessment as being specific and significant for symmetric wedge sockets. SIST EN 13411-7:2006+A1:2008
Mechanical hazard due to inadequacy of strength 6
7 1.3 Cutting or shearing hazard 7 15 Errors of fitting 7
5 Safety requirements and/or measures 5.1 Geometry of wedge and socket body Symmetric wedge socket terminations for ropes shall conform to the following geometrical criteria
(see Figure A.1): • the wedge groove angle (.) shall be the same as the socket angle in the body (); • the wedge shall be symmetric; • the internal side surfaces of the socket body and the wedge in contact with the rope shall be straight; • the grooves of the body and the wedge shall have no surface irregularities, such as, protrusions or joints which could influence the intimate contact with the rope; • the clamping length between the socket body and the wedge shall be at least 7,3 times the nominal rope diameter d; • the radius r3 of the wedge at the bottom of the groove at the large end shall be at least 1 times the nominal diameter d of the rope. 5.2 Security of the pin The pin shall be provided with a means for securing it in position when in operation. 5.3 Welded socket body The welding and allied process shall conform to one of those specified in EN ISO 4063. The person who supervises the production process shall be trained in the chosen welding process. The quality of the welding joint shall be in accordance with assessment group B of EN ISO 5817:2003. There shall be no melted on weld chips. The ligament distance in the root of the welding joint shall be 1 mm for material thickness up to 6 mm and
1,5 mm for material thickness more than 6 mm up to and including 12 mm. The penetration of the root of the welding shall be avoided. There shall be no increase of the welding joint in the area of contact with the rope. The welding joint shall have a bonding area of at least 70 % at the joint edge. SIST EN 13411-7:2006+A1:2008
...
EN 13411-7:2006+A1:2008 is a European standard that sets the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes in lifts. It covers sockets intended for use between -20°C and 100°C and those with welded socket bodies. The standard includes an example of construction and sizes in Annex A, as well as recommendations for safe use and inspection in Annex B. It addresses all significant hazards and hazardous situations related to these sockets when used properly or in foreseeable misuse conditions. The standard applies to sockets manufactured after its publication.
記事タイトル：EN 13411-7:2006+A1:2008 - 鋼線ロープの終端 - 安全 - 第7部：対称ウェッジソケット 記事内容：この欧州規格は、リフト用のEN 12385-5に適合する座状ウェッジソケット終端の最低要件を規定しています。この欧州規格は、-20℃から100℃の温度で使用される対称ウェッジソケットに対象を限定しています。この欧州規格は、接合部の溶接が施された対称ウェッジソケットのみを対象とします。対称ウェッジソケットの構造やサイズの例は付属の参考付録Aに記載されています。情報付録Bでは、参考付録Aに基づく対称ウェッジソケットの安全使用と点検に関する推奨事項が提示されています。この欧州規格は、製造業者が合理的に予測可能な誤用条件の下で正しく使用された場合、およびその他の予測可能な誤用条件下の鋼線ロープの終端での、すべての重要な危険、危険状況、およびイベントを扱います。この欧州規格でカバーされる危険要素は第4条で示されています。この欧州規格は、その発行後に製造された対称ウェッジソケットに適用されます。
기사 제목: EN 13411-7:2006+A1:2008 - 강철 와이어로프용 종단 부착물 - 안전 - 제7부: 대칭 웨지 소켓 기사 내용: 이 유럽 표준은 EN 12385-5에 준하는 구조 강선 와이어로프용 대칭 웨지 소켓 종단 부착물에 대한 최소 요구사항을 명시합니다. 이 유럽 표준은 -20°C에서 100°C 사이의 온도에서 사용되는 대칭 웨지 소켓을 다룹니다. 이 유럽 표준은 용접된 소켓 본체를 가진 대칭 웨지 소켓만 해당합니다. 대칭 웨지 소켓의 구조 및 크기 예시는 영감을 주는 부록 A에 나와 있습니다. 정보 부록 B에는 부록 A에 따른 대칭 웨지 소켓의 안전 사용 및 조사에 대한 권고사항이 제공됩니다. 이 유럽 표준은 제조업자가 합리적으로 예측 가능한 오용 조건을 가정하고 용접된 소켓 와이어로프 종단 부착물에 적용되는 모든 주요 위험, 위험상황 및 사건을 다룹니다. 이 유럽 표준이 다루는 위험 요소는 4조에서 확인할 수 있습니다. 이 유럽 표준은 해당 출판일 이후에 제조된 대칭 웨지 소켓에 적용됩니다.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...