EN 13674-3:2006+A1:2010
(Main)Railway applications - Track - Rail - Part 3: Check rails
Railway applications - Track - Rail - Part 3: Check rails
This European Standard specifies check rail profiles which have been designed for this purpose. It does not cover guard rails which are to protect vehicle, bridge, viaduct and other structures in the event of a derailment.
Three grades of steel and five rail profiles are specified.
Bahnanwendungen - Oberbau - Schienen - Teil 3: Radlenkerschienen
Diese Dokument legt Schienenprofile fest, die speziell für die Anwendung als Radlenker konstruiert wurden, und gilt nicht für Führungsschienen, die dafür bestimmt sind, bei Entgleisungen das Fahrzeug selbst sowie Brücken und andere Bauten zu schützen.
Drei Stahlsorten und fünf Schienenprofile sind festgelegt.
Applications ferroviaires - Voie - Rails - Partie 3: Contre-rails
La présente partie de la Norme européenne spécifie les profils de contre-rails. Elle ne concerne pas les rails de sécurité dont le rôle est de protéger les véhicules, les ponts, les viaducs et autres structures dans le cas d'un déraillement.
Trois nuances d'acier et cinq profils de rails sont spécifiés.
Železniške naprave - Zgornji ustroj - Tirnice - 3. del: Vodilne tirnice
Ta evropski standard določa profile vodilnih tirnic, ki so bile zasnovane v ta namen. Ne zajema varnostnih tirnic, ki ščitijo vozilo, mostove, viadukte in druge strukture v primeru iztirjenja. Določene so tri vrste jekla in pet profilov tirnic.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Železniške naprave - Zgornji ustroj - Tirnice - 3. del: Vodilne tirniceBahnanwendungen - Oberbau - Schienen - Teil 3: RadlenkerschienenApplications ferroviaires - Voie - Rails - Partie 3: Contre-railsRailway applications - Track - Rail - Part 3: Check rails45.080Rails and railway componentsICS:Ta slovenski standard je istoveten z:EN 13674-3:2006+A1:2010SIST EN 13674-3:2006+A1:2010en,fr,de01-september-2010SIST EN 13674-3:2006+A1:2010SLOVENSKI
STANDARD
SIST EN 13674-3:2006+A1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13674-3:2006+A1
July 2010 ICS 93.100 Supersedes EN 13674-3:2006English Version
Railway applications - Track - Rail - Part 3: Check rails
Applications ferroviaires - Voie - Rails - Partie 3: Contre-rails
Bahnanwendungen - Oberbau - Schienen - Teil 3: Radlenkerschienen This European Standard was approved by CEN on 13 February 2006 and includes Amendment 1 approved by CEN on 15 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13674-3:2006+A1:2010: ESIST EN 13674-3:2006+A1:2010
EN 13674-3:2006+A1:2010 (E) 2 Contents Page Foreword .31Scope .52Normative references .53Terms and definitions .54Information to be supplied by the purchaser .55Steel grades .56Profile drawings/properties/mass .67Manufacture .67.1Product integrity .67.2Identification .68Acceptance tests .78.1Chemical composition .78.2Hydrogen .78.3Hardness .78.4Profile tolerances .88.5Straightness and twist .88.6Cutting .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.