EN 13480-8:2012/A2:2015
(Amendment)Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping
Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping
This Part of this European Standard specifies requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480:2012 and CEN/TR 13480-7:2002. Revision of Annex B "Transition joints".
Metallische industrielle Rohrleitungen - Teil 8: Zusatzanforderungen an Rohrleitungen aus Aluminium und Aluminumlegierungen
Tuyauteries industrielles métalliques - Partie 8 : Exigences complémentaires relatives aux tuyauteries en aluminium et alliages d'aluminium
Kovinski industrijski cevovodi - 8. del: Dodatne zahteve za cevovode iz aluminija in aluminijevih zlitin
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13480-8:2012/oprA2:2015
01-maj-2015
Kovinski industrijski cevovodi - 8. del: Dodatne zahteve za cevovode iz aluminija
in aluminijevih zlitin
Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium
alloy piping
Metallische industrielle Rohrleitungen - Teil 8: Zusatzanforderungen an Rohrleitungen
aus Aluminium und Aluminumlegierungen
Tuyauteries industrielles métalliques - Partie 8: Exigences complémentaires relatives aux
tuyauteries en aluminium et alliages d'aluminium
Ta slovenski standard je istoveten z: EN 13480-8:2012/prA2
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 13480-8:2012/oprA2:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 13480-8:2012/oprA2:2015
SIST EN 13480-8:2012/oprA2:2015
EUROPEAN STANDARD
DRAFT
EN 13480-8:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
February 2015
ICS 23.040.15
English Version
Metallic industrial piping - Part 8: Additional requirements for
aluminium and aluminium alloy piping
Tuyauteries industrielles métalliques - Partie 8: Exigences Metallische industrielle Rohrleitungen - Teil 8:
complémentaires relatives aux tuyauteries en aluminium et Zusatzanforderungen an Rohrleitungen aus Aluminium und
alliages d'aluminium Aluminumlegierungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 267.
This draft amendment A2, if approved, will modify the European Standard EN 13480-8:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-8:2012/prA2:2015 E
worldwide for CEN national Members.
SIST EN 13480-8:2012/oprA2:2015
EN 13480-8:2012/prA2:2015 (E)
Contents Page
Foreword .3
1 Modification to Clause 2 .4
2 Modification to 5.1 .6
3 Modification to 5.2 .6
4 Modification to 5.3 .6
5 Modification to 5.6 .6
6 Modification to Table 7.5-1 .7
7 Modification to Table 8.5-1 .7
8 Modification of Table 8.6-2 .8
9 Modification to B.5.1.1 .9
10 Modification to Table B.1 .9
SIST EN 13480-8:2012/oprA2:2015
EN 13480-8:2012/prA2:2015 (E)
Foreword
This document (EN 13480-8:2012/prA2:2015) has been prepared by Technical Committee CEN/TC 267
“Metallic industrial piping”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This document includes the text of the amendment itself. The amended/corrected pages of EN 13480-8:2012
will be published as Issue 4 of the European Standard.
SIST EN 13480-8:2012/oprA2:2015
EN 13480-8:2012/prA2:2015 (E)
1 Modification to Clause 2
Replace the list of normative references by the following:
EN 485-2:2013, Aluminium and aluminium alloys — Sheet, strip and plate — Part 2: Mechanical properties
EN 485-3, Aluminium and aluminium alloys — Sheet, strip and plate — Part 3: Tolerances on dimensions and
form for hot-rolled products
EN 485-4, Aluminium and aluminium alloys — Sheet, strip and plate — Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 573-3:2013, Aluminium and aluminium alloys — Chemical composition and form of wrought products —
Part 3: Chemical composition and form of products
EN 586-2:1994, Aluminium and aluminium alloys — Forgings — Part 2: Mechanical properties and additional
property requirements
EN 754 (all parts), Aluminium and aluminium alloys — Cold drawn rod/bar and tube
EN 755 (all parts), Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles
EN 764-3, Pressure equipment — Part 3: Definition of parties involved
EN 1779:1999, Non-destructive testing — Leak testing — Criteria for method and technique selection
EN 10204:2004, Metallic products — Types of inspection documents
EN 12392:2000, Aluminium and aluminium alloys — Wrought products — Special requirements for products
intended for the production of pressure equipment
EN 13445-4:2014, Unfired pressure vessels — Part 4: Fabrication
EN 13480-1:2012, Metallic industrial piping — Part 1: General
EN 13480-2:2012, Metallic industrial piping — Part 2: Materials
EN 13480-3:2012, Metallic industrial piping — Part 3: Design and calculation
EN 13480-4:2012, Metallic industrial piping — Part 4: Fabrication and installation
EN 13480-5:2012, Metallic industrial piping — Part 5: Inspection and testing
EN ISO 148-1:2010, Metallic materials — Charpy pendulum impact test — Part 1: Test method
(ISO 148-1:2009)
EN ISO 3452-1:2013, Non-destructive testing — Penetrant testing — Part 1: General principles
(ISO 3452-1:2013)
EN ISO 3834-2:2005, Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive
quality requirements (ISO 3834-2:2005)
EN ISO 3834-3:2005, Quality requirements for fusion welding of metallic materials — Part 3: Standard quality
requirements (ISO 3834-3:2005)
EN ISO 4063:2010, Welding and allied processes — Nomenclature of processes and reference numbers
(ISO 4063:2009, Corrected version 2010-03-01)
EN ISO 4136:2012, Destructive tests on welds in metallic materials — Transverse tensile test
(ISO 4136:2012)
EN ISO 5173:2010 + A1:2011, Destructive tests on welds in metallic materials — Bend tests (ISO 5173:2009
+ Amd 1:2011)
SIST EN 13480-8:2012/oprA2:2015
EN 13480-8:2012/prA2:2015 (E)
EN ISO 6892-1:2009, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
(ISO 6892 1:2009)
EN ISO 6892-2:2011, Metallic materials — Tensile testing — Part 2: Method of test at elevated temperature
(ISO 6892 2:2011)
EN ISO 7438:2005, Metallic materials — Bend test (ISO 7438:2005)
EN ISO 9606-2:2004, Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium
alloys (ISO 9606-2:2004)
EN ISO 10042:2005, Welding — Arc-welded joints in aluminium and its alloys — Quality levels for
imperfections (ISO 10042:2005)
EN ISO 10893-8:2011, Non-destructive testing of steel tubes — Part 8: Automated ultrasonic testing of
seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011)
EN ISO 10893-11:2011, Non-destructive testing of steel tubes — Part 11: Automated ultrasonic testing of the
weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections
(ISO 10893-11:2011)
EN ISO 11666:2010, Non-destructive testing of welds — Ultrasonic testing — Acceptance levels
(ISO 11666:2010)
EN ISO 15614-2:2005, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
EN ISO 16810:2014, Non-destructive testing — Ultrasonic testing — General principles (ISO 16810:2012)
EN ISO 16811:2014, Non-destructive testing — Ultrasonic testing — Sensitivity and range setting
(ISO 16811:2012)
EN ISO 16823:2014, Non-destructive testing — Ultrasonic testing — Transmission technique
(ISO 16823:2012)
EN ISO 16826:2014, Non-destructive testing — Ultrasonic testing — Examination for discontinuities
perpendicular to the surface (ISO 16826:2012)
EN ISO 16827:2014, Non-destructive testing — Ultrasonic testing — Characterization and sizing of
discontinuities (ISO 16827:2012)
EN ISO 16828:2014, Non-destructive testing — Ultrasonic testing — Time-of-flight diffraction technique as a
method for detection and sizing of discontinuities (ISO 16828:2012)
EN ISO 17636-1:2013, Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray
techniques with film (ISO 17636-1:2013)
EN ISO 17636-2:2013, Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray
techniques with digital detectors (ISO 17636-2:2013)
EN ISO 17637:2011, Non-destructive testing of welds — Visual testing of fusion-welded joints
(ISO 17637:2003)
EN ISO 17639:2013, Destructive tests on welds in metallic materials — Macroscopic and microscopic
examination of welds (ISO 17639:2003)
EN ISO 17640:2010, Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels, and
assessment (ISO 17640:2010)
EN ISO 23277:2009, Non-destructive testing of welds — Penetrant testing of welds — Acceptance levels
(ISO 23277:2006)
CEN ISO/TR 15608:2013, Welding — Guidelines for a metallic materials grouping system
(ISO/TR 15608:2013)
SIST EN 13480-8:2012/oprA2:2015
EN 13480-8:2012/prA2:2015 (E)
ISO 857-1:1998, Welding and allied processes — Vocabulary — Part 1: Metal welding processes
2 Modification to 5.1
Replace sub-clause 5.1 by the following:
5.1 General
Materials for pressure-bearing parts compliant with the requirements of this European Standard shall be
accompanied by inspection documents in accordance with EN 10204:2004.
The type of inspection document shall be in accordance with EN 764-5:2002 and include a declaration of
compliance to the material specification.
The requirements of EN 13480-2:2012 shall apply with the following additions/exclusions:
3 Modification to 5.2
Replace table title of Table 5.2-1 by the following:
Table 5.2-1 — Grouping system based on CEN ISO/TR 15608:2013 and EN AW numbers according to
EN 573-3:2013
4 Modification to 5.3
Replace sub-clause 5.3 by the following:
5.3 Elongation after fracture
Aluminium and aluminium alloys used for parts of industrial piping that are subjected to cold forming shall
have a specified minimum elongation after fracture measured on a gauge length
L = 5,65 S (5.3-1)
o o
that is ≥ 14 % in the longitudinal or transverse direction as defined by the material specification.
Aluminium and aluminium alloys used for parts of industrial piping that are not subjected to cold forming (e.g.
straight flanges and nozzles) shall have a specified minimum elongation after fracture of ≥ 10 % in the
longitudinal or transverse direction as defined by the material specification measured on a gauge length as
defined in equation (5.3-1).
5 Modification to 5.6
Replace sub-clause 5.6 by the following:
NOTE 1 See also EN 13480-2:2012, 4.2.2.
nd
EN 13480-2:2012, 4.2.2.1, 2 paragraph is not applicable for aluminium and aluminium alloys.
Nominal design stress values are given in Table C.1, Table C.2, Table C.3 and Table C.4. Design
temperatures that exceed the respective temperature limit in Annex C are not permitted.
For materials of group 22.4 temperatures above 80 °C may result in grain boundary precipitation of Al -Mg .
3 2
These materials may be used at temperatures above 80 °C up to 200 °C only for non-corrosive service.
NOTE 2 For further material properties, see EN 12392:2000.
SIST EN 13480-8:2012/oprA2:2015
EN 13480-8:2012/prA2:2015 (E)
For welded parts and heat treated parts after forming only the values equivalent to the O temper shall be used
for design when 6 000 series flanges, etc. are welded. Nominal design stresses are given in C.6. The weld
area shall be based on the O temper but the flange strength away from the weld (2t) may be based on the
actual temper (T4 or T6).
For aluminium and aluminium alloys values of 0,2 % proof strength (or 1 % proof strength for material group
21-1 000 series aluminium) for temperatures above 20 °C shall be established by lin
...
SLOVENSKI STANDARD
01-november-2015
Kovinski industrijski cevovodi - 8. del: Dodatne zahteve za cevovode iz aluminija
in aluminijevih zlitin
Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium
alloy piping
Metallische industrielle Rohrleitungen - Teil 8: Zusatzanforderungen an Rohrleitungen
aus Aluminium und Aluminumlegierungen
Tuyauteries industrielles métalliques - Partie 8: Exigences complémentaires relatives aux
tuyauteries en aluminium et alliages d'aluminium
Ta slovenski standard je istoveten z: EN 13480-8:2012/A2:2015
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13480-8:2012/A2
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2015
EUROPÄISCHE NORM
ICS 23.040.15
English Version
Metallic industrial piping - Part 8: Additional requirements
for aluminium and aluminium alloy piping
Tuyauteries industrielles métalliques - Partie 8 : Metallische industrielle Rohrleitungen - Teil 8:
Exigences complémentaires relatives aux tuyauteries Zusatzanforderungen an Rohrleitungen aus Aluminium
en aluminium et alliages d'aluminium und Aluminumlegierungen
This amendment A2 modifies the European Standard EN 13480-8:2012; it was approved by CEN on 2 September 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-8:2012/A2:2015 E
worldwide for CEN national Members.
Contents Page
European foreword.3
1 Modification to Clause 2 .4
2 Modification to 5.1 .6
3 Modification to 5.2 .6
4 Modification to 5.3 .6
5 Modification to 5.6 .7
6 Modification to Table 7.5-1 .7
7 Modification to Table 8.5-1 .7
8 Modification of Table 8.6-2 .8
9 Modification to B.5.1.1 .9
10 Modification to Table B.1 .9
European foreword
This document (EN 13480-8:2012/A2:2015) has been prepared by Technical Committee CEN/TC 267
“Metallic industrial piping”, the secretariat of which is held by AFNOR.
This amendment to EN 13480-8:2012 shall be given the status of a national standard, either by
publication of an identical text or by endorsement, at the latest by March 2016, and conflicting national
standards shall be withdrawn at the latest by March 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of EN 13480-
8:2012.
This document includes the text of the amendment itself. The corrected pages of EN 13480-8:2012 will
be published as Issue 5 of the European Standard.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
1 Modification to Clause 2
Replace the list of normative references by the following:
EN 485-2:2013, Aluminium and aluminium alloys — Sheet, strip and plate — Part 2: Mechanical
properties
EN 485-3, Aluminium and aluminium alloys — Sheet, strip and plate — Part 3: Tolerances on dimensions
and form for hot-rolled products
EN 485-4, Aluminium and aluminium alloys — Sheet, strip and plate — Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 573-3:2013, Aluminium and aluminium alloys — Chemical composition and form of wrought products
— Part 3: Chemical composition and form of products
EN 586-2:1994, Aluminium and aluminium alloys — Forgings — Part 2: Mechanical properties and
additional property requirements
EN 754 (all parts), Aluminium and aluminium alloys — Cold drawn rod/bar and tube
EN 755 (all parts), Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles
EN 764-3, Pressure equipment — Part 3: Definition of parties involved
EN 1779:1999, Non-destructive testing — Leak testing — Criteria for method and technique selection
EN 10204:2004, Metallic products — Types of inspection documents
EN 12392:2000, Aluminium and aluminium alloys — Wrought products — Special requirements for
products intended for the production of pressure equipment
EN 13445-4:2014, Unfired pressure vessels — Part 4: Fabrication
EN 13480-1:2012, Metallic industrial piping — Part 1: General
EN 13480-2:2012, Metallic industrial piping — Part 2: Materials
EN 13480-3:2012, Metallic industrial piping — Part 3: Design and calculation
EN 13480-4:2012, Metallic industrial piping — Part 4: Fabrication and installation
EN 13480-5:2012, Metallic industrial piping — Part 5: Inspection and testing
EN ISO 148-1:2010, Metallic materials — Charpy pendulum impact test — Part 1: Test method
(ISO 148-1:2009)
EN ISO 3452-1:2013, Non-destructive testing — Penetrant testing — Part 1: General principles
(ISO 3452-1:2013)
EN ISO 3834-2:2005, Quality requirements for fusion welding of metallic materials — Part 2:
Comprehensive quality requirements (ISO 3834-2:2005)
EN ISO 3834-3:2005, Quality requirements for fusion welding of metallic materials — Part 3: Standard
quality requirements (ISO 3834-3:2005)
EN ISO 4063:2010, Welding and allied processes — Nomenclature of processes and reference numbers
(ISO 4063:2009, Corrected version 2010-03-01)
EN ISO 4136:2012, Destructive tests on welds in metallic materials — Transverse tensile test
(ISO 4136:2012)
EN ISO 5173:2010 + A1:2011, Destructive tests on welds in metallic materials — Bend tests (ISO
5173:2009 + Amd 1:2011)
EN ISO 6892-1:2009, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
(ISO 6892-1:2009)
EN ISO 6892-2:2011, Metallic materials — Tensile testing — Part 2: Method of test at elevated
temperature (ISO 6892-2:2011)
EN ISO 7438:2005, Metallic materials — Bend test (ISO 7438:2005)
EN ISO 9606-2:2004, Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium
alloys (ISO 9606-2:2004)
EN ISO 10042:2005, Welding — Arc-welded joints in aluminium and its alloys — Quality levels for
imperfections (ISO 10042:2005)
EN ISO 10893-8:2011, Non-destructive testing of steel tubes — Part 8: Automated ultrasonic testing of
seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011)
EN ISO 10893-11:2011, Non-destructive testing of steel tubes — Part 11: Automated ultrasonic testing of
the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections
(ISO 10893-11:2011)
EN ISO 11666:2010, Non-destructive testing of welds — Ultrasonic testing — Acceptance levels
(ISO 11666:2010)
EN ISO 15614-2:2005, Specification and qualification of welding procedures for metallic materials —
Welding procedure test — Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
EN ISO 16810:2014, Non-destructive testing — Ultrasonic testing — General principles (ISO 16810:2012)
EN ISO 16811:2014, Non-destructive testing — Ultrasonic testing — Sensitivity and range setting
(ISO 16811:2012)
EN ISO 16823:2014, Non-destructive testing — Ultrasonic testing — Transmission technique
(ISO 16823:2012)
EN ISO 16826:2014, Non-destructive testing — Ultrasonic testing — Examination for discontinuities
perpendicular to the surface (ISO 16826:2012)
EN ISO 16827:2014, Non-destructive testing — Ultrasonic testing — Characterization and sizing of
discontinuities (ISO 16827:2012)
EN ISO 16828:2014, Non-destructive testing — Ultrasonic testing — Time-of-flight diffraction technique
as a method for detection and sizing of discontinuities (ISO 16828:2012)
EN ISO 17636-1:2013, Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-
ray techniques with film (ISO 17636-1:2013)
EN ISO 17636-2:2013, Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-
ray techniques with digital detectors (ISO 17636-2:2013)
EN ISO 17637:2011, Non-destructive testing of welds — Visual testing of fusion-welded joints
(ISO 17637:2003)
EN ISO 17639:2013, Destructive tests on welds in metallic materials — Macroscopic and microscopic
examination of welds (ISO 17639:2003)
EN ISO 17640:2010, Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels,
and assessment (ISO 17640:2010)
EN ISO 23277:2009, Non-destructive testing of welds — Penetrant testing of welds — Acceptance levels
(ISO 23277:2006)
CEN ISO/TR 15608:2013, Welding — Guidelines for a metallic materials grouping system
(ISO/TR 15608:2013)
ISO 857-1:1998, Welding and allied processes — Vocabulary — Part 1: Metal welding processes
2 Modification to 5.1
Replace sub-clause 5.1 by the following:
5.1 General
Materials for pressure-bearing parts compliant with the requirements of this European Standard shall
be accompanied by inspection documents in accordance with EN 10204:2004.
The type of inspection document shall be in accordance with EN 764-5:2002 and include a declaration
of compliance to the material specification.
The requirements of EN 13480-2:2012 shall apply with the following additions/exclusions:
3 Modification to 5.2
Replace table title of Table 5.2-1 by the following:
Table 5.2-1 — Grouping system based on CEN ISO/TR 15608:2013 and EN AW numbers
according to EN 573-3:2013
4 Modification to 5.3
Replace sub-clause 5.3 by the following:
5.3 Elongation after fracture
Aluminium and aluminium alloys used for parts of industrial piping that are subjected to cold forming
shall have a specified minimum elongation after fracture measured on a gauge length
L = 5,65 S (5.3-1)
o o
that is ≥ 14 % in the longitudinal or transverse direction as defined by the material specification.
Aluminium and aluminium alloys used for parts of industrial piping that are not subjected to cold
forming (e.g. straight flanges and nozzles) shall have a specified minimum elongation after fracture of
≥ 10 % in the longitudinal or transverse direction as defined by the material specification measured on
a gauge length as defined in equation (5.3-1).
5 Modification to 5.6
Replace sub-clause 5.6 by the following:
NOTE 1 See also EN 13480-2:2012, 4.2.2.
nd
EN 13480-2:2012, 4.2.2.1, 2 paragraph is not applicable for aluminium and aluminium alloys.
Nominal design stress values are given in Table C.1, Table C.2, Table C.3 and Table C.4. Design
temperatures that exceed the respective temperature limit in Annex C are not permitted.
For materials of group 22.4 temperatures above 80 °C may result in grain boundary precipitation of Al -
Mg . These materials may be used at temperatures above 80 °C up to 200 °C only for non-corrosive
service.
NOTE 2 For further material properties, see EN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.