EN ISO 1401:1999

Rubber hoses for agricultural spraying (ISO 1401:1999)

Migrated from Progress Sheet (TC Comment) (2000-07-10): Refered to CEN/TC 218 after PQ ++ TC 62 Resolution 62 a) (meeting 19960515): ISO 1401:1987 is in course of ++ revision, it is expected to be an ISO/DIS in 1996; shall be dual voted ++ with the lead in ISO (ISO/TC 45/SC1/WG1) ++ letter of TC Secr. to Mr. F. Reuter dated 970213: ISO/TC45/SC1 may opt for the ++ DIS to be issued as a single language version as France is now 0 members. If ++ it is so, it undermines the objectives of trying to progress ISO & CEN together. ++ TA/970219.

Gummischläuche zum Sprühen in der Landwirtschaft (ISO 1401:1999)

Diese Internationale Norm legt die Anforderungen fest für drei Typen von Gummischläuchen für das Versprühen agropharmazeutischer und/oder Düngemittelprodukte in einem Temperaturbereich von -10°C bis +60°C.

Tuyaux en caoutchouc pour pulvérisation agricole (ISO 1401: 1999)

La présente Norme internationale spécifie les exigences de trois types de tuyaux en caoutchouc flexible pour pulvérisation à pression de produits agropharmaceutiques et/ou de produits fertilisants à une température comprise entre - 10 °C et + 60 °C.

Gumene cevi za škropljenje v poljedelstvu (ISO 1401:1999)

General Information

• Status: Withdrawn
• Publication Date: 30-Nov-1999
• Withdrawal Date: 29-Jun-2000
• ICS: 83.060 - Rubber
• ICS: 83.140 - Rubber and plastics products
• Technical Committee: CEN/TC 218 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: CEN/TC 218/WG 1 - Rubber and plastics hoses and hose assemblies for industrial, chemical and petrochemical applications
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 30-Nov-2016
• Ref Project: SIST EN ISO 1401:2000 - Rubber hoses for agricultural spraying (ISO 1401:1999)

Relations

• Replaced By: EN ISO 1401:2016 - Rubber hoses for agricultural spraying (ISO 1401:2016)
• Effective Date: 10-Dec-2014

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2000
Gumene cevi za škropljenje v poljedelstvu (ISO 1401:1999)
Rubber hoses for agricultural spraying (ISO 1401:1999)
Gummischläuche zum Sprühen in der Landwirtschaft (ISO 1401:1999)
Tuyaux en caoutchouc pour pulvérisation agricole (ISO 1401: 1999)
Ta slovenski standard je istoveten z: EN ISO 1401:1999
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 1401
Third edition
1999-12-01
Rubber hoses for agricultural spraying
Tuyaux en caoutchouc pour pulvérisation agricole
A
Reference number
ISO 1401:1999(E)
ISO 1401:1999(E)
Contents Page
1 Scope .1
2 Normative references .1
3 Classification.1
4 Construction and materials .2
5 Dimensions and tolerances .2
5.1 Nominal bore and internal diameter .2
5.2 Length.2
5.3 Minimum thickness of lining and cover .2
6 Physical requirements on samples taken from the hose or from moulded sheets of equivalent
vulcanization .3
6.1 Tensile strength and elongation at break of rubber lining and cover.3
6.2 Requirements after immersion in fluid.3
6.3 Accelerated ageing.3
7 Physical requirements on finished hoses.3
7.1 Change in dimensions .3
7.2 Hydrostatic requirements .3
7.3 Bending-test requirements .4
7.4 Adhesion.4
7.5 Resistance to ozone .4
8 Marking .4
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii
©
ISO ISO 1401:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 1401 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Hoses (rubber and plastics).
This third edition cancels and replaces the second edition (ISO 1401:1987), which has been technically revised.
iii
©
INTERNATIONAL STANDARD  ISO ISO 1401:1999(E)
Rubber hoses for agricultural spraying
1 Scope
This International Standard specifies requirements for three types of flexible rubber hose for
...