FprEN ISO 8028
(Main)Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO/FDIS 8028:2024)
Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO/FDIS 8028:2024)
This document specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
Gummi- und/oder Kunststoffschläuche und ‑schlauchleitungen für das luftfreie Farbspritzen - Spezifikation (ISO/FDIS 8028:2024)
Dieses Dokument legt die Anforderungen an vier Typen von Schläuchen und Schlauchleitungen für die Verwendung beim luftfreien Farbspritzen fest. Die vier Typen werden unterschieden durch Berstdruck und Betriebstemperatur, und können aus Gummi oder Kunststoffmaterialien oder einer Kombination aus Gummi und Kunststoff hergestellt sein.
WARNUNG — Die in diesem Dokument beschriebene Prüfung sollte von erfahrenem Personal durchgeführt werden. In diesem Dokument werden nicht alle Sicherheitsprobleme behandelt, die bei Anwendung der Norm auftreten können. Der Anwender ist für die Einführung geeigneter Maßnahmen zur Einhaltung der Anforderungen an Sicherheit und Gesundheit verantwortlich.
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation (AIRLESS) des peintures - Spécifications (ISO/FDIS 8028:2024)
Le présent document spécifie les exigences relatives à quatre types de tuyaux et flexibles utilisés dans la pulvérisation des peintures sans air. Les quatre types sont différenciés par la pression de rupture et la température d’utilisation, et peuvent être réalisés à partir de matériaux en caoutchouc ou en plastique, ou une combinaison de matériaux en caoutchouc et en plastique.
Gumene in/ali polimerne cevi ter cevni priključki za brezzračno brizganje barve - Specifikacija (ISO/FDIS 8028:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 8028:2023
01-oktober-2023
Gumene in/ali polimerne cevi ter cevni priključki za brezzračno brizganje barve -
Specifikacija (ISO/DIS 8028:2023)
Rubber and/or plastics hoses and hose assemblies for airless paint spraying -
Specification (ISO/DIS 8028:2023)
Gummi- und/oder Kunststoffschläuche und -schlauchleitungen für das luftfreie
Farbspritzen - Spezifikation (ISO/DIS 8028:2023)
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation (AIRLESS) des
peintures - Spécifications (ISO/DIS 8028:2023)
Ta slovenski standard je istoveten z: prEN ISO 8028
ICS:
83.140.40 Gumene cevi Hoses
87.100 Oprema za nanašanje Paint coating equipment
premazov
oSIST prEN ISO 8028:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 8028:2023
oSIST prEN ISO 8028:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8028
ISO/TC 45/SC 1 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-08-03 2023-10-26
Rubber and/or plastics hoses and hose assemblies for
airless paint spraying — Specification
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation (AIRLESS) des peintures —
Spécifications
ICS: 87.100; 83.140.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8028:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 8028:2023
ISO/DIS 8028:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8028
ISO/TC 45/SC 1 Secretariat: DIN
Voting begins on: Voting terminates on:
Rubber and/or plastics hoses and hose assemblies for
airless paint spraying — Specification
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation (AIRLESS) des peintures —
Spécifications
ICS: 87.100; 83.140.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 8028:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 8028:2023
ISO/DIS 8028:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types of hose and hose assemblies . 2
5 Construction and materials .2
6 Dimensions and tolerances .2
7 Performance requirements for finished hose . 2
7.1 Adhesion requirements . 2
7.2 Ultraviolet resistance (plastics cover only) . 3
7.3 Resistance to ozone (rubber cover only) . 3
8 Performance requirements for finished hose and hose assemblies .3
8.1 Hydrostatic requirements . 3
8.2 Impulse test requirements . 3
8.3 Electrical-continuity requirements . 3
9 Physical requirements of lining for hose only . 4
10 Frequency of testing . .4
11 Type testing .4
12 Test report . 4
13 Marking . . 4
14 Recommendations for packaging and storage . 5
Annex A (normative) Type test and routine test . 6
Annex B (informative) Test frequency for production acceptance tests .7
Bibliography . 8
iii
oSIST prEN ISO 8028:2023
ISO/DIS 8028:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 8028:2017), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Clause 8.1 and Table A.2 has been re-written to clarify the conditions for the number of test samples.
— Clause 8.2 has been re-written to make it appropriate minimum bend radius and requirements.
— In Clause 13, year of publication has been deleted and change the unit of working pressure to MPa
as a main unit.
— Update the Normative References.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
oSIST prEN ISO 8028:2023
DRAFT INTERNATIONAL STANDARD ISO/DIS 8028:2023(E)
Rubber and/or plastics hoses and hose assemblies for
airless paint spraying — Specification
WARNING — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices.
1 Scope
This document specifies the requirements for four types of hose and hose assemblies for use in airless
paint spraying. The four types are differentiated by burst pressure and operating temperature, and can
be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817:2015, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 6803, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 7326:2016, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 7751, Rubber and plastics hoses and hose assemblies — Ratios of proof and burst pressure to maximum
working pressure
ISO 8031:2020, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance
and conductivity
ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test
methods
ISO 30013:2011, Rubber and plastics hoses — Methods of exposure to laboratory light sources —
Determination of changes in colour, appearance and other physical properties
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
oSIST prEN ISO 8028:2023
ISO/DIS 8028:2023(E)
4 Types of hose and hose assemblies
Four types of hose and hose assemblies are specified, as follows:
— Type A: Assemblies designed for a maximum working pressure of 200 bar (20 MPa), intended for
spraying paints containing solvents at temperatures from –20 °C to +50 °C.
— Type B: Assemblies designed for a maximum working pressure of 360 bar (36 MPa), intended for
spraying paints containing solvents at temperatures from –20 °C to +50 °C.
— Type C: Assemblies designed for a maximum working pressure of 2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.