EN ISO 19069-1:2015

Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19069-1:2015)

ISO 19069-1:2015 establishes a system of designation for polypropylene (PP) thermoplastic material, which can be used as the basis for specifications.
The types of polypropylene plastics are differentiated from each other by a classification system based on appropriate levels of the designatory properties
a)    tensile modulus of elasticity,
b)    impact strength, and
c)    melt mass-flow rate (MFR),
and on information about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.
ISO 19069-1:2015 is applicable to all polypropylene homopolymers and to copolymers of propylene with a content of other 1-olefinic of less than 50 % (m/m), as well as blends of polymers containing at least 50 % (m/m) of aforementioned polymers.
It applies to materials ready for normal use in the form of powder, granules, or pellets and to materials unmodified or modified by colorants, additives, fillers, etc.
ISO 19069-1:2015 does not apply to propylene-based rubber.

Kunststoffe - Polypropylen (PP)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 19069-1:2015)

1.1   In diesem Teil von ISO 19069 wird ein Bezeichnungssystem für thermoplastische Poly¬propylen (PP)-Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann.
1.2   Polypropylen-Formmasse-Typen werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften
a)   Zugelastizitätsmodul,
b)   Charpy-Kerbschlagzähigkeit,
c)   Schmelze-Massefließrate (MFR)
und Informationen über Parameter der Basispolymere, vorgesehene Anwendung und/oder Verarbeitungs-verfahren, wichtige Eigenschaften, Additive, Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3   Dieser Teil von ISO 19069 ist anwendbar auf alle Polypropylen-Homopolymere und Copolymere des Propylens mit einem Massenanteil an anderen 1 Olefinmonomeren von weniger als 50 % sowie auf Polymermischungen mit einem Massenanteil an obenerwähnten Polymeren von mindestens 50 %.
Er gilt für gebrauchsfertige Formmassen in der Form von Pulver, Granulat oder Pellets sowie für Formmassen, modifiziert oder nicht modifiziert mit Farbstoffen, Additiven, Füllstoffen usw.
Dieser Teil von ISO 19069 ist nicht anwendbar auf Gummi auf Propylenbasis.
1.4   Es sollte nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise auch das gleiche Leistungsverhalten aufweisen. Dieser Teil von ISO 19069 enthält keine technischen Daten, Leistungsangaben oder Daten zu Verarbeitungsbedingungen, die möglicherweise notwendig sind, um eine Formmasse für eine spezielle Anwendung und/oder ein bestimmtes Verarbeitungsverfahren zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften erforderlich sind, müssen sie, soweit möglich, in Übereinstimmung mit den in Teil 2 dieser Internationalen Norm festgelegten Prüfverfahren bestimmt werden.
1.5   Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen zusätzliche Anforderungen im Daten-Block 5 angegeben werden (siehe Abschnitt 3, einleitender Absatz).

Plastiques - Matériaux polypropylène (PP) pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 19069-1:2015)

L'ISO 19069-1:2015 établit un système de désignation des matériaux thermoplastiques polypropylène (PP) qui peut être utilisé comme base pour les spécifications.
Les types de plastiques polypropylène sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation:
a)    module d'élasticité en traction,
b)    résistance au choc, et
c)    indice de fluidité à chaud en masse (MFR),
et des informations concernant les paramètres du polymère de base, l'application prévue et/ou la méthode de mise en ?uvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
L'ISO 19069-1:2015 est applicable à tous les homopolymères et aux copolymères du propylène ayant une teneur en autres monomères 1-oléfiniques inférieure à 50 % (m/m), ainsi qu'aux mélanges de polymères contenant au moins 50 % (m/m) des polymères mentionnés ci-dessus.
Elle s'applique aux matériaux prêts à l'emploi normal sous forme de poudre, de grains ou de granulés, non modifiés ou modifiés par des colorants, des additifs, des charges, etc.
L'ISO 19069-1:2015 ne s'applique pas au caoutchouc à base de propylène.

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz polipropilena - 1. del: Sistem označevanja in osnove za specifikacijo (ISO 19069-1:2015)

Ta del standarda ISO 19069 določa sistem označevanja polipropilenskega (PP) plastomernega materiala, ki ga je mogoče uporabiti kot podlago za specifikacije.
Vrste polipropilenskih polimernih materialov se ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh označevalnih lastnosti:
a) nateznih modulih elastičnosti,
b) udarni trdnosti in
c) prostorninskem pretoku taline (MFR)
ter na informacijah o parametrih osnovnega polimera, nameravani uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih ter materialih za ojačanje.
Ta del standarda ISO 19069 se uporablja za vse polipropilenske homopolimere in kopolimere propilena z manj kot 50 % (m/m) vsebnostjo drugega 1-olefina in tudi mešanice polimerov, ki vsebujejo najmanj 50 % (m/m) omenjenih polimerov.
Uporablja se za materiale v obliki praška, granul ali peletov, pripravljene za običajno uporabo, in materiale, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.
Ta del standarda ISO 19069 se ne uporablja za propilensko gumo.
Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta del standarda ISO 19069 ne zagotavlja inženirskih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so lahko potrebni za določitev materiala za določeno uporabo in/ali metodo obdelave.
Če so take dodatne lastnosti zahtevane, se določijo v skladu s preskusnimi metodami iz standarda ISO 19069-21, če je to primerno.
Da bi se določil termoplastični material za določeno uporabo ali da bi se zagotovila obnovljiva obdelava, je mogoče v podatkovnem bloku 5 navesti dodatne zahteve (glej točko 3.1).

General Information

• Status: Published
• Publication Date: 03-Mar-2015
• Withdrawal Date: 29-Sep-2015
• ICS: 83.080 - Plastics
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 04-Mar-2015
• Completion Date: 04-Mar-2015
• Ref Project: SIST EN ISO 19069-1:2015 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19069-1:2015)

Relations

• Replaces: EN ISO 1873-1:1995 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1873-1:1995)
• Effective Date: 11-Mar-2015

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2015
1DGRPHãþD
SIST EN ISO 1873-1:1999
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]SROLSURSLOHQD
GHO6LVWHPR]QDþHYDQMDLQRVQRYH]DVSHFLILNDFLMR,62
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation
system and basis for specifications (ISO 19069-1:2015)
Kunststoffe - Polypropylen (PP)-Formmassen - Teil 1: Bezeichnungssystem und Basis
für Spezifikationen (ISO 19069-1:2015)
Plastiques - Matériaux polypropylène (PP) pour moulage et extrusion - Partie 1: Système
de désignation et base de spécification (ISO 19069-1:2015)
Ta slovenski standard je istoveten z: EN ISO 19069-1:2015
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 19069-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 83.080.20 Supersedes EN ISO 1873-1:1995
English Version
Plastics - Polypropylene (PP) moulding and extrusion materials -
Part 1: Designation system and basis for specifications (ISO
19069-1:2015)
Plastiques - Matériaux polypropylène (PP) pour moulage et Kunststoffe - Polypropylen (PP)-Formmassen - Teil 1:
extrusion - Partie 1: Système de désignation et base de Bezeichnungssystem und Basis für Spezifikationen (ISO
spécification (ISO 19069-1:2015) 19069-1:2015)
This European Standard was approved by CEN on 10 January 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19069-1:2015 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 19069-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1873-1:1995.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19069-1:2015 has been approved by CEN as EN ISO 19069-1:2015 without any modification.

INTERNATIONAL ISO
STANDARD 19069-1
First edition
2015-03-01
Plastics — Polypropylene (PP)
moulding and extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux polypropylène (PP) pour moulage et
extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 19069-1:2015(E)
©
ISO 2015
ISO 19069-1:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

ISO 19069-1:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Designation and specification system . 2
3.1 General . 2
3.2 Data block 1 . 2
3.3 Data block 2 . 3
3.4 Data block 3 . 4
3.5 Data block 4 . 4
3.5.1 General. 4
3.5.2 Tensile modulus of elasticity . 5
3.5.3 Charpy impact strength . 5
3.5.4 Melt mass-flow rate . 6
3.6 Data block 5 . 6
4 Examples of designations . 6
4.1 Designation only . 6
4.2 Designation transformed into a specification . 8
Bibliography .10
ISO 19069-1:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This first edition of ISO 19069-1 cancels and replaces ISO 1873-1:1995, which has been technically
revised to introduce a new designation system.
ISO 19069 consists of the following parts, under the general title Plastics — Polypropylene (PP) moulding
and extrusion materials:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test specimens and determination of properties
iv © ISO 2015 – All rights reserved

INTERNATIONAL STANDARD ISO 19069-1:2015(E)
Plastics — Polypropylene (PP) moulding and extrusion
materials —
Part 1:
Designation system and basis for specifications
1 Scope
This part of ISO 19069 establishes a system of designation for polypropylene (PP) thermoplastic
material, which can be used as the basis for specifications.
The types of polypropylene plastics are differentiated from each other by a classification system based
on appropriate levels of the designatory properties
a) tensile modulus of elasticity,
b) impact strength, and
c) melt mass-flow rate (MFR),
and on information about basic polymer parameters, intended application and/or method of processing,
important properties, additives, colorants, fillers, and reinforcing materials.
This part of ISO 19069 is applicable to all polypropylene homopolymers and to copolymers of propylene
with a content of other 1-olefinic of less than 50 % (m/m), as well as blends of polymers containing at
least 50 % (m/m) of aforementioned polymers.
It applies to materials ready for normal use in the form of powder, granules, or pellets and to materials
unmodified or modified by colorants, additives, fillers, etc.
This part of ISO 19069 does not apply to propylene-based rubber.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This part of ISO 19069 does not provide engineering data, performance data, or data on
processing conditions which can be required to specify a material for a particular application and/or
method of processing.
If such additional properties are required, they shall be determined in accordance with the test methods
1)
specified in ISO 19069-2 , if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, additional requirements can be given in data block 5 (see 3.1).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics
1) To be published.
-------------
...