Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21301-2:2019)

This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of ethylene/vinyl acetate (EVAC) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given in this document.
This document gives procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made. Properties and test methods which are suitable and necessary to characterize EVAC moulding and extrusion materials are listed in this document.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for or of particular significance to these moulding and extrusion materials are also included in this document, as are the designatory properties specified in ISO 21301-1.
The methods of preparation and conditioning, the specimen dimensions and the test procedures specified this document are used in order to obtain reproducible and comparable test results. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Kunststoffe - Ethylen-Vinylacetat (E/VAC)-Werkstoffe - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 21301-2:2019)

Plastiques - Matériaux à base de copolymère éthylène-acétate de vinyle (EVAC) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 21301-2:2019)

Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai qui doivent être utilisées pour la détermination des propriétés des matériaux pour moulage et extrusion à base d'EVAC. Les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai sont indiquées dans ce document.
Le présent document donne les modes opératoires et les conditions pour la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues. Les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base d'EVAC sont énumérées dans le présent document.
Les propriétés ont été sélectionnées parmi les méthodes d'essai générales de l'ISO 10350‑1. D'autres méthodes d'essai largement en usage ou ayant une signification particulière pour ces matériaux pour moulage et extrusion sont aussi incluses dans le présent document; c'est le cas des propriétés de désignation spécifiées dans l'ISO 21301‑1.
Les méthodes de préparation et de conditionnement, les dimensions d'éprouvette ainsi que les modes opératoires d'essai spécifiés dans ce document sont utilisés dans le but d'obtenir des résultats d'essai reproductibles et comparables. Les valeurs déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.

Polimerni materiali - Materiali na osnovi polibutena-1 (PB-1) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 21301-2:2019)

Ta dokument določa metode za pripravo preskušancev in preskusnih metod za uporabo pri ugotavljanju lastnosti materialov na osnovi kopolimerov etilen/vinilacetata (EVAC) za oblikovanje in ekstrudiranje.
Podane so zahteve za ravnanje s preskusnim materialom ter obdelavo preskusnega materiala pred oblikovanjem
in preskušancev pred preskušanjem.
Ta dokument podaja postopke in pogoje za pripravo preskušancev ter postopke za merjenje lastnosti materialov, iz katerih so izdelani preskušanci. V tem dokumentu so navedene lastnosti in preskusne metode, ki so primerne in nujne za opredelitev materialov na osnovi kopolimerov etilen/vinilacetata za oblikovanje in ekstrudiranje.
Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki so v splošni uporabi ali so posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v ta dokument. Vključene so tudi označevalne lastnosti, določene v standardu ISO 21301-1.
Metode priprave in obdelave, mere preskušancev in preskusni postopki, določeni v tem dokumentu, se uporabljajo za pridobitev ponovljivih in primerljivih rezultatov preskušanj. Pri tem ni nujno, da bodo ugotovljene vrednosti
enake tistim, ki so pridobljene z uporabo preskušancev, ki imajo drugačne mere ali so pripravljeni z uporabo drugih postopkov.

General Information

Status
Published
Publication Date
05-Mar-2019
Withdrawal Date
29-Sep-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
06-Mar-2019
Completion Date
06-Mar-2019

Relations

Buy Standard

Standard
EN ISO 21301-2:2019
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2019
1DGRPHãþD
SIST EN ISO 4613-2:1999
SIST EN ISO 4613-2:1999/A1:2004
Polimerni materiali - Materiali na osnovi polibutena-1 (PB-1) za oblikovanje in
ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 21301-
2:2019)
Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of
test specimens and determination of properties (ISO 21301-2:2019)
Kunststoffe - Ethylen-Vinylacetat (E/VAC)-Werkstoffe - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO 21301-2:2019)
Plastiques - Matériaux à base de polybutène-1 (PB-1) pour moulage et extrusion - Partie
2: Préparation des éprouvettes et détermination des propriétés (ISO 21301-2:2019)
Ta slovenski standard je istoveten z: EN ISO 21301-2:2019
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 21301-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2019
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 4613-2:1995
English Version
Plastics - Ethylene-vinyl acetate (EVAC) moulding and
extrusion materials - Part 2: Preparation of test specimens
and determination of properties (ISO 21301-2:2019)
Plastiques - Matériaux à base de copolymère éthylène- Kunststoffe - Ethylen-Vinylacetat (E/VAC)-Werkstoffe -
acétate de vinyle (EVAC) pour moulage et extrusion - Teil 2: Herstellung von Probekörpern und Bestimmung
Partie 2: Préparation des éprouvettes et détermination von Eigenschaften (ISO 21301-2:2019)
des propriétés (ISO 21301-2:2019)
This European Standard was approved by CEN on 9 February 2019.

This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 20 March 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N

EUROPÄISCHES KOMITEE FÜR NORMUN G

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21301-2:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 21301-2:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4613-2:1995.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 21301-2:2019 has been approved by CEN as EN ISO 21301-2:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 21301-2
First edition
2019-02
Plastics — Ethylene-vinyl acetate
(EVAC) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux à base de copolymère éthylène-acétate de
vinyle (EVAC) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 21301-2:2019(E)
©
ISO 2019
ISO 21301-2:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 21301-2:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of the material before moulding . 3
4.3 Compression moulding . 3
5 Conditioning of test specimens . 3
6 Determination of properties . 3
Bibliography . 9
ISO 21301-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
This first edition of ISO 21301-2 cancels and replaces the second edition of ISO 4613-2:1995, which has
been technically revised to introduce a new designation system. It also incorporates the Amendment
ISO 4613-2:1995/Amd.1:2004. The main changes compared to the previous edition are as follows:
— the normative references has been updated;
— the contents and structures of Table 2 and Table 3 have been revised according to the revised
ISO 10350-1.
A list of all parts in the ISO 21301 series can be found on the ISO website.
iv © ISO 2019 – All rights reserved

INTERNATIONAL STANDARD ISO 21301-2:2019(E)
Plastics — Ethylene-vinyl acetate (EVAC) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods to be used
in determining the properties of ethylene/vinyl acetate (EVAC) moulding and extrusion materials.
Requirements for handling test material and for conditioning both the test material before moulding
and the specimens before testing are given in this document.
This document gives procedures and conditions for the preparation of test specimens and procedures
for measuring properties of the materials from which these specimens are made. Properties and test
methods which are suitable and necessary to characterize EVAC moulding and extrusion materials are
listed in this document.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for or of particular significance to these moulding and extrusion materials are also included in
this document, as are the designatory properties specified in ISO 21301-1.
The methods of preparation and conditioning, the specimen dimensions and the test procedures
specified this document are used in order to obtain reproducible and comparable test results. Values
determined will not necessarily be identical to those obtained using specimens of different dimensions
or prepared using different procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 21301-2:2019(E)
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR)
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.