Machines for underground mines - Mobile machines working underground - Safety - Part 2: Rail locomotives

This European standard specifies the safety requirements and tests for locomotives for use in underground mining (i.e. mine locomotives) and other underground workings (e.g. tunnelling locomotives). This European standard identifies and takes account of the hazards arising from the use in mines and other underground workings of such equipment and describes methods for the elimination or reduction of these hazards, and for the safeguarding of personnel and machinery. These hazards are listed under clause 4.

Maschinen für den Bergbau unter Tage - Bewegliche Maschinen für die Verwendung unter Tage - Sicherheit - Teil 2: Lokomotiven

1.1   Diese Europäische Norm legt die Sicherheitsanforderungen an und Prüfungen von Lokomotiven fest, die zur Verwendung im Bergbau unter Tage (d. h. Grubenlokomotiven) und weiteren Untertagearbeiten (z. B. Tunnel-lokomotiven) bestimmt sind.
1.2   Diese Europäische Norm befasst sich mit den technischen Anforderungen, die erforderlich sind, um die im Abschnitt 4 aufgeführten Gefahren zu minimieren, die während der Inbetriebnahme, des Betriebes und der Wartung der Lokomotiven wenn diese Vorgänge in Übereinstimmung mit den vom Hersteller oder seinem autorisierten Vertreter angegebenen Spezifikationen ausgeführt werden.
Diese Europäische Norm berücksichtigt nicht besondere Gefährdungen, die von Triebstock- oder Zahnradloko-motiven ausgehen.
1.3   Diese Europäische Norm behandelt nicht Strahlung und Vibration. Sie berücksichtigt nicht ferngesteuerte Lokomotiven oder Betrieb in potentiell explosibler Atmosphäre. Gefährdungen durch Lärm sind in dieser Norm aus-geschlossen. Eine gesonderte Norm ist in Vorbereitung, in der Gefährdungen durch Lärm behandelt werden.
1.4   Diese Europäische Norm gilt für Lokomotiven, die nach Inkrafttreten dieser Norm hergestellt werden.

Machines pour l'exploitation de mines souterraines - Machines mobile souterraines - Sécurité - Partie 2: Locomotives sur rails

La présente norme européenne spécifie les prescriptions de sécurité et essais des locomotives sur rails utilisées pour l'exploitation de mines souterraines (par exemple, locomotives de fond) et autres travaux souterrains (par exemple, locomotives pour tunnelier). La présente norme européenne identifie et prend en compte les risques engendrés par l'utilisation dans des mines et autres exploitations souterraines de tels équipements, et décrit également des méthodes d'élimination ou de réduction de ces risques, ainsi que de protection du personnel et des machines.

Stroji za podzemne rudnike – Mobilni stroji za podzemne rudnike – Varnost – 2. del: Tirne lokomotive

General Information

Status
Withdrawn
Publication Date
10-Jun-2003
Withdrawal Date
31-Mar-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Apr-2009
Completion Date
01-Apr-2009

Relations

Buy Standard

Standard
EN 1889-2:2004
English language
48 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1889-2:2004
01-junij-2004
Stroji za podzemne rudnike – Mobilni stroji za podzemne rudnike – Varnost – 2.
del: Tirne lokomotive
Machines for underground mines - Mobile machines working underground - Safety - Part
2: Rail locomotives
Maschinen für den Bergbau unter Tage - Bewegliche Maschinen für die Verwendung
unter Tage - Sicherheit - Teil 2: Lokomotiven
Machines pour l'exploitation de mines souterraines - Machines mobile souterraines -
Sécurité - Partie 2: Locomotives sur rails
Ta slovenski standard je istoveten z: EN 1889-2:2003
ICS:
73.100.40 Oprema za vleko in dviganje Haulage and hoisting
equipment
SIST EN 1889-2:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 1889-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2003
ICS 73.100.40
English version
Machines for underground mines - Mobile machines working
underground - Safety - Part 2: Rail locomotives
Machines pour l'exploitation de mines souterraines - Maschinen für den Bergbau unter Tage - Bewegliche
Machines mobile souterraines - Sécurité - Partie 2: Maschinen für die Verwendung unter Tage - Sicherheit -
Locomotives sur rails Teil 2: Lokomotiven
This European Standard was approved by CEN on 13 February 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1889-2:2003 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 1889-2:2003 (E)
Contents
Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions.7
4 List of significant hazards.8
5 Safety requirements and/or safety measures.11
6 Verification of safety requirements.24
7 Information for use .25
Annex A (normative) Illuminance requirements for locomotive headlights .30
Annex B (normative) Brake testing .35
Annex C (normative) Dimensions of locomotive drivers' cabs.38
Annex D (normative) Verification data for safety requirements.41
Annex E (normative) Model form for description of underground locomotives .45
Annex ZA (informative) Relationship of this European Standard with EC Directives.47
Bibliography .48
2

---------------------- Page: 3 ----------------------

EN 1889-2:2003 (E)
Foreword
This document (EN 1889-2:2003) has been prepared by Technical Committee CEN/TC 196, "Machines for
underground mines - Safety", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by December 2003, and conflicting national standards shall be withdrawn at the latest
by December 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative annex ZA, which is an integral part of this document.
Annexes A, B, C, D and E are normative.
This document includes a Bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
3

---------------------- Page: 4 ----------------------

EN 1889-2:2003 (E)
Introduction
This European Standard is a type C standard as stated in EN 1070.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated
in the scope of this document.
The standard takes into account the current state of the art and technical facilities to use in order to exclude or prevent,
as far as possible, hazards when rail locomotives are used underground.
When compiling this standard it has been assumed that:
components are:
a) designed in accordance with good engineering practice, taking account of expected shocks and vibrations and
calculation codes, including all failure modes;
b) of sound mechanical and electrical construction;
c) made of materials with adequate strength and of suitable quality; and
d) free of defects.
harmful materials, such as asbestos are not used;
components are kept in good repair and working order, so that the required dimensions remain fulfilled despite
wear;
negotiations have taken place between the manufacturer or authorised representative, purchaser and/or user
(e.g. for fire resistant fluids, safety equipment and load restraining devices).
4

---------------------- Page: 5 ----------------------

EN 1889-2:2003 (E)
1 Scope
1.1 This European standard specifies the safety requirements and tests for rail locomotives for use in
underground mining (i.e. mine locomotives) and other underground workings (e.g. tunnelling locomotives).
1.2 This European standard deals with the technical requirements to minimise the hazards listed in clause 4
which can arise during the commissioning, the operation and the maintenance of locomotives when carried out in
accordance with the specifications given by the manufacturer or his authorised representative.
This European standard does not address the special hazards associated with the rack drive of rack and pinion
locomotives.
1.3 This European standard does not deal with radiation and vibration. It does not address remote control
locomotives or operation in potentially explosive atmospheres. Hazards due to noise are excluded from this
.
standard, but a separate standard is in preparation where hazards due to noise will be addressed 1.4 This
European standard applies to locomotives which are manufactured after the date of issue of this standard.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 292-1:1991, Safety of machinery — Basic concepts, general principles for design - Part 1: Basic terminology,
methodology
EN 292-2:1991 + EN 292-2:1991/A1:1995, Safety of machinery — Basic concepts, general principles for design —
Part 2: Technical principles and specifications
EN 294, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs
EN 349, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
EN 418:1992, Safety of Machinery — Emergency stop equipment, functional aspects — Principles for design
EN 457, Safety of machinery — Auditory danger signals — General requirements, design and testing (ISO 7731:1986,
modified).
EN 547-1, Safety of machinery — Human body measurements — Part 1: Principles for determining the dimensions
required for openings for whole body access into machinery
EN 547-2, Safety of machinery — Human body measurements — Part 2: Principles for determining the dimensions
required for access openings
EN 547-3, Safety of machinery — Human body measurements — Part 3: Anthropometric data
5

---------------------- Page: 6 ----------------------

EN 1889-2:2003 (E)
EN 563, Safety of machinery — Temperatures of touchable surfaces — Ergonomics data to establish temperature
limit values for hot surfaces
EN 894-1, Safety of machinery — Ergonomic requirements for the design of displays and control actuators — Part 1:
General principles for human interactions with displays and control actuators
EN 894-2, Safety of machinery — Ergonomic requirements for the design of displays and control actuators — Part 2:
Displays
EN 894-3, Safety of Machinery — Ergonomic requirements for the design of displays and control actuators — Part 3:
Control actuators
EN 953, Safety of machinery — Guards — General requirements for the design and construction of fixed and
moveable guards
EN 954-1, Safety of machinery — Safety related parts of control systems — Part 1: General principles for design
EN 982, Safety of machinery — Safety requirements for fluid power systems and their components — Hydraulics
EN 983, Safety of machinery — Safety requirements for fluid power systems and their components — Pneumatics
EN 1050:1996, Safety of machinery – Principles for risk assessment.
EN 1070:1998, Safety of machinery — Terminology
EN 1679-1, Reciprocating internal combustion engines — Safety — Part 1: Compression ignition engines
EN 13202:2000, Ergonomics of the thermal environment — Temperatures of touchable hot surfaces - Guidance for
establishing surface temperature limit values in production standards with the aid of EN 563
EN 60204-1:1998, Safety of Machinery — Electrical equipment of machines — Part 1: General requirements
EN ISO 3411, Earth-moving machinery — Human physical dimensions of operators and minimum operator space
envelope (ISO 3411:1995)
EN ISO 8030, Rubber and plastic hoses — Method of test for flammability
ISO 1813, Belt drives — V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts
— Electrical conductivity of antistatic belts: Characteristics and methods of test
ISO 3864, Safety colours and safety signs
ISO 6405-1, Operation and maintenance of earth moving machinery — Specification for common symbols for operator
controls and other displays
ISO 6405-2, Earth-moving machinery – Symbols for operator controls and other displays - Part 2: Specific symbols for
machines, equipment and accessories.
ISO 6805, Rubber hoses and hose assemblies for underground mining — Wire-reinforced hydraulic types for coal
mining — Specification
IEC 60332-1, Tests on electric cables under fire conditions — Part 1: Test on a single vertical insulated wire or
cable
6

---------------------- Page: 7 ----------------------

EN 1889-2:2003 (E)
3 Terms and definitions
For the purposes of this European Standard, the following terms and definitions together, where appropriate, with those
in EN 1070:1998 apply:
3.1
locomotive
self-powered uncaptivated vehicle running on a track of rails underground in mines or other underground workings,
designed for hauling persons, materials or mineral
3.2
driver
designated person suitably trained, qualified by knowledge and practical experience and provided with the necessary
instructions to ensure safe operation of the locomotive
3.3
service weight
sum of
the weight of the serviceable locomotive;
the weight of the driver (800 N);
two-thirds of the weight of the fuel stock.
3.4
braked weight
service weight of the locomotive less the weight of any unbraked wheels and the weight carried by them
3.5
brake ratio
ratio of the brake force acting between the locomotive and the rails against the direction of travel, and the braked
weight of the locomotive
3.6
skidding
when the circumferential speed of braked wheels is lower than the speed of the locomotive beyond the normal creep
speed. In the extreme case the circumferential speed is zero (wheels locked)
3.7
slipping
when the circumferential speed of driven wheels is greater than the speed of the locomotive beyond the normal
creep speed of the driven wheels
3.8
battery locomotive
electric locomotive which obtains its power from a battery or batteries
3.9
trolley locomotive
electric locomotive which obtains its power from a roadway conductor
7

---------------------- Page: 8 ----------------------

EN 1889-2:2003 (E)
3.10
battery/trolley (compound) locomotive
electric locomotive which obtains its power either from a battery or from a roadway conductor
3.11
diesel locomotive
diesel locomotive which obtains its power from a reciprocating internal combustion engine
3.12
mid-point switch disconnector
device designed to disconnect the power of a traction battery at a place where the voltage between the positive take-off
lead and the mid-point switch disconnector is approximately equal to that between the mid-point switch disconnector
and the negative take-off lead
3.13
braking systems
all the elements which combine together to brake and hold the locomotive. Such systems consist of a control,
means of power transmission and the brake itself
3.13.1
service braking system
primary system used for stopping and holding the locomotive
3.13.2
emergency braking system
additional braking system other than the service braking system, that can be applied manually or automatically to stop
the locomotive
3.13.3
parking braking system
system used to hold a stopped locomotive in the stationary condition
3.14
firedamp
flammable gas, consisting mainly of methane, found naturally in mines
4 List of significant hazards
Table 1 contains all the significant hazards, hazardous situations and events, as far as they are dealt with in this
standard, identified by risk assessment as significant for this type of machinery and which require action to
eliminate or reduce the risk.
8

---------------------- Page: 9 ----------------------

EN 1889-2:2003 (E)
Table 1 — List of significant hazards with associated requirements
EN 1050:1996, Hazards according to EN 1050:1996, Relevant clause/subclause of
annex A annex A this standard
1 Mechanical hazards due to: 5.1, 5.1.7, 5.2, 5.3, 5.13
- machine parts or workpieces, e.g.:
a) shape;
b) relative location;
c) mass and stability;
e) inadequacy of mechanical strength;
1.1 Crushing hazard 5.1.2, 5.1.3, 5.3, 5.13
1.2 Shearing hazard 5.1.2, 5.1.3, 5.3, 5.13
1.3 Cutting or severing hazard 5.1.2, 5.1.3, 5.13
1.4 Entanglement hazard 5.1.2, 5.1.3
1.5 Drawing-in or trapping hazard 5.1.2, 5.1.3, 5.13
1.6 Impact hazard 5.1.2, 5.1.3, 5.1.5, 5.3, 5.13
1.7 Stabbing or puncture hazard 5.1.2, 5.1.3, 5.13
1.8 Friction or abrasion hazard 5.1.2, 5.1.3, 5.13
1.9 High pressure fluid injection or ejection 5.4.1, 5.4.2
hazard
2 Electrical hazard due to:
2.1 Contact of person with live parts (direct 5.5
contact)
2.2 Contact of person with parts which have 5.5
become live under faulty conditions (indirect
contact)
2.4 Electrostatic phenomena 5.5.1
3 Thermal hazards, resulting in:
3.1 Burns and scalds by contact with objects or 5.1, 5.4.1,5.4.2, 5.14
materials with an extreme high or low
temperature, by flames or explosions and
also by the radiation of heat sources
3.2 Damage to health by hot or cold working 5.13
environment
7 Hazards generated by materials and
(and their constituent
substances
elements) processed or used by the
machinery
7.1 Hazards from contact with or inhalation of 5.4.1, 5.4.2, 5.6
harmful fluid, gases, mists, fumes and dusts
7.2 Fire or explosion hazard 5.4.2, 5.5, 5.6, 5.7, 5.14
8 Hazards generated by neglecting
ergonomic principles in machinery
design, e.g. hazards from:
8.1 Unhealthy postures or excessive effort 5.12, 5.13
8.2 Inadequate consideration of hand-arm or 5.13
foot-leg anatomy
8.4 Inadequate area lighting 5.8
8.5 Mental overload and underload, stress 5.12
8.6 Human error 5.12
9

---------------------- Page: 10 ----------------------

EN 1889-2:2003 (E)
Table 1 — List of significant hazards with associated requirements (continued)
EN 1050:1996, Hazards according to EN 1050:1996, Relevant clause/subclause of
annex A annex A this standard
10 Unexpected start-up/over-run/over-
speed (or any similar malfunction) from:
10.1 Failure/disorder of control supply 5.4, 5.5, 5.11, 5.12
11 Impossibility of stopping the machine in the 5.10, 5.11
best possible conditions
13 Failure of the power supply 5.4, 5.5, 5.6, 5.11, 5.12
14 Failure of the control circuit 5.4, 5.5, 5.11, 5.12
15 Errors of fitting 7.1.1, 7.1.2, 7.1.4
17 Falling or ejected objects or fluids 5.4
18 Loss of stability/overturning of machinery 5.1, 5.2, 5.3, 5.13
20 Relating to the travelling function:
20.1 Movement when starting the engine 5.11,
20.2 Movement without a driver at the driving 5.11.4.4
position
20.3 Movement without all parts in a safe 5.12.1.2
position
20.5 Excessive oscillations when moving 5.1.4
20.6 Insufficient ability of machinery to be 5.11, 5.12
slowed down, stopped and immobilised
21 Linked to the work position (inc. driving
station) on machine:
21.1 Fall of persons during access to (or at/from) 5.13.3, 5.13.5
the work position
21.2 Exhaust gases/lack of oxygen at the work 5.6.1, 5.6.2, 5.6.3
position
21.3 Fire (flammability of the cab, lack of 5.13, 5.14
extinguishing means)
21.4 Mechanical hazards at the work position:
c) fall of objects, penetration by objects; 5.13
21.5 Insufficient visibility from the work positions 5.13
21.6 Inadequate lighting 5.8, 5.12.3.5
21.7 Inadequate seating 5.13.7
22 Due to the control system:
22.1 Inadequate location of manual controls 5.12
22.2 Inadequate design of manual controls and 5.12
their mode of operation
23 From handling the machine (lack of 5.1.4
stability)
24 Due to the power source and to the
transmission of power:
24.1 Hazards from the engine and the batteries 5.5, 5.6
24.3 Hazards from couplings and towing 5.1, 5.3
25 From/to third persons:
25.1 Unauthorised start-up/use 5.12
10

---------------------- Page: 11 ----------------------

EN 1889-2:2003 (E)
Table 1 — List of significant hazards with associated requirements (continued)
EN 1050:1996, Hazards according to EN 1050:1996, Relevant clause/subclause of
annex A annex A this standard
25.3 Lack or inadequacy of visual or acoustic 5.9
warning means
26 Insufficient instructions for the 7.1, 7.3
driver/operator
29 Hazards generated by neglecting
ergonomic principles
29.1 Insufficient visibility from the driving 5.13.1, 5.13.4, 5.13.6
position
30 Mechanical hazards/events due to:
30.2 Failing accelerator or brake control of 5.11, 5.12
machinery running on rails
30.3 Failing or lack of deadman’s control of 5.11.1.7
machinery running on rails
32 Fire and explosion 5.4, 5.5, 5.6, 5.7, 5.14
33 Emission of dust, gases etc. 5.6
5 Safety requirements and/or safety measures
5.1 General/basic requirements
5.1.1 For the application of EN 953, EN 982, EN 983, EN 457, EN 563, EN 547 and
EN 60204-1 the manufacturer shall carry out an adequate risk assessment for the requirements thereof where
choice is necessary.
NOTE This specific risk assessment is part of the general risk assessment relating to the hazards not covered by this C
standard.
For hazards which are not covered by this standard, machinery shall conform as appropriate to EN 292.
5.1.2 All moving parts, with the exception of the wheels, drive lines and articulation area, shall be provided with
guards according to EN 953.
Gaps between guards and moving parts shall conform to EN 349 and EN 294.
5.1.3 Where hinged guards or covers can self-close, they shall be fitted with a support system to secure them in
the open position.
5.1.4 Locomotives shall be fitted with suspension and shock absorbing systems to ensure that all wheels
maintain contact with the rails and to absorb shock loading from the track. In the event of failure of the suspension
system, no part of the locomotive shall contact moving parts of the running gear or be below than the upper level of
the rails. This also applies to driver's cabs having their own bogie, e.g. driver's cabs of articulated locomotives.
NOTE Suspension systems with self-damping, e.g. multi-leaf springs, may not need a separate shock absorbing system.
5.1.5 The front faces of locomotives shall be painted in a safety colour in accordance with ISO 3864.
Locomotives shall have facilities for stowing any safety equipment (see also introduction, on negotiations).
5.1.6 For unintentional contact the temperature of hot surfaces inside of the locomotive are based on annex B of
EN 13202:2000 for 0,5 s contact time. For the parts that require handling during maintenance the temperature of
the touchable surface shall be in accordance with EN 563 for 5 s contact time. Where this limit cannot be
achieved, see 7.1.3.
11

---------------------- Page: 12 ----------------------

EN 1889-2:2003 (E)
Exhaust pipes within reach during operation which exceed the touchable surface temperatures given in EN 13202 for
0,5 s shall be guarded against unintentional contact in accordance with EN 953.
5.1.7 With the exception of couplings and the current collector (for trolley locomotives), all other components
shall be contained within the profile of the locomotive such that they are protected against accidental damage.
5.2 Design to facilitate handling
Where purpose-designed attachment points are provided they shall be designed to have a calculated minimum factor
of safety of 4 on ultimate breaking load in relation to their intended load carrying capacity. They shall be shaped to suit
the lifting means intended by the manufacturer, see 7.1.2. They shall be clearly and permanently marked with their load
carrying capacity, e.g. by welding. Where any such attachment points could be used to lift or move the whole
locomotive this factor of safety shall relate to the service weight of the locomotive.
Articulated locomotives shall be fitted with means to avoid relative movements between parts.
5.3 Couplings
5.3.1 Locomotives shall be equipped with couplings to absorb and to transfer the tensile and compressive forces
to the locomotive frame. The couplings and all parts of the locomotive lying in line with it shall be designed with a
minimum safety factor of 10 against failure in relation to the maximum drawbar pull of the locomotive (or
locomotives where these are designed to be used in tandem), for a minimum coefficient of static friction of 0,25 for
steel tyres and 0,40 for rubber or polymer derivative tyres.
NOTE Characteristics of the coupling are discussed between the manufacturer and the user, see introduction on
negotiation.
5.3.2 In the fully compressed position of the coupling, it shall be possible to move freely a non-deformable
sphere of 250 mm diameter between the front face of the locomotive and a vertical plane perpendicular to the
longitudinal axis of the locomotive at the extreme end of the coupling.
5.3.3 If it is intended that safety chains are to be used the attachment points of these shall have a minimum
breaking strength of not less than 2½ times the weight of the locomotive.
5.4 Fluid power systems
5.4.1 Hydraulic systems
5.4.1.1 Hydraulic systems shall be designed and installed to conform to EN 982.
5.4.1.2 Hydraulic systems (hydrostatic and hydrokinetic) shall be designed to enable non-toxic fluids as
defined in the 7th SHCMOEI Report [1] to be used to minimize risks to health.
5.4.1.3 Hydraulic systems (hydrostatic and hydrokinetic) on locomotives shall be designed such that fire-
th
resistant fluids can be used to minimise fire hazards (ISO 7745 and SHCMOEI 7 report) or the following
precautions shall be taken for all systems exceeding 10 l total capacity:
a) Hydraulic lines (rigid metal and flexible pipelines) shall be segregated from any unprotected electrical cable or
equipment (see 5.5.2.3), or any part of the locomotive, the surface of which, can become sufficiently hot to
reach 80 % of the flashpoint of the hydraulic fluid for which the system has been designed.
b) Hydraulic lines shall be shrouded to prevent flammable fluid under pressure being ejected from a leak or a
burst onto a hot surface as defined in paragraph a) above, or outside the profile of the locomotive.
NOTE National legislation implementing EU Directive 92/104/EEC can require the use of fire resistant fluids in hydraulic
systems, see introduction on negotiation.
5.4.1.4 Hydropneumatic accumulators shall conform to EN 982.
12

---------------------- Page: 13 ----------------------

EN 1889-2:2003 (E)
5.4.1.5 Reservoirs for hydraulic fluids shall be protected against corrosion, be secured to the locomotive and
incorporated in such a way (e.g. inside the rigid structure of the locomotive) that they are protected against
mechanical damage.
5.4.1.6 The filling apertures of reservoirs for hydraulic fluids shall be within reach of an operator standing at rail
level, otherwise means of access shall be provided. The filling aperture shall be designed and positioned in such a
way that any overflow or escape of hydraulic fluid is prevented under foreseeable operating conditions, including
derailment.
Any cap fitted shall be secured to prevent it working loose in service and shall require an intentional action to release it.
When released it shall remain permanently attached to the locomotive.
The location and marking of the filling point for any hydraulic system shall be designed to avoid the inadvertent
introduction of other substances (e.g. liquid fuel, water, sand) into the hydraulic system.
5.4.1.7 Reservoirs for fluids shall have a drainage device at their lowest point. Provision shall be made for free flow and
safe catchment of fluid without coming into the proximity of hot parts or electrical equipment. The design intent shall be
to prevent any fluid residues collecting in parts of the locomotive outside the hydraulic system.
5.4.1.8 Hydraulic pressure relief valves shall only allow hydraulic fluid to be discharged back into the system.
5.4.1.9 Hydraulic lines shall be designed as rigid metal lines or as flexible hoses.
Materials for hydraulic hoses and their components shall be in accordance with ISO 6805 and shall be fire-resistant so
that it will self extinguish within 30 s of removal of the flame in accordance with EN ISO 8030. Safety factors of the hose
assembly (including end fittings), shall be 2:1 for the dynamic pressure and 3:1 for burst pressure.
Hydraulic lines shall be designed to take into account the relative movement between components.
NOTE Where hose re-inforced with steel wire is used consideration needs to be given to fatigue aspects.
Hydraulic hoses containing fluid with a pressure exceeding 5 MPa (50 bar) and/or having a temperature exceeding
50 °C and located within 1 m of the driver or operator shall be guarded, see 5.1.1 and 5.1.2. Parts or components can
be considered as guards.
NOTE Line connections should be limited in number and designed to minimise any possibility of leakage during operation.
5.4.1.10 Tanks for hydraulic fluid shall be fitted with a mechanically protected fluid level indicator with at least
minimum and maximum operating levels.
5.4.1.11 Means shall be provided to monitor hydraulic fluid temperature and to warn the driver when the fluid
temperature approaches the maximum specified by the manufacturer (see also 5.14).
5.4.1.12 The design of the system shall be such that overheating of the fluid beyond the fluid and component
manufacturer’s rated temperature is not exceeded.
5.4.2 Pneumatic systems
5.4.2.1 Pneumatic systems shall be designed and installed in accordance with EN 983.
5.4.2.2 Compressors shall be designed to operate either on a lubricant which is resistant to carbonization (e.g.
synthetic oils), or fitted with temperature monitoring.
5.4.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.