EN ISO 6414:2020
(Main)Technical product documentation (TPD) - Technical drawings for glassware (ISO 6414:2020)
Technical product documentation (TPD) - Technical drawings for glassware (ISO 6414:2020)
This document establishes rules and conventions for particular use with technical drawings on glassware, for example, laboratory glassware or glassware used in other technical fields.
Optical parts are not, however, included herein.
Technische Produktdokumentation (TPD) - Technische Zeichnungen für Glasgeräte (ISO 6414:2020)
Dieses Dokument legt Regeln und Vereinbarungen für den besonderen Gebrauch von technischen Zeichnungen für Glasgeräte fest, z. B. Laborgeräte aus Glas oder Glasgeräte für den Einsatz in anderen technischen Bereichen.
Optische Teile sind in dieser Norm jedoch nicht enthalten.
Documentation technique de produits (DTP) - Dessins techniques de verrerie (ISO 6414:2020)
Le présent document établit des règles et des conventions à l'usage particulier des dessins techniques de la verrerie, par exemple la verrerie de laboratoire, ou la verrerie utilisée dans d'autres domaines techniques.
Toutefois, les parties optiques ne sont pas incluses.
Tehnična dokumentacija izdelkov - Tehnične risbe za steklenino (ISO 6414:2020)
Standard EN-ISO 6414 vzpostavlja pravila in konvencije za posebno uporabo s tehničnimi risbami na steklenini (npr. laboratorijski steklovini ali steklovini, ki se uporablja na drugih tehničnih področjih). Optični deli v tem standardu niso zajeti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2020
Nadomešča:
SIST EN ISO 6414:1998
Tehnična dokumentacija izdelkov - Tehnične risbe za steklenino (ISO 6414:2020)
Technical product documentation (TPD) - Technical drawings for glassware (ISO
6414:2020)
Technische Produktdokumentation (TPD) - Technische Zeichnungen für Glasgeräte (ISO
6414:2020)
Documentation technique de produits (DTP) - Dessins techniques de verrerie (ISO
6414:2020)
Ta slovenski standard je istoveten z: EN ISO 6414:2020
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
81.040.30 Izdelki iz stekla Glass products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 6414
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2020
EUROPÄISCHE NORM
ICS 01.100.99 Supersedes EN ISO 6414:1994
English Version
Technical product documentation (TPD) - Technical
drawings for glassware (ISO 6414:2020)
Documentation technique de produits (DTP) - Dessins Technische Produktdokumentation (TPD) - Technische
techniques de verrerie (ISO 6414:2020) Zeichnungen für Glasgeräte (ISO 6414:2020)
This European Standard was approved by CEN on 6 January 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6414:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 6414:2020) has been prepared by Technical Committee ISO/TC 10 "Technical
product documentation" in collaboration with Technical Committee CEN/SS F01 “Technical drawings”
the secretariat of which is held by CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2020, and conflicting national standards shall be
withdrawn at the latest by July 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6414:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 6414:2020 has been approved by CEN as EN ISO 6414:2020 without any modification.
INTERNATIONAL ISO
STANDARD 6414
Second edition
2020-01
Technical product documentation
(TPD) — Technical drawings for
glassware
Documentation technique de produits (DTP) — Dessins techniques de
verrerie
Reference number
ISO 6414:2020(E)
©
ISO 2020
ISO 6414:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 6414:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
5 Sections . 2
5.1 Small sections. 2
5.2 The combination of different materials . 3
6 Special glassware indications . 3
6.1 Interchangeable conical ground joint . 3
6.2 Interchangeable spherical ground joint . 3
7 Thin walls . 4
7.1 Drawing of wall thickness . 4
7.2 Indication of diameter . 6
8 Tubes . 7
8.1 Ends of tubes . 7
8.2 Simplified coiled tubes . 7
9 Sintered filters . 8
10 Joints . 9
10.1 General joints . 9
10.2 The specification of adhesive. 9
10.3 General removable parts .10
10.4 Simplified drawing.11
11 Composite glassware .11
Bibliography .13
ISO 6414:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 10, Technical product documentation,
Subcommittee SC 6, Mechanical engineering documentation, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/SS F01, Technical drawings, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 6414:1982), which has been technically
revised.
The main changes to the previous edition are as follows:
— structure updated according to the ISO/IEC Directives, Part 2;
— referenced documents and Bibliography updated;
— addition of transparency in terms of observation and jacketed vessel (see 4.2 and Figure 1);
— surface treatment indication that is not unique to glassware deleted;
— indication of interchangeable conical ground joints updated (see Figure 3);
— indication of interchangeable spherical ground joints and figure added (see 6.2 and Figure 4);
— indication of external and internal diameters for thin walls added;
— diameter indications for thin-walled glassware updated (see Figures 7 to 9);
— Figure 18 b), necessary transition line, added for comparison with Figure 18 a), simplified drawing;
— Figure 17 from the previous edition updated to amend the font size of proportions (see Figure 19).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserve
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.