EN ISO 10893-5:2011
(Main)Non-destructive testing of steel tubes - Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections (ISO 10893-5:2011)
Non-destructive testing of steel tubes - Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections (ISO 10893-5:2011)
ISO 10893-5:2011 specifies requirements for magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections on the tube body and the end/bevel face at the ends.
For the tube body, it specifies requirements for the detection of surface imperfections on all or part of the outside surface of tubes. However, by agreement between the purchaser and manufacturer, it can be applicable to the inside surface over a limited length from the ends of tubes, dependent on the tube diameter.
In addition, ISO 10893-5:2011 can be used, as appropriate, to locate the position of external surface imperfections detected by another non-destructive testing method (e.g. ultrasonic) prior to dressing of the tube surface, and to ensure complete removal of the imperfection after dressing is complete.
For the end/bevel face at the ends of plain-end and beveled-end tubes, ISO 10893-5:2010 specifies requirements for the detection of laminar imperfections which can interfere with subsequent fabrication and inspection operations (e.g. welding and ultrasonic inspection of the welds).
ISO 10893-5:2011 is applicable to the detection of imperfections, other than laminar imperfections, on the end/bevel face. In this case, magnetization is applied in the direction essentially perpendicular to the orientation of the particular imperfections being detected.
It can also be applicable to the testing of hollow sections.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 5: Magnetpulverprüfung nahtloser und geschweißter ferromagnetischer Stahlrohre zum Nachweis von Oberflächenunvollkommenheiten (ISO 10893-5:2011)
Dieser Teil der ISO 10893 legt die Anforderungen an die Magnetpulverprüfung nahtloser und geschweißter ferromagnetischer Rohre zum Nachweis von Oberflächenunvollkommenheiten am Rohrkörper und an den Stirnflächen/Stirnflächenanschrägungen der Rohrenden fest. Für den Rohrkörper werden Anforderungen zum Nachweis von Oberflächenunvollkommenheiten auf der gesamten oder in Teilbereichen der Rohraußenoberfläche festgelegt. Nach Vereinbarung zwischen Besteller und Hersteller kann es auch auf die Prüfung der Innenoberfläche, in Abhängigkeit vom Rohrdurchmesser über eine begrenzte Länge von den Rohrenden aus, angewendet werden. Zusätzlich darf dieser Teil der ISO 10893, soweit zweckmäßig, zur Lokalisierung der Lage äußerer Oberflächenunvollkommenheiten, die durch andere zerstörungsfreie Prüfverfahren nachgewiesen wurden (z. B. durch Ultraschallprüfung), vor der Nachbearbeitung und zur Sicherstellung der vollständigen Entfernung der Unvollkommenheiten angewendet werden. Für die Stirnflächen/Stirnflächenanschrägungen von Rohren mit glatten oder angeschrägten Enden legt dieser Teil der ISO 10893 Anforderungen zum Nachweis von Dopplungen fest, die die nachfolgende Rohrfertigung und -prüfung (z. B. Schweißen, Ultraschallprüfung der Schweißstöße usw.) beeinträchtigen können. Dieser Teil der ISO 10893 darf auch für den Nachweis von anderen Unvollkommenheiten als Dopplungen an den Stirnflächen bzw. Stirnflächenanschrägungen angewendet werden. In diesem Fall muss im Wesentlichen senkrecht zur Hauptorientierung der nachzuweisenden Unvollkommenheiten magnetisiert werden. Dieses Dokument kann auch für die Prüfung von Hohlprofilen angewendet werden.
Essais non destructifs des tubes en acier - Partie 5: Contrôle par magnétoscopie des tubes en acier ferromagnétique sans soudure et soudés pour la détection des imperfections de surface (ISO 10893-5:2011)
L'ISO 10893-5:2011 spécifie les exigences relatives au contrôle par magnétoscopie des tubes en acier ferromagnétique sans soudure et soudés pour la détection des imperfections de surface sur le corps du tube et sur les faces d'extrémité ou les chanfreins aux extrémités.
Pour le corps du tube, elle spécifie les exigences relatives à la détection des imperfections de surface sur tout ou partie de la surface extérieure des tubes. Cependant, par accord entre l'acheteur et le producteur, elle est applicable à la surface intérieure sur une longueur limitée à partir des extrémités des tubes, selon le diamètre du tube.
En outre, l'ISO 10893-5:2011 peut être utilisée, le cas échéant, pour déterminer l'emplacement d'imperfections sur la surface extérieure détectées par une autre méthode de contrôle non destructif (par exemple par ultrasons), avant réparation de la surface des tubes et pour garantir l'élimination complète de l'imperfection après réparation.
Pour les faces d'extrémité ou les chanfreins aux extrémités des tubes à extrémités lisses ou chanfreinées, l'ISO 10893-5:2011 spécifie les exigences relatives à la détection des dédoublures pouvant avoir une incidence sur les opérations de fabrication et de contrôle ultérieures (par exemple soudage ou contrôle par ultrasons des soudures).
L'ISO 10893-5:2011 est aussi applicable à la détection des imperfections autres que des dédoublures sur les faces d'extrémité ou les chanfreins. Dans ce cas, la magnétisation est à appliquer essentiellement perpendiculairement à l'orientation des imperfections particulières à détecter.
Elle est également applicable au contrôle des profils creux.
Neporušitveno preskušanje jeklenih cevi - 5. del: Ugotavljanje površinskih napak nevarjenih in varjenih feromagnetnih jeklenih cevi z magnetnimi delci (ISO 10893-5:2011)
Ta del ISO 10893 določa zahteve za ugotavljanje površinskih napak nevarjenih in varjenih feromagnetnih jeklenih cevi na telesu cevi in koncih/poševninah na koncih z magnetnimi delci. Za telo cevi določa zahteve za odkrivanje površinskih napak na celotni zunanji površini cevi ali njenem delu. Po dogovoru med kupcem in proizvajalcem lahko velja tudi za omejeno dolžino notranje površine od koncev cevi, odvisno od premera cevi. Poleg tega se ta del ISO 10893 lahko uporablja, kot je ustrezno, za iskanje mest napak na zunanji površini, odkritih z drugo neporušitveno preskusno metodo (npr. ultrazvočno) pred apretiranjem površine cevi, in za zagotavljanje popolne odstranitve napak po zaključku apretiranja. Za konce/poševnine na koncih ravnih in poševnih cevi ta del ISO 10893 določa zahteve za odkrivanje laminarnih napak, ki lahko motijo nadaljnje operacije izdelave in pregleda (npr. varjenje in ultrazvočni pregled varov). Ta del ISO 10893 velja za odkrivanje napak, razen laminarnih napak, na koncu/poševnini. V tem primeru se magnetizacija uporabi v smeri, pretežno pravokotni na smer konkretnih napak, ki se odkrivajo. Lahko velja tudi za preskušanje votlih delov.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
1DGRPHãþD
SIST EN 10246-12:2000
SIST EN 10246-18:2000
Neporušitveno preskušanje jeklenih cevi - 5. del: Ugotavljanje površinskih napak
nevarjenih in varjenih feromagnetnih jeklenih cevi z magnetnimi delci (ISO 10893-
5:2011)
Non-destructive testing of steel tubes - Part 5: Magnetic particle inspection of seamless
and welded ferromagnetic steel tubes for the detection of surface imperfections (ISO
10893-5:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 5: Magnetpulverprüfung nahtloser und
geschweißter ferromagnetischer Stahlrohre zum Nachweis von
Oberflächenunregelmäßigkeiten (ISO 10893-5:2011)
Essais non destructifs des tubes en acier - Partie 5: Contrôle par magnétoscopie des
tubes en acier ferromagnétiques sans soudure ou soudés pour la détection des
imperfections de surface (ISO 10893-5:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-5:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10893-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-12:2000, EN 10246-18:2000
English Version
Non-destructive testing of steel tubes - Part 5: Magnetic particle
inspection of seamless and welded ferromagnetic steel tubes for
the detection of surface imperfections (ISO 10893-5:2011)
Essais non destructifs des tubes en acier - Partie 5: Zerstörungsfreie Prüfung von Stahlrohren - Teil 5:
Contrôle par magnétoscopie des tubes en acier Magnetpulverprüfung nahtloser und geschweißter
ferromagnétique sans soudure et soudés pour la détection ferromagnetischer Stahlrohre zum Nachweis von
des imperfections de surface (ISO 10893-5:2011) Oberflächenunvollkommenheiten (ISO 10893-5:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-5:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 10893-5:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-12:2000, EN 10246-18:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10893-5:2011 has been approved by CEN as a EN ISO 10893-5:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 10893-5
First edition
2011-04-01
Non-destructive testing of steel tubes —
Part 5:
Magnetic particle inspection of seamless
and welded ferromagnetic steel tubes for
the detection of surface imperfections
Essais non destructifs des tubes en acier —
Partie 5: Contrôle par magnétoscopie des tubes en acier
ferromagnétique sans soudure et soudés pour la détection des
imperfections de surface
Reference number
ISO 10893-5:2011(E)
©
ISO 2011
ISO 10893-5:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 10893-5:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 General requirements .2
5 Test method .3
5.1 General .3
5.2 Testing the tube body .3
5.3 Testing the end/bevel face.4
6 Evaluation of indications.4
6.1 General .4
6.2 Special requirements for evaluation of indications in the pipe body .5
7 Acceptance .7
7.1 Tube body .7
7.2 End/bevel face .7
8 Test report.7
ISO 10893-5:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10893-5 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 19, Technical
delivery conditions for steel tubes for pressure purposes.
This first edition cancels and replaces ISO 13664:1997 and ISO 13665:1997, which have been technically
revised.
ISO 10893 consists of the following parts, under the general title Non-destructive testing of steel tubes:
⎯ Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel
tubes for the verification of hydraulic leaktightness
⎯ Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel
tubes for the detection of imperfections
⎯ Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-
welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections
⎯ Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface
imperfections
⎯ Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of
surface imperfections
⎯ Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections
⎯ Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of
imperfections
⎯ Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar
imperfections
⎯ Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the
manufacture of welded steel tubes
⎯ Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged
arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections
iv © ISO 2011 – All rights reserved
ISO 10893-5:2011(E)
⎯ Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of
longitudinal and/or transverse imperfections
⎯ Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except
submerged arc-welded) steel tubes
INTERNATIONAL STANDARD ISO 10893-5:2011(E)
Non-destructive testing of steel tubes —
Part 5:
Magnetic particle inspection of seamless and welded
ferromagnetic steel tubes for the detection of surface
imperfections
1 Scope
This part of ISO 10893 specifies requirements for magnetic particle inspection of seamless and welded
ferromagnetic steel tubes for the detection of surface imperfections on the tube body and the end/bevel face
at the ends.
For the tube body, it specifies requirements for the detection of surface imperfections on all or part of the
outside surface of tubes. However, by agreement between the purchaser and manufacturer, it can be
applicable to the inside surface over a limited length from the ends of tubes, dependent on the tube diameter.
In addition, this part of ISO 10893 can be used, as appropriate, to locate the position of external surface
imperfections detected by anothe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.