FprCEN/TS 18116
(Main)Thermoplastics pipes and fittings - Design for recycling guidelines
Thermoplastics pipes and fittings - Design for recycling guidelines
This document specifies design for recycling guidelines for thermoplastics pipes and fittings, used as construction products or used for water supply to irrigation systems.
NOTE 1 Components used in irrigation systems such as flexibles and drip lines are not part of this document.
NOTE 2 Pipes and fittings used for cable management are not part of this document.
NOTE 3 Packaging of pipes and fittings is not part of this document.
The guidelines in this document are developed to facilitate mechanical recycling.
NOTE 4 The guidelines could also be beneficial for chemical recycling.
Thermoplastics pipes and fittings are considered to be those, where the total volume of the thermoplastic compound/formulation exceeds 50 %.
This document can also be used for other thermoplastics products used in a piping system such as manholes, inspection chambers, infiltration boxes and valves.
Rohre und Formstücke aus Thermoplasten - Leitlinien für die recyclingorientierte Gestaltung
Dieses Dokument legt Leitlinien für die recyclingorientierte Gestaltung von thermoplastischen Rohren und Formstücken fest, die als Bauprodukte oder zur Wasserversorgung in Bewässerungsanlagen verwendet werden.
ANMERKUNG 1 Die in Bewässerungsanlagen verwendeten Bauteile wie biegsame Leitungen und Tropfleitungen sind nicht Bestandteile dieses Dokuments.
ANMERKUNG 2 Rohre und Formstücke, die für die Kabelführung verwendet werden, sind nicht Bestandteile dieses Dokuments.
ANMERKUNG 3 Die Verpackung von Rohren und Formstücken ist nicht Bestandteil dieses Dokuments.
Die Leitlinien dieses Dokuments wurden erstellt, um mechanisches Recycling zu erleichtern.
ANMERKUNG 4 Die Leitlinien könnten auch für das chemische Recycling von Nutzen sein.
Als thermoplastische Rohre und Formstücke gelten solche, bei denen das Gesamtvolumen der Thermoplastformmasse/ formulierung mehr als 50 % beträgt.
Dieses Dokument kann auch für andere thermoplastische Produkte, die in einem Rohrleitungssystem zum Einsatz kommen, angewendet werden, wie z. B. für Mannlöcher, Revisionsschächte, Sickerkästen und Armaturen.
Tubes et raccords en matières thermoplastiques - Directives de conception pour le recyclage
Le présent document spécifie les lignes directrices pour le recyclage des tubes et raccords en matières thermoplastiques, utilisés comme produits de construction ou utilisés pour l'alimentation en eau des systèmes d'irrigation.
NOTE 1 Les composants utilisés dans les systèmes d'irrigation, tels que les tuyaux flexibles et les lignes d’égouttement, ne font pas partie du présent document.
NOTE 2 Les tubes et raccords utilisés pour la gestion des câbles ne font pas partie du présent document.
NOTE 3 L'emballage des tubes et raccords ne fait pas partie du présent document.
Les lignes directrices du présent document ont été élaborées pour faciliter le recyclage mécanique.
NOTE 4 Les lignes directrices pourraient également être utiles pour le recyclage chimique.
Les tubes et raccords en matières thermoplastiques sont considérés comme étant ceux dont le volume total de la composition/formulation en thermoplastique est supérieur à 50 %.
Le présent document peut également être utilisé pour d'autres produits en thermoplastiques utilisés dans un système de canalisations, tels que les regards, les boîtes d'inspection et de branchement, les structures d'infiltration et les robinets.
Plastomerne cevi in fitingi - Smernice za načrtovanje za recikliranje
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Plastomerne cevi in fitingi - Smernice za načrtovanje za recikliranje
Thermoplastics pipes and fittings - Design for recycling guidelines
Rohre und Formstücke aus Thermoplasten - Leitlinien für die recyclingorientierte
Gestaltung
Tubes et raccords en matières thermoplastiques - Directives de conception pour le
recyclage
Ta slovenski standard je istoveten z: FprCEN/TS 18116
ICS:
13.030.50 Recikliranje Recycling
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
FINAL DRAFT
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
August 2024
ICS 13.030.50; 23.040.20; 23.040.45
English Version
Thermoplastics pipes and fittings - Design for recycling
guidelines
Tubes et raccords en matières thermoplastiques - Rohre und Formstücke aus Thermoplasten - Leitlinien
Directives de conception pour le recyclage für die recyclingorientierte Gestaltung
This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 155.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 18116:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Design considerations . 6
4.1 Material selection . 6
4.2 Hazardous substances . 7
4.3 Marking . 7
4.4 Documentation . 8
Bibliography . 9
European foreword
This document (FprCEN/TS 18116:2024) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the Vote on TS.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Introduction
This document is developed in response to the standardization request M/584 of 1st August 2022.
The scope of this document, requested by M/584, is extended from “HDPE pipes and fittings and PVC
pipes and fittings” to “thermoplastics pipes and fittings”.
The product and material requirements (virgin and/or recyclate) as defined in product standards should
be fulfilled, as applicable.
NOTE Recommendations to the value chain of thermoplastics piping systems to stimulate the use of
thermoplastics recyclates can be found in the EN 14541 series. In CEN/TS 14541-2, guidance and information is
given for drafting product standards for defining relevant characteristics, e.g. for fingerprinting.
1 Scope
This document specifies design for recycling guidelines for thermoplastics pipes and fittings, used as
construction products or used for water supply to irrigation systems.
NOTE 1 Components used in irrigation systems such as flexibles and drip lines are not part of this document.
NOTE 2 Pipes and fittings used for cable management are not part of this document.
NOTE 3 Packaging of pipes and fittings is not part of this document.
The guidelines in this document are developed to facilitate mechanical recycling.
NOTE 4 The guidelines could also be beneficial for chemical recycling.
Thermoplastics pipes and fittings are considered to be those, where the total volume of the thermoplastic
compound/formulation exceeds 50 %.
This document can also be used for other thermoplastics products used in a piping system such as
manholes, inspection chambers, infiltration boxes and valves.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 14021:2016, Environmental labels and declarations – Self declared environmental claims (Type II
environmental labelling (ISO 14021:2016)
EN 14541-1, Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: vocabulary
3 Terms and definitions
For the purposes of this document the terms and definitions given in EN 14541-1 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp/
3.1
construction product
any product or kit that is produced and placed on the market for permanent incorporation in construction
works with respect to the basic requirements for w
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.