prEN IEC 61116:2024
(Main)Electromechanical equipment guidance for small hydroelectric installations
Electromechanical equipment guidance for small hydroelectric installations
IEC 61116:2025 used as a guidance that applies to hydroelectric installations containing impulse or reaction turbines with unit power up to about 15 MW and reference diameter of about 3 m. These figures do not represent absolute limits. This document deals only with the direct relations between the purchaser or the consulting engineer and the supplier. It does not deal with civil works, administrative conditions or commercial conditions. This document is intended to be used by all concerned in the installation of electromechanical equipment for small hydroelectric plants. This document, based essentially on practical information, aims specifically at supplying the purchaser of the equipment with information which will assist him with the following: preparation of the call for tenders; - evaluation of the tenders; - contact with the supplier during the design and manufacture of the equipment; - quality control during the manufacture and shop-testing; - follow-up of site erection; - commissioning; - acceptance tests; - operation and maintenance. The document comprises the following: a) general requirements for the electromechanical equipment of small hydroelectric installations; b) technical specifications for the electromechanical equipment, excluding its dimensioning and standardization; c) requirements for acceptance, operation and maintenance This second edition cancels and replaces the first edition published in 1992. This edition includes the following significant technical changes with respect to the previous edition: a) harmonization of scope with IEC 62006; b) introduction of new technical aspects; c) overall editorial revision.
Anleitung für die elektromechanische Ausrüstung von kleinen Wasserkraftanlagen
Recommandations pour l'équipement électromécanique des petits aménagements hydroélectriques
L'IEC 61116:2025 fournit des recommandations applicables aux aménagements hydroélectriques équipés de turbines à action ou à réaction caractérisées par une puissance jusqu'à 15 MW environ par groupe et par un diamètre de référence de 3 m environ. Ces valeurs ne constituent pas des limites absolues. Le présent document traite uniquement des relations directes entre l'acquéreur ou l'ingénieur conseil et le fournisseur. II ne traite ni du génie civil ni des conditions administratives ou commerciales. Le présent document est destiné à être utilisé par l'ensemble des parties intéressées par l'installation d'équipements électromécaniques pour les petits aménagements hydroélectriques. Le présent document, fondé essentiellement sur des informations pratiques, a pour objet particulier de fournir à l'acquéreur de l'équipement des renseignements qui lui faciliteront: - la préparation des appels d'offres; - l'évaluation des offres; - les contacts avec le fournisseur pendant la conception et la fabrication des équipements; - le contrôle de qualité pendant la fabrication et les essais en usine; - le suivi du montage sur site; - la mise en service; - les essais de réception; - l'exploitation et l'entretien. Le document comporte: a) des exigences générales pour l'équipement électromécanique des petits aménagements hydroélectriques; b) des spécifications techniques pour l'équipement électromécanique, à l'exclusion de son dimensionnement et de toute normalisation dans ce domaine; c) des exigences pour la réception, l'exploitation et l'entretien Cette deuxième édition annule et remplace la première édition parue en 1992. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) harmonisation du domaine d'application avec l'IEC 62006; b) introduction de nouveaux aspects techniques; c) révision rédactionnelle complète
Vodilo za elektromehansko opremo malih hidroelektrarn
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Vodilo za elektromehansko opremo malih hidroelektrarn
Electromechanical equipment guide for small hydroelectric installations
Anleitung für die elektromechanische Ausrüstung von kleinen Wasserkraftanlagen
Guide pour l'équipement électromécanique des petits aménagements hydro-électriques
Ta slovenski standard je istoveten z: prEN IEC 61116:2024
ICS:
27.140 Vodna energija Hydraulic energy engineering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
4/510/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61116 ED2
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2024-09-27 2024-12-20
SUPERSEDES DOCUMENTS:
4/492/CD, 4/501A/CC
IEC TC 4 : HYDRAULIC TURBINES
SECRETARIAT: SECRETARY:
Canada Mrs Christine Geraghty
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Electromechanical equipment guide for small hydroelectric installations
PROPOSED STABILITY DATE: 2026
NOTE FROM TC/SC OFFICERS:
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it,
for any other purpose without permission in writing from IEC.
IEC CDV 61116 © IEC 2024 2 4/510/CDV
1 CONTENTS
2 FOREWORD . 4
3 1 Scope . 6
4 2 Normative references. 6
5 3 Terms, definitions, symbols and units . 7
6 3.1 General . 7
7 3.2 General terminology . 7
8 3.3 Units . 9
9 4 Methodology . 10
10 5 Description of installation and operating conditions of power station . 12
11 5.1 Site conditions . 12
12 5.2 Hydraulic conditions for plant and design criteria for the units . 17
13 5.3 Electrical conditions for plant operation . 19
14 5.3.1 The plant is intended to operate in an isolated grid . 19
15 5.3.2 The plant is intended to operate in parallel with a grid which imposes
16 the frequency . 20
17 5.3.3 Energy transport and distribution . 20
18 5.4 Types of regulation and modes of operation . 20
19 5.4.1 Frequency regulation . 20
20 5.4.2 Power regulation . 21
21 5.4.3 Level control . 21
22 5.4.4 Flow regulation . 21
23 5.4.5 Simplified governing . 21
24 5.5 Automation, telemetry, remote control, alarms . 21
25 6 Equipment specifications . 21
26 6.1 Technical requirements . 21
27 6.2 Limits of the supply . 22
28 6.2.1 For the hydraulic system . 22
29 6.2.2 For the electric system . 22
30 6.2.3 For the auxiliary equipment system . 22
31 6.2.4 Elements not normally included in the supply . 22
32 6.3 Specifications of the elements of the plant . 22
33 6.3.1 Trashrack and rack cleaner . 22
34 6.3.2 Water-level control . 22
35 6.3.3 Discharge closure devices (see Figure 5) . 23
36 6.3.4 Penstock . 25
37 6.3.5 Turbine (see Figure 6) . 25
38 6.3.6 Generator . 29
39 6.3.7 Automatic control system . 31
40 6.3.8 Main transformers (reference can be made to IEC 60076) . 34
41 6.3.9 Auxiliary equipment . 35
42 6.3.10 Spare parts and special tools . 36
43 6.3.11 Mechanical handling . 36
44 6.3.12 Corrosion protection . 37
45 6.4 Guarantees . 37
46 6.4.1 General . 37
47 6.4.2 Discharge closure devices . 38
48 6.4.3 Turbine . 38
49 6.4.4 Generator . 38
50 6.4.5 Governor . 38
IEC CDV 61116 © IEC 2024 3 4/510/CDV
51 6.4.6 Speed increaser. 39
52 6.4.7 Excitation equipment . 39
53 6.4.8 Comments concerning the complete generating set . 39
54 6.4.9 Main transformer . 39
55 6.5 General conditions for tender enquiries and comparison of tenders . 40
56 6.5.1 Instructions to tenderers . 40
57 6.5.2 General conditions of contract . 40
58 6.5.3 Technical comparison of tenders . 40
59 7 Inspection, delivery, operation and maintenance . 42
60 7.1 Approval of the design and inspection of the work . 42
61 7.1.1 Approval of design documents . 42
62 7.1.2 Inspection of materials and sub-assemblies . 42
63 7.1.3 Inspection at manufacturer's works . 43
64 7.1.4 Delivery . 43
65 7.1.5 Assembly at site . 43
66 7.2 Commissioning. 44
67 7.2.1 Preliminary checks before watering-up . 44
68 7.2.2 Watering-up . 44
69 7.2.3 Unit rotation . 45
70 7.2.4 Preliminary checks and electrical load tests . 45
71 7.3 Operation . 46
72 7.3.1 Probationary period . 46
73 7.3.2 Guarantee period . 46
74 7.3.3 Normal operation . 48
75 7.4 Training of personnel . 48
76 7.5 Checking and maintenance . 48
77 Bibliography . 51
79 Figure 1 – Example of sequence of events . 11
80 Figure 2 – Power station arrangements . 15
81 Figure 3 – Run-of-river power station arrangements . 17
82 Figure 4 – Flow duration curve (showing river flow and plant flow) . 18
83 Figure 5 – Hydraulic closure devices (examples) . 24
84 Figure 6 – Schematic representation of a hydraulic machine . 26
85 Figure 7 – Electrical single-line diagram . 34
87 Table 1 – Energy utilization for passive and active loads . 20
88 Table 2 - Elements of bid evaluation . 41
89 Table 3 - Examples of checks during normal operation . 50
IEC CDV 61116 © IEC 2024 4 4/510/CDV
91 INTERNATIONAL ELECTROTECHNICAL COMMISSION
92 ____________
94 ELECTROMECHANICAL EQUIPMENT GUIDANCE FOR
95 SMALL HYDROELECTRIC INSTALLATIONS
97 FOREWORD
98 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
99 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
100 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
101 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
102 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
103 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
104 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
105 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
106 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
107 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
108 consensus of opinion on the relevant subjects since each technical committee has representation from all
109 interested IEC National Committees.
110 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
111 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
112 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
113 misinterpretation by any end user.
114 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
115 transparently to the maximum extent possible in their national and regional publications. Any divergence between
116 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
117 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
118 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
119 services carried out by independent certification bodies.
120 6) All users should ensure that they have the latest edition of this publication.
121 7) No liability shall attach to IEC or its directors, employees, servants or agents includi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.