Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements

This part of IEC 62196 is applicable to EV plugs, EV socket-outlets, vehicle connectors, vehicle inlets, herein referred to as "accessories", and to cable assemblies for electric vehicles (EV) intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding: - 690 V AC 50 Hz to 60 Hz, at a rated current not exceeding 250 A; - 1 500 V DC at a rated current not exceeding 800 A. These accessories and cable assemblies are intended to be installed by instructed persons (IEV 195-04-02) or skilled persons (IEV 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851 (all parts), which operate at different voltages and frequencies, and which can include extra-low voltage and communication signals. These accessories and cable assemblies are intended to be used at an ambient temperature between −30 °C and +40 °C. NOTE 1 In some countries, other requirements can apply. NOTE 2 In the following country, −35 °C applies: SE. NOTE 3 The manufacturer can enlarge the temperature range on the condition that the specified range information is provided. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this document are intended for use in electric vehicle supply equipment in accordance with IEC 61851 (all parts). This document does not apply to standard plug and socket-outlets used for mode 1 and mode 2 according to IEC 61851-1:2017, 6.2. NOTE 4 In the following countries, mode 1 is not allowed: UK, US, CA, SG.

Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden von Elektrofahrzeugen – Teil 1: Allgemeine Anforderungen

Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs de véhicule - Charge conductive des véhicules électriques - Partie 1: Exigences générales

L’IEC 62196-1:2022 s’applique aux fiches VE, socles de prise de courant VE, prises mobiles de véhicule, socles de connecteur de véhicules, ci-après désignés par le terme "appareils", et aux câbles de charge pour véhicules électriques (VE) destinés à être utilisés dans les systèmes de charge conductive qui comprennent des moyens de contrôle, avec une tension assignée d’emploi n’excédant pas:  
690 V 50 Hz à 60 Hz, à un courant alternatif assigné n’excédant pas 250 A;
1 500 V, à un courant continu assigné n’excédant pas 800 A.  Cette quatrième édition annule et remplace la troisième édition parue en 2014. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
suppression des références aux interfaces universelles en courant alternatif et en courant continu;
exigences supplémentaires pour les matériaux de contact et la métallisation;
modification de l’essai d’échauffement pour inclure des points de mesure supplémentaires;
essais supplémentaires pour examiner les contraintes et la stabilité thermique, l’usure mécanique et une mauvaise utilisation des appareils, ainsi que leur exposition à des contaminants;
déplacement des informations et exigences concernant la charge en courant continu dans l’IEC 62196-3.  La version française de la norme n’a pas été soumise au vote.

Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih vozil - 1. del: Splošne zahteve (IEC 62196-1:2022)

Ta del standarda IEC 62196 se uporablja za vtiče, vtičnice, konektorje, uvodnice (v nadaljnjem besedilu: »priključki«) in kabelske sestave na električnih vozilih, ki so namenjeni sistemom kabelskega napajanja, ki vključujejo krmilno sredstvo z nazivno obratovalno napetostjo, ki ne presega napetosti:
– 690 V za izmenični tok, 50–60 Hz, pri nazivnem toku, ki ne presega 250 A,
– 1500 V za enosmerni tok pri nazivnem toku, ki ne presega 800 A.
Te priključke in kabelske sestave lahko namestijo le poučene osebe, (IEV 195-04-02) ali usposobljene osebe (IEV 195-04-01).
Ti priključki in kabelski sestavi so namenjeni za uporabo pri tokokrogih, navedenih v standardu IEC 61851 (vsi deli), ki delujejo pri različnih napetostih in frekvencah ter lahko vključujejo malo napetost in komunikacijske signale.
Ti priključki in kabelski sestavi so namenjeni za uporabo pri temperaturi okolja, in sicer med –30 °C in +40 °C.
OPOMBA 1: V nekaterih državah lahko veljajo drugačne zahteve.
OPOMBA 2: V naslednji državi velja –35 °C: SE.
OPOMBA 3: Proizvajalec lahko poveča temperaturno območje pod pogojem, da so zagotovljene informacije o posebnem območju.
Ti priključki se lahko priključijo samo na kable z vodniki iz bakra ali bakrove zlitine.
Priključki, zajeti v tem dokumentu, so namenjeni uporabi v napajalni opremi za električna vozila v skladu s standardom IEC 61851 (vsi deli).
Ta dokument se ne uporablja za standardne vtiče in vtičnice za način 1 ali način 2 v skladu s točko 6.2 standarda IEC 61851-1:2017.
OPOMBA 4: Način 1 ni dovoljen v naslednjih državah: ZK, ZDA, CA, SG.

General Information

Status
Published
Publication Date
17-Nov-2022
Current Stage
6060 - Document made available - Publishing
Start Date
18-Nov-2022
Completion Date
18-Nov-2022

Relations

Buy Standard

Standard
EN IEC 62196-1:2023 - BARVE
English language
101 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN IEC 62196-1:2020 - BARVE
English language
93 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 62196-1:2023
01-maj-2023
Nadomešča:
SIST EN 62196-1:2015
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih
vozil - 1. del: Splošne zahteve (IEC 62196-1:2022)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of
electric vehicles - Part 1: General requirements (IEC 62196-1:2022)
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden
von Elektrofahrzeugen - Teil 1: Allgemeine Anforderungen (IEC 62196-1:2022)
Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs
de véhicule - Charge conductive des véhicules électriques - Partie 1: Exigences
générales (IEC 62196-1:2022)
Ta slovenski standard je istoveten z: EN IEC 62196-1:2022
ICS:
29.120.30 Vtiči, vtičnice, spojke Plugs, socket-outlets,
couplers
43.120 Električna cestna vozila Electric road vehicles
SIST EN IEC 62196-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62196-1:2023

---------------------- Page: 2 ----------------------
SIST EN IEC 62196-1:2023


EUROPEAN STANDARD EN IEC 62196-1

NORME EUROPÉENNE

EUROPÄISCHE NORM November 2022
ICS 29.120.30; 43.120 Supersedes EN 62196-1:2014
English Version
Plugs, socket-outlets, vehicle connectors and vehicle inlets -
Conductive charging of electric vehicles - Part 1: General
requirements
(IEC 62196-1:2022)
Fiches, socles de prise de courant, prises mobiles de Stecker, Steckdosen, Fahrzeugkupplungen und
véhicule et socles de connecteurs de véhicule - Charge Fahrzeugstecker - Konduktives Laden von
conductive des véhicules électriques - Partie 1: Exigences Elektrofahrzeugen - Teil 1: Allgemeine Anforderungen
générales (IEC 62196-1:2022)
(IEC 62196-1:2022)
This European Standard was approved by CENELEC on 2022-11-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62196-1:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62196-1:2023
EN IEC 62196-1:2022 (E)
European foreword
The text of document 23H/499/FDIS, future edition 4 of IEC 62196-1, prepared by SC 23H "Plugs,
Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles" of
IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 62196-1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-08-09
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-11-09
document have to be withdrawn
This document supersedes EN 62196-1:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62196-1:2022 was approved by CENELEC as a European
Standard without any modificati
...

SLOVENSKI STANDARD
oSIST prEN IEC 62196-1:2020
01-marec-2020
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih
vozil - 1. del: Splošne zahteve
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of
electric vehicles - Part 1: General requirements
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden
von Elektrofahrzeugen – Teil 1: Allgemeine Anforderungen
Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteur
de véhicule - Charge conductive des véhicules électriques - Partie 1: Règles générales
Ta slovenski standard je istoveten z: prEN IEC 62196-1:2020
ICS:
29.120.30 Vtiči, vtičnice, spojke Plugs, socket-outlets,
couplers
43.120 Električna cestna vozila Electric road vehicles
oSIST prEN IEC 62196-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 62196-1:2020

---------------------- Page: 2 ----------------------
oSIST prEN IEC 62196-1:2020
23H/461/CDV

COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62196-1 ED4
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2020-01-10 2020-04-03
SUPERSEDES DOCUMENTS:
23H/444/CD,23H/449A/CC

IEC SC 23H : PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL AND SIMILAR APPLICATIONS, AND FOR ELECTRIC
VEHICLES
SECRETARIAT: SECRETARY:
France Mr Bertrand Doignon
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:

TC 69
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY

SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.

TITLE:
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric
vehicles - Part 1: General requirements

PROPOSED STABILITY DATE: 2025

NOTE FROM TC/SC OFFICERS:
If necessary, comments will be reviewed in an MT 8 meeting in April 2020

Copyright © 2019 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing
National Committee positions. You may not copy or "mirror" the file or printed version of the document, or any
part of it, for any other purpose without permission in writing from IEC.

---------------------- Page: 3 ----------------------
oSIST prEN IEC 62196-1:2020
62196-1/Ed.4/CDV © IEC(E) 2 23H/461/CDV
1 CONTENTS
2
3 FOREWORD . 6
4 INTRODUCTION . 8
5 1 Scope . 9
6 2 Normative references . 9
7 3 Terms and definitions . 11
8 4 General . 19
9 4.1 General requirements . 19
10 4.2 Components. 19
11 4.3 General notes on tests . 20
12 5 Ratings . 21
13 5.1 Preferred rated operating voltage ranges . 21
14 5.2 Preferred rated currents . 21
15 6 Connection between the power supply and the electric vehicle . 22
16 6.1 Interfaces .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.