HD 477.3 S1:1988
(Main)Methods of measurement for equipment used in terrestrial radio-relay systems - Part 3: Simulated systems
- BACK
- 09-Oct-1988
- 30-Sep-1989
- 33.060.30
- CLC/SR 102
Methods of measurement for equipment used in terrestrial radio-relay systems - Part 3: Simulated systems
Gives certain definitions and some general observations on simulated systems.
Meßverfahren für Geräte in terrestrischen Richtfunksystemen - Teil 3: Simulierte Systeme
Méthodes de mesure applicables au matériel utilisé dans les faisceaux hertziens terrestres - Partie 3: Liaisons simulées
Contient certaines définitions et observations générales concernant les liaisons simulées.
Methods of measurement for equipment used in terrestrial radio-relay systems - Part 3: Simulated systems
General Information
Standards Content (Sample)
SLOVENSKI SIST HD 477.3 S1:2002
prva izdaja
STANDARD
oktober 2002
Methods of measurement for equipment used in terrestrial radio-relay systems -
Part 3: Simulated systems
ICS 33.060.30 Referenčna številka
SIST HD 477
...
This May Also Interest You
IEC 60728-1-1:2014 is applicable to RF cabling for two-way home networks with wired cords or wireless links inside a room and primarily intended for television and sound signals operating between about 5 MHz and 3 000 MHz. The frequency range is extended to 6 000 MHz for distribution techniques that replace wired cords with a wireless two-way communication. This second edition cancels and replaces the first edition published in 2010, and constitutes a technical revision. It includes the following changes: update of performance requirements in Clause 5 to include those for DVB-T2 signals.
- Standard65 pagesEnglish languagesale 10% offe-Library read for×1 day
- 28-Aug-2014
- 33.060.30
- 33.160.01
- CEN/CLC/WS 016
This European Standard describes: – the system physical structure; – the system control signals, which implement an extension of the DiSEqC set of commands described in the DiSEqC bus functional specification; – the definition of identified configurations; – management of the potential collisions in the control signals traffic.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Oct-2007
- 28-Feb-2010
- 33.060.30
- 33.160.01
- CLC/TC 209
This standard applies for the interaction channel for interactive television networks using Geostationary Satellites with fixed return channel satellite terminals via low data rate dedicated return link. It specifies the essential elements for the implementation of the interaction channel.
- Standard114 pagesEnglish languagesale 10% offe-Library read for×1 day
- 20-Feb-2007
- 33.060.30
- 33.170
- CLC/TC 100X
Initially handled by TC 206 (disbanded) * D141/C101: Transferred to new TC 100X
2021: CLC legacy converted by DCLab NISOSTS
- Amendment18 pagesEnglish languagesale 10% offe-Library read for×1 day
- 27-Apr-1999
- 30-Sep-1999
- 31.220.10
- 33.060.30
- 33.160.20
- CLC/TC 100X
Deals with the standardization of interconnections and matching values for satellite receivers for individual television and sound radio broadcast reception in the 10,70 GHz to 12,75 GHz band.
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Jan-1996
- 31-Aug-1996
- 31.220.10
- 33.060.30
- 33.160.20
- CLC/TC 100X
IEC 60730-2-6:2025 applies to automatic electrical pressure sensing controls • for use in, on, or in association with equipment for household appliance and similar use; NOTE 1 Throughout this document, the word "equipment" means "appliance and equipment" and "controls" means "pressure sensing controls". • for building automation within the scope of ISO 16484 series and IEC 63044 series (HBES/BACS); EXAMPLE 1 Independently mounted automatic electrical pressure sensing controls, controls in smart grid systems and controls for building automation systems within the scope of ISO 16484-2. • for equipment that is used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications; EXAMPLE 2 Automatic electrical pressure sensing controls for commercial catering, heating and air-conditioning equipment. • that are smart enabled automatic electrical pressure sensing controls; EXAMPLE 3 Smart grid automatic electrical pressure sensing controls, remote interfaces/control of energy-consuming equipment including computer or smart phone. • that are AC or DC powered controls with a rated voltage not exceeding 690 V AC or 600 V DC; • used in, on, or in association with equipment that use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof; • utilized as part of a control system or controls which are mechanically integral with multifunctional controls having non-electrical outputs; • using NTC or PTC thermistors and to discrete thermistors, requirements for which are contained in Annex J; • that are mechanically or electrically operated, responsive to or controlling a pressure or vacuum; • as well as manual controls when such are electrically and/or mechanically integral with automatic controls. NOTE 2 Requirements for manually actuated mechanical switches not forming part of an automatic control are contained in IEC 61058-1-1. This document is also applicable to individual pressure sensing controls utilized as part of a control system or pressure sensing controls which are mechanically integral with multi-functional controls having non-electrical outputs. This document is also applicable to pressure sensing controls for appliances within the scope of IEC 60335-1. This document applies to - the inherent safety of pressure sensing controls, and - functional safety of pressure sensing controls and safety related systems, - pressure sensing controls where the performance (for example the effect of EMC phenomena) of the product can impair the overall safety and performance of the controlled system, - the operating values, operating times, and operating sequences where such are associated with equipment safety. This document specifies the requirements for construction, operation and testing of automatic electrical controls used in, on, or in association with an equipment. This document does not • apply to pressure sensing controls intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard. However, this document can be applied to evaluate automatic electrical controls intended specifically for industrial applications in cases where no relevant safety standard exists; • take into account the response value of an automatic action of a pressure sensing control, if such a response value is dependent upon
- Draft38 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft4 pagesEnglish languagesale 10% offe-Library read for×1 day
- 02-Oct-2025
- 33.100.20
- 2014/30/EU
- M/490
- CLC/TC 210
IEC 62453-1:2025 is available as IEC 62453-1:2025 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62453-1:2025 presents an overview and guidance for the IEC 62453 series. It • explains the structure and content of the IEC 62453 series (see Clause 5); • provides explanations of some aspects of the IEC 62453 series that are common to many of the parts of the series; • describes the relationship to some other standards; • provides definitions of terms used in other parts of the IEC 62453 series. This third edition cancels and replaces the first edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) introduction of a new implementation technology (defined in IEC TS 62453-43); b) introduction of an OPC UA information model for FDT (defined in IEC 62453-71).
- Draft51 pagesEnglish languagesale 10% offe-Library read for×1 day
- 02-Oct-2025
- 25.040.40
- 35.100.05
- 35.110
- CLC/TC 65X
IEC 63522-21:2025 This part is used for testing along with the appropriate severities and conditions for measurements and tests designed to assess the ability of DUTs to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method for evaluation of resistance against high temperature for long periods.
- Draft11 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 63208:2025 This document applies to the main functions of switchgear and controlgear and their assemblies, called equipment, in the context of operational technology (OT 3.1.34). It is applicable to equipment with wired or wireless data communication means and their physical accessibility, within their limits of environmental conditions. It is intended to achieve the appropriate physical and cybersecurity mitigation against vulnerabilities to security threats. This document provides requirements on the appropriate: – security risk assessment to be developed including the attack levels, the typical threats, the impact assessment and the relationship with safety; – levels of exposure of the communication interface and the determination of the equipment security level; – assessment of the exposure level of the communication interfaces; – assignment of the required security measures for the equipment; – countermeasures for the physical access and the environment derived from ISO/IEC 27001; – countermeasures referring to IEC 62443-4-2 with their criteria of applicability; – user instructions for installation, operation and maintenance; – conformance verification and testing, and – security protection profiles by family of equipment (Annex E to Annex I). In particular, it focuses on potential vulnerabilities to threats resulting in: – unintended operation, which can lead to hazardous situations; – unavailability of the protective functions (overcurrent, earth fault, etc.); – other degradation of main function. It also provides guidance on the cybersecurity management with the: – roles and responsibilities (Table 4); – typical architectures (Annex A); – use cases (Annex B); – development methods (Annex C); – recommendations to be provided to users and for integration into an assembly (Annex D); – bridging references to cybersecurity management systems (Annex K). This document does not cover security requirements for: – information technology (IT); – industrial automation and control systems (IACS), engineering workstations and their software applications; – critical infrastructure or energy management systems; – network device (communication network switch or virtual private network terminator), or – data confidentiality other than for critical security parameters; – design lifecycle management. For this aspect, see IEC 62443-4-1, ISO/IEC 27001 or other security lifecycle management standards.
- Draft129 pagesEnglish languagesale 10% offe-Library read for×1 day
- 02-Oct-2025
- 29.130.20
- CLC/SR 121
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.