EN 61167:1994
(Main)Metal halide lamps
Metal halide lamps
Superseded by EN 61167:2011
Halogen-Metalldampflampen
Lampes aux halogénures métalliques
Sijalke s kovinskim halidom (IEC 1167:1992)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-1998
Sijalke s kovinskim halidom (IEC 1167:1992)
Metal halide lamps (IEC 1167:1992)
Halogen-Metalldampflampen (IEC 1167:1992)
Lampes aux halogénures métalliques (CEI 1167:1992)
Ta slovenski standard je istoveten z: EN 61167:1994
ICS:
29.140.30 )OXRUHVFHQþQHVLMDONH6LMDONH Fluorescent lamps.
Discharge lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
NORME
CEI
INTERNATIONALE IEC
INTERNATIONAL
Première édition
STANDARD
First edition
1992-08
Lampes aux halogénures métalliques
Metal halide lamps
© CEI 1992 Droits de reproduction réservés — Copyright — all rights reserved
Aucune partie de cette publication ne peut étre reproduite ni
No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun pro-
any form or by any means, electronic or mechanical,
cédé, électronique ou mécanique, y compris la photocopie et
including photocopying and microfilm, without permission
les microfilms, sans l'accord riait de l'éditeur. in writing from the publisher.
Bureau Central de la Commiss io
n Electrotechnique Internationale 3, rue de Varembé
Genève, Suisse
Commission Electrotechnique Internationale
CODE PRIX
U
International Electrotechnical Commission
PRICE CODE
IEC
Me egyHapoAHaa 3nettTpoTexttwlecttaa
KOMNCCNA
Pour prix, voir catalogue en vigueur
For price, see current catalogue
1167©IEC —1—
SOMMAIRE
CONTENTS
Pages
Page
AVANT-PROPOS
FOREWORD 3
SECTION 1: GÉNÉRALITÉS
SECTION 1: GENERAL
Articles
Clause
1.1 Domaine d'application 4
1.1 Scope 5
1.2 Références normatives 4
1.2 Normative references 5
1.3 Définitions 4
1.3 Definitions 5
1.4 Marquage de la lampe 6
1.4 Lamp marking 7
1.5 Dimensions de la lampe 8
1.5 Lamp dimensions 9
1.6 Culots 8
1.6 Caps 9
1.7 Exigences relatives à l'essai 8
1.7 Test requirements 9
1.8
Renseignements pour la conception
1.8 Information for ballast, ignitor
des ballasts, des amorceurs et des
luminaire design and 9
luminaires 8
1.9 Feuilles schématiques des
1.9 Diagrammatic data sheets 11
caractéristiques 10
SECTION 2:
FEUILLES DE
SECTION 2: LAMP DATA SHEETS
CARACTÉRISTIQUES DES LAMPES
2.1 Système de numérotation des
2.1 Numbering system for lamp
feuilles de caractéristiques des
data sheets
lampes 10
2.2 Liste des types de
lampes
2.2 List of specific lamp types 11
spécifiques 10
_3-
1167©IEC
INTERNATIONAL ELECTROTECHNICAL COMMISSION
METAL HALIDE LAMPS
FOREWORD
1)
The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on
which all the National Committees having a special interest therein are represented, express, as nearly as
possible, an international consensus of opinion on the subjects dealt with.
2)
They have the form of recommendations for international use and they are accepted by the National
Committees in that sense.
3)
In order to promote international unification, the IEC expresses the wish that all National Committees
should adopt the text of the IEC recommendation for their national rules in so far as national conditions will
permit. Any divergence between the IEC recommendation and the corresponding national rules should, as
far as possible, be clearly indicated in the latter.
4)
The IEC has not laid down any procedure concerning marking as an indication of approval and has no
responsibility when an item of equipment is declared to comply with one of its recommendations.
This International standard has been prepared by Sub-Committee 34A: Lamps, of IEC
Technical Committee No. 34: Lamps and related equipment.
The text of this standard is based on the following documents:
DIS Reports on voting
Amendment to DIS Report on Voting
34A(CO)491
34A(CO)554 34A(CO)586
34A(CO)601
34A(CO)510 34A(CO)573
Full information on the voting for the approval of this standard can be found in the Voting
Reports indicated in the above table.
1167©IEC -5-
METAL HALIDE LAMPS
SECTION 1: GENERAL
1.1 Scope
This International Standard specifies the methods of test to be used for determining the
characteristics of metal halide lamps, both single-ended and double-ended, operated on
a.c. mains, 50 Hz or 60 Hz, with ballasts satisfying the requirements of IEC 923.
These requirements relate only to type testing.
The standard specifies lamp dimensions, electrical characteristics for lamp starting and
operation together with information for ballast, ignitor and luminaire design and colour
characteristics.
1.2 Normative references
The following normative documents contain provisions which, through reference in this
text, constitute provisions of this International Standard. At the time of publication, the
editions indicated were valid. All normative documents are subject to revision, and pa rties
to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated
below. Members of IEC and ISO maintain registers of currently valid International
Standards.
IEC 61: Lamp caps and holders together with gauges for the control of interchangeability
and safety.
IEC 61-1: 1969, Part 1 - Lamp caps including supplements 61-1A to 61-1N.
IEC 410: 1973, Sampling plans and procedures for inspection by attributes.
IEC 598-1: 1992, Luminaires - Part 1: General requirements and tests.
IEC 923: 1988, Ballasts for discharge lamps (excluding tubular fluorescent lamps).
Performance requirements.
1.3 Definitions
For the purposes of this International Standard the following definitions apply:
1.3.1 rated wattage: The wattage marked on the lamp, expressed in watts.
1167©IEC - 7 --
1.3.2 rated luminous flux: The luminous flux declared by the supplier, expressed in
lumens.
1.3.3 reference ballast: A special inductive type ballast complying with the requirements
of IEC 923 designed for use:
a) in testing lamps;
b) as comparison ballast in testing ballasts;
c) in selection of reference lamps. It is essentially characterized by a stable
voltage/current ratio and is relatively uninfluenced by variations in current, temperature
and magnetic surroundings.
The value of the current on which the calibration of the
1.3.4 calibration current:
reference ballast is based.
1.3.5 type test: A test or series of tests, made on a type test sample, for the purpose of
checking compliance of the design of a given product with the requirements of the relevant
specification.
1.3.6 type test sample: A sample consisting of one or more similar units submitted by
the manufacturer or the responsible vendor for the purpose of the type test.
rtion of
1.3.7 metal halide lamp: A high intensity discharge lamp in which the major po
the light is produced from a mixture of metallic vapour, metal halides and the products
of dissociation of metal halides.
NOTE - The definition covers clear and coated lamps.
1.3.8 colour: The colour characteristics of metal halide lamps are defined by the
chromaticity co-ordinates x and y and the general colour rendering index Ra.
The correlated colour temperature can be used as a guide to the colour appearance of the
lamp.
1.4 Lamp marking
The following information shall be distinctly and durably marked on the lamp:
mark of origin: this may take the form of a trade mark, the manufacturer's identifi-
a)
cation mark or the name of the responsible vendor;
b) rated wattage.
In addition, the following information may be given either on the lamp or in the supplier's
catalogue:
c) suitable advice on the colour appearance in the form of the manufacturer's code or
the correlated colour temperature.
1.5 Lamp dimensions
The lamp dimensions shall comply with the values given on the relevant lamp data sheet.
1167©IEC _9_
1.6 Caps
The caps on the finished lamps shall comply with the requirements of the relevant sheet of
IEC 61-1.
1.7 Test requirements
1.7.1 General remarks on tests
1.7.1.1 Tests according to these requirements are type tests.
NOTE - The requirements and tolerances permitted by this standard are related to testing of a
type test
sample submitted by the manufacturer for that purpose. In principle this
type test sample should consist of
units having characteristics typical of the manufacturer's production and be as close to the production
centre point values as possible.
It may be expected with the tolerances given in the standard that products manufactured in accordance
with the type test sample will ensure compliance with the standard for the majority of the production. Due to
the production spread it is inevitable, however, that there may be lamps outside the specified tolerances.
For guidance of sampling plans and procedures for inspection by attributes, see IEC 410.
1.7.1.2 For the tests the lamps shall be operated in free air or as specified in the
relevant lamp data sheet at an ambient temperature of 25 °C ± 5 °C on a 50 Hz or 60 Hz
sinusoidal power supply using the specific reference ballast at rated voltage and in the
operating position specified on the relevant lamp data sheet.
1.7.2
Lamp electrical characteristics
The lamp electrical characteristics shall comply with the values given in the relevant lamp
data sheet.
1.7.3 Lamp starting test
Requirements and test conditions are under consideration.
1.7.4 Luminous flux
The luminous flux of individual lamps shall be not less than 90 % of the rated value.
Test conditions are under consideration.
1.7.5 Colour characteristics
Test conditions are under consideration.
1.8 Information for ballast, ignitor and
luminaire design
In order to ensure reliable starting and operating conditions, ballasts, ignitors and
luminaires shall meet the requirements specified on the relevant lamp data sheet.
1167© IEC
1.9 Diagrammatic data sheets
Sheet number reference Description
1167-IEC-0001- Diagrammatic data sheet for location of single-ended metal halide
lamp dimensions
1167-IEC-0002- Diagrammatic data sheet for location of double-ended metal halide
lamp dimensions
SECTION 2: LAMP DATA SHEETS
2.1 Numbering system for lamp data sheets
The first number represents the number of this standard (1167) followed by the letters
"IEC".
The second number represents the lamp data sheet number.
The third number indicates the edition of the sheet.
Only those pages of the lamp data sheet which have been modified have a new edition
number. For example, the first page of the lamp data sheet 1167-IEC-1000-1 has been
modified, so this first page is now numbered 1167-IEC-1000-2. The following page of the
data sheet has not been modified and therefore retains the number 1167-IEC-1000-1.
2.2 List of specific lamp types
Correlated
Wattage colour Type Cap Sheet number
reference
temperature
W K
35 3 000 Single-ended G12 -IEC-1000-
70 3 000 Single-ended G12 -IEC-1050-
70 4 000* Single-ended G12 -IEC-1055-
G12 -IEC-1100-
150 3 000 Single-ended
150 4 000* Single-ended G12 -IEC-1105-
RX7s -IEC-2050-
70 3 000 Double-ended
70 4 200 Double-ended RX7s -IEC-2055-
150 3 000 Double-ended RX7s-24 -1EC-2100-
150 4 200 Double-ended RX7s-24 -IEC-2105-
• Under consideration.
1167 © IEC 1992
DIAGRAMMATIC DATA SHEET
FOR LOCATION OF SINGLE-ENDED
METAL HALIDE LAMP DIMENSIONS
Page 1
G12 cap*
•
Y ^
(8C .760/92
C = Light centre length
D= Arc length
' See sheet 7004-63 of IEC 61-1.
Texte français au verso
Publication CEI 1167
1167-IEC-0001-1
French text overleaf
IEC Publication 1167
OO
1167 I EC 1992
DIAGRAMMATIC DATA SHEET
FOR LOCATION OF DOUBLE-ENDED
METAL HALIDE LAMP DIMENSIONS
Page 1
RX7s Cap*
IEC 761/92
B= Insertion length
C = Light centre length
D= Arc length
Z= Contact-to-contact length
See sheet 7004-92A of IEC 61-1.
Texte français au verso
Publication CEI 1167
1167-IEC-0002-1
French text overleaf
IEC Publication 1167
1167 g
I EC 1992
METAL HALIDE LAMPS DATA SHEET
Page 1
Rating: 35 W/3 000 K Single-ended version Cap: G12
Electrical characteristics at 50 Hz and 60 Hz 1)
Objective Min. Max.
Lamp wattage W 39
Lamp voltage V 95* 85* 105*
Lamp current A 0,53
Run-up characteristics at nominal supply voltage 1)
Max. time to 90 % lumens Min I 2
Colour characteristics (nominal) 1)
Correlated colour temperature K 3 000
Chromaticity co-ordinates x/y 0,437/0,404
Colour rendering index Ra 2 80
Reference ballast characteristics at 50 Hz and 60 Hz
Rated frequency Hz 50/60
Rated voltage V 220
Calibration current A 0,53
Voltage/current ratio i2 350
Power factor 0,075 ± 0,005
Dimensions (see sheet 1167-IEC-0001)
mm
A: 26 max. B: 76 max.
C:56 ± 1 D: 4,0 ± 1
1) Values after 100 h ageing. Test position: vertical cap down ±5°
* Under consideration.
Texte français au verso Publication CEI 1167
67-IEC-^ ^OQ^ French text overleaf IEC Publication 1167
1167 © IEC 1992
METAL HALIDE LAMPS DATA SHEET
Page 2
Information for ballast design
Min. Max.
Open circuit voltage for starting (r.m.s.) V Under
consideration
Supply voltage for stable operation (r.m.s.) V 198
Ignitor information
Under consideration.
Further requirements
Min. Max.
Inrush current (peak) A 10,6
Warm-up current (r.m.s.) A 0,53 1,06
Because of a possible risk that abnormal operating conditions may occur at the end of lamp
life, which can lead to
ballast overloading, suitably protected circuits shall be used for operation of this lamp.
Information for luminaire design
Maximum permissible pinch temperature °C 280 Under consideration
Maximum permissible bulb temperature °C 450 Under consideration
Operating position
Any
The luminaire shall be provided with a safety screen (shattering and UV).
For requirements, see IEC 598-1.
Texte français au verso Publication CEt 1167
1167-
IEC-1000-1 French text overleaf IEC Publication 1167
SIST
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.