IEC 60317-68:2017
(Main)Specifications for particular types of winding wires - Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Specifications for particular types of winding wires - Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
IEC 60317-68:2017 specifies the requirements of enamelled rectangular aluminium winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The range of nominal conductor dimensions covered by this standard is
- width: min. 2,0 mm - max. 16,0 mm;
- thickness: min. 0,80 mm - max. 5,60 mm.
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specific ratio width/thickness are given in IEC 60317-0-9:2015.
Spécifications pour types particuliers de fils de bobinage - Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de polyvinyle, classe 120
IEC 60317-68:2017 spécifie les exigences relatives au fil de bobinage d’aluminium de section rectangulaire émaillé de classe 120 avec un revêtement unique à base de résine d’acétal de polyvinyle, qui peut être modifiée à condition de conserver la dénomination chimique de la résine d'origine et satisfaire à toutes les exigences spécifiées du fil. La plage de dimensions nominales du conducteur couverte par la présente norme est la suivante
- pour la largeur: min. 2,0 mm - max. 16,0 mm;
- pour l'épaisseur: min. 0,80 mm - max. 5,60 mm.
Les fils de grade 1 et de grade 2 sont inclus dans la présente partie de l'IEC 60317 et s’appliquent à la plage complète de conducteurs. Les combinaisons spécifiées de largeurs et d’épaisseurs ainsi que le rapport spécifique largeur/épaisseur sont donnés dans l’IEC 60317-0-9:2015.
Mots clés: des fils isolés utilisés dans les enroulements des appareils électriques, classe 120
General Information
Relations
Overview
IEC 60317-68:2017 (with amendments) is the international specification for polyvinyl acetal enamelled rectangular aluminium winding wire, class 120. It defines the required properties, dimensional limits and selected test criteria for rectangular aluminium conductors coated with a single polyvinyl acetal (or polyvinyl formal) based enamel. Modified resins are permitted provided they retain the chemical identity of the original resin and meet all specified requirements. This part is part of the IEC 60317 series and is intended to be read together with IEC 60317-0-9.
Key technical topics and requirements
- Conductor dimensions: nominal width from 2.0 mm to 16.0 mm and thickness from 0.80 mm to 5.60 mm; allowed width/thickness combinations and ratios are referenced to IEC 60317-0-9.
- Thermal class: Class 120 - minimum temperature index 120 and minimum heat shock resistance 155 °C.
- Grades: covers grade 1 and grade 2 for the full conductor range.
- Coating chemistry: single-layer coating based on polyvinyl acetal / polyvinyl formal; chemical identity must be retained if modified.
- Mechanical tests:
- Mandrel winding (flexibility): coating must show no cracks when bent flatwise and edgewise on mandrels sized per Table 1 (generally expressed as multiples of width or thickness).
- Adherence: wire stretched 15%; loss of adhesion distance must be less than one width.
- Electrical tests:
- Breakdown voltage measured with elevated temperature at 120 °C.
- Electrical resistance, elongation and other requirements reference IEC 60317-0-9 and applicable amendments.
- Tests marked “test inappropriate” in this part: springiness, cut-through, resistance to abrasion, continuity of insulation, resistance to refrigerants, solderability, heat/solvent bonding, dielectric dissipation factor, loss of mass, pin hole test - these are not required for this wire type in this standard.
- Packaging: follows Clause 30 of IEC 60317-0-9.
Practical applications and users
This standard is valuable for:
- Winding wire manufacturers specifying rectangular aluminium wire with polyvinyl acetal enamel.
- Design engineers of motors, transformers, inductors and electrical machines who require aluminium rectangular conductors with defined thermal and mechanical properties.
- Quality and test laboratories performing conformance testing against IEC criteria.
- Procurement and specification writers creating material specs for insulated aluminium winding wire.
Keywords: IEC 60317-68, polyvinyl acetal enamelled rectangular aluminium wire, class 120, winding wire specifications, temperature index, mandrel winding, adherence test.
Related standards
- IEC 60317-0-9:2015 (General requirements – enamelled rectangular aluminium wire)
- IEC 60851-4:2016 (Winding wires – Test methods – Chemical properties)
- IEC 60264 series (Packaging of winding wires)
- IEC 60317 series (other winding wire specifications)
For correct application, consult the full IEC 60317-68 document and the referenced normative clauses.
Standards Content (Sample)
IEC 60317-68 ®
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC 60317-68 ®
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.060.10 ISBN 978-2-8322-3841-7
– 2 – IEC 60317-68:2017 © IEC 2017
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
8.1 Mandrel winding test . 7
8.2 Adherence test . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10
Table 1 – Mandrel winding . 7
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organizati
...
IEC 60317-68 ®
Edition 1.2 2024-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.
IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.
Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 60317-68 ®
Edition 1.2 2024-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.060.10 ISBN 978-2-8322-9212-9
REDLINE VERSION – 2 – IEC 60317-68:2017+AMD1:2019
+AMD2:2024 CSV © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
8.1 Mandrel winding test . 7
8.2 Adherence test . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10
Table 1 – Mandrel winding . 8
+AMD2:2024 CSV © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s),
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
https://patents.iec.ch. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of the official IEC Standard and its amendments has been
prepared for user convenience.
IEC 60317-68 edition 1.2 contains the first edition (2017-01) [documents 55/1570/CDV
and 55/1591/RVC], its amendment 1 (2019-06) [documents 55/1694/CDV and
55/1744/RVC] and its amendment 2 (2024-06) [documents 55/1694/CDV and
55/1744/RVC].
In this Redline version, a vertical line in the margin shows where the technical content
is modified by amendments 1 and 2. Additions are in green text, deletions are in
strikethrough red text. A separate Final version with all changes accepted is available
in this publication.
REDLINE VERSION – 4 – IEC 60317-68:2017+AMD1:2019
+AMD2:2024 CSV © IEC 2024
International Standard IEC 60317-68 has been prepared by IEC technical committee 55:
Winding wires.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This International Standard is to be read in conjunction with IEC 60317-0-9:2015 and its
Amendment 1:2024.
A list of all parts in the IEC 60317, published under the general title Specifications for
particular types of winding wires, can be found on the IEC website.
The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in
order to reserve space for possible future wire requirements prior to those for wire packaging.
The committee has decided that the contents of this document and its amendments will
remain unchanged until the stability date indicated on the IEC website under webstore.iec.ch
in the data related to the specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
+AMD2:2024 CSV © IEC 2024
INTRODUCTION
This part of IEC 60317 forms an element of a series of standards which deals with insulated
wires used for windings in electrical equipment. The series has three groups describing:
1) Winding wires – Test methods (IEC 60851 series);
2) Specifications for particular types of winding wires (IEC 60317 series);
3) Packaging of winding wires (IEC 60264 series).
REDLINE VERSION – 6 – IEC 60317-68:2017+AMD1:2019
+AMD2:2024 CSV © IEC 2024
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
1 Scope
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 120 with a sole coating based on polyvinyl acetal or polyvinyl formal
resin, which may be modified providing it retains the chemical identity of the original resin and
meets all specified wire requirements.
NOTE 1 A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance of application characteristics.
NOTE 2 Polyvinyl acetal is a general name for a family of thermoplastic vinyl resins produced by the
condensation of polyvinyl alcohol with an aldehyde. Examples are polyvinyl acetal, polyvinyl formal and polyvinyl
butyral.
The range of nominal conductor dimensions covered by this standard is
Minimum Maximum
Width 2,0 mm 16,0 mm
Thickness 0,80 mm 5,60 mm
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specific ratio width/thickness
are given in IEC 60317-0-9.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60317-0-9:2015, Specifications for particular types of winding wires – Part 0-9: General
requirements – Enamelled rectangular aluminium wire.
IEC 60317-0-9:2015/AMD1:2024
IEC 60851-4:2016, Winding wires – Test methods – Part 4: Chemical properties
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60317-0-9:2015
apply.
+AMD2:2024 CSV © IEC 2024
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
IEC Electropedia: available at http://www.electropedia.org/
ISO Online browsing platform: available at http://www.iso.org/obp
3.2 General notes
3.2.1 Methods of test
Subclause 3.2.1 of IEC 60317-0-9:2015 and IEC 60317-0-9:2015/AMD1:2024 applies.
In case of inconsistencies between IEC 60317-0-9 and this part of IEC 60317 document, the
latter IEC 60317-68 shall prevail.
3.2.2 Winding wire
Class 120 is a thermal class that requires a minimum temperature index of 120 and a heat
shock resistance of at least 155 °C.
The temperature in degrees Celsius corresponding to the temperature index is not necessarily
that at which it is recommended that the wire be operated and this will depend on many
factors, including the type of equipment involved.
3.3 Appearance
See 3.3 of IEC 60317-0-9:2015.
4 Dimensions
Clause 4 of IEC 60317-0-9:2015 applies.
5 Electrical resistance
Clause 5 of IEC 60317-0-9:2015 and IEC 60317-0-9:2015/AMD1:2024applies.
6 Elongation
Clause 6 of IEC 60317-0-9:2015 applies.
7 Springiness
Test appropriate but no requirements specified.
Test inappropriate.
8 Flexibility and adherence
8.1 Mandrel winding test
The coating shall show no crack after the wire has been bent flatwise and edgewise on a
mandrel with a diameter as specified in Table 1.
REDLINE VERSION – 8 – IEC 60317-68:2017+AMD1:2019
+AMD2:2024 CSV © IEC 2024
Table 1 – Mandrel wi
...
IEC 60317-68 ®
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Spécifications pour types particuliers de fils de bobinage –
Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de polyvinyle,
classe 120
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 20 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub
Glossaire IEC - std.iec.ch/glossary
65 000 entrées terminologiques électrotechniques, en anglais
La recherche avancée permet de trouver des publications IEC
en utilisant différents critères (numéro de référence, texte, et en français, extraites des articles Termes et Définitions des
comité d’études,…). Elle donne aussi des informations sur les publications IEC parues depuis 2002. Plus certaines entrées
projets et les publications remplacées ou retirées. antérieures extraites des publications des CE 37, 77, 86 et
CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
csc@iec.ch.
IEC 60317-68 ®
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Spécifications pour types particuliers de fils de bobinage –
Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de
polyvinyle, classe 120
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-4730-3
– 2 – IEC 60317-68:2017 © IEC 2017
CONTENTS
CONTENTS . 2
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
8.1 Mandrel winding test . 7
8.2 Adherence test . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10
Table 1 – Mandrel winding . 7
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60317-68 has been prepared by IEC technical committee 55:
Winding wires.
This bilingual version (2017-08) corresponds to the monolingual English version, published in
2017-01.
The text of this standard is based on the following documents:
CDV Report on voting
55/1570/CDV 55/1591/RVC
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
The French version of this standard has not been voted upon.
– 4 – IEC 60317-68:2017 © IEC 2017
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This International Standard is to be read in conjunction with IEC 60317-0-9:2015.
A list of all parts in the IEC 60317, published under the general title Specifications for
particular types of winding wires, can be found on the IEC website.
The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in
order to reserve space for possible future wire requirements prior to those for wire packaging.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
INTRODUCTION
This part of IEC 60317 forms an element of a series of standards which deals with insulated
wires used for windings in electrical equipment. The series has three groups describing:
1) Winding wires – Test methods (IEC 60851 series);
2) Specifications for particular types of winding wires (IEC 60317 series);
3) Packaging of winding wires (IEC 60264 series).
– 6 – IEC 60317-68:2017 © IEC 2017
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
1 Scope
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be
modified providing it retains the chemical identity of the original resin and meets all specified
wire requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance of application characteristics.
The range of nominal conductor dimensions covered by this standard is
Minimum Maximum
Width 2,0 mm 16,0 mm
Thickness 0,80 mm 5,60 mm
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specific ratio width/thickness
are given in IEC 60317-0-9.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60317-0-9:2015, Specifications for particular types of winding wires – Part 0-9: General
requirements – Enamelled rectangular aluminium wire
IEC 60851-4:2016, Winding wires – Test methods – Part 4: Chemical properties
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60317-0-9:2015
apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.2 General notes
3.2.1 Methods of test
Subclause 3.2 of IEC 60317-0-9:2015 applies. In case of inconsisten
...
IEC 60317-68 ®
Edition 1.1 2019-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Spécifications pour types particuliers de fils de bobinage –
Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de polyvinyle,
classe 120
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - Electropedia - www.electropedia.org
webstore.iec.ch/advsearchform Le premier dictionnaire d'électrotechnologie en ligne au
La recherche avancée permet de trouver des publications IEC monde, avec plus de 22 000 articles terminologiques en
en utilisant différents critères (numéro de référence, texte, anglais et en français, ainsi que les termes équivalents dans
comité d’études,…). Elle donne aussi des informations sur les 16 langues additionnelles. Egalement appelé Vocabulaire
projets et les publications remplacées ou retirées. Electrotechnique International (IEV) en ligne.
IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary
Restez informé sur les nouvelles publications IEC. Just 67 000 entrées terminologiques électrotechniques, en anglais
Published détaille les nouvelles publications parues. et en français, extraites des articles Termes et Définitions des
Disponible en ligne et une fois par mois par email. publications IEC parues depuis 2002. Plus certaines entrées
antérieures extraites des publications des CE 37, 77, 86 et
Service Clients - webstore.iec.ch/csc CISPR de l'IEC.
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC 60317-68 ®
Edition 1.1 2019-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Spécifications pour types particuliers de fils de bobinage –
Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de
polyvinyle,
classe 120
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-7042-4
IEC 60317-68 ®
Edition 1.1 2019-06
CONSOLIDATED VERSION
REDLINE VERSION
VERSION REDLINE
colour
inside
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Spécifications pour types particuliers de fils de bobinage –
Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de polyvinyle,
classe 120
– 2 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
8.1 Mandrel winding test . 7
8.2 Adherence test . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10
Table 1 – Mandrel winding . 7
© IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of the official IEC Standard and its amendment has been
prepared for user convenience.
IEC 60317-68 edition 1.1 contains the fîrst edition (2017-01) [documents 55/1570/CDV
and 55/1591/RVC] and its amendment 1 (2019-06) [documents 55/1694/CDV and 55/1744/
RVC].
In this Redline version, a vertical line in the margin shows where the technical content
is modified by amendment 1. Additions are in green text, deletions are in strikethrough
red text. A separate Final version with all changes accepted is available in this
publication.
– 4 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
International Standard IEC 60317-68 has been prepared by IEC technical committee 55:
Winding wires.
The French version of this standard has not been voted upon.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This International Standard is to be read in conjunction with IEC 60317-0-9:2015.
A list of all parts in the IEC 60317, published under the general title Specifications for
particular types of winding wires, can be found on the IEC website.
The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in
order to reserve space for possible future wire requirements prior to those for wire packaging.
The committee has decided that the contents of the base publication and its amendment will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
© IEC 2019
INTRODUCTION
This part of IEC 60317 forms an element of a series of standards which deals with insulated
wires used for windings in electrical equipment. The series has three groups describing:
1) Winding wires – Test methods (IEC 60851 series);
2) Specifications for particular types of winding wires (IEC 60317 series);
3) Packaging of winding wires (IEC 60264 series).
– 6 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
1 Scope
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 120 with a sole coating based on polyvinyl acetal or polyvinyl formal
resin, which may be modified providing it retains the chemical identity of the original resin and
meets all specified wire requirements.
NOTE 1 A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance of application characteristics.
NOTE 2 Polyvinyl acetal is a general name for a family of thermoplastic vinyl resins produced by the
condensation of polyvinyl alcohol with an aldehyde. Examples are polyvinyl acetal, polyvinyl formal and polyvinyl
butyral.
The range of nominal conductor dimensions covered by this standard is
Minimum Maximum
Width 2,0 mm 16,0 mm
Thickness 0,80 mm 5,60 mm
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specific ratio width/thickness
are given in IEC 60317-0-9.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60317-0-9:2015, Specifications for particular types of winding wires – Part 0-9: General
requirements – Enamelled rectangular aluminium wire
IEC 60851-4:2016, Winding wires – Test methods – Part 4: Chemical properties
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60317-0-9:2015
apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
© IEC 2019
• ISO Online browsing platform: available at http://www.iso.org/obp
3.2 General notes
3.2.1 Methods of test
Subclause 3.2 of IEC 60317-0-9:2015 applies. In case of inconsistencies between
IEC 60317-0-9 and this part of IEC 60317, the latter shall prevail.
3.2.2 Winding wire
Class 120 is a thermal class that requires a minimum temperature index of 120 and a heat
shock resistance of at least 155 °C.
The temperature in degrees Celsius corresponding to the temperature index is not necessarily
that at which it is recommended that the wire be operated and this will depend on many
factors, including the type of equipment involved.
3.3 Appearance
See 3.3 of IEC 60317-0-9:2015.
4 Dimensions
Clause 4 of IEC 60317-0-9:2015 applies.
5 Electrical resistance
Clause 5 of IEC 60317-0-9:2015 applies.
6 Elongation
Clause 6 of IEC 60317-0-9:2015 applies.
7 Springiness
Test appropriate but no requirements specified.
8 Flexibility and adherence
8.1 Mandrel winding test
The coating shall show no crack after the wire has been bent flatwise and edgewise on a
mandrel with a diameter as specified in Table 1.
Table 1 – Mandrel winding
Wire bent on Mandrel diameter
Sizes up to and including 10 mm 2 x width
Width
Sizes over 10 mm 3 x width
Thickness All sizes 2 x thickness
– 8 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
8.2 Adherence test
The wire shall be stretched by 15 %. The distance of loss of adhesion shall be less than
1 x width.
9 Heat shock
Clause 9 of IEC 60317-0-9:2015 applies. The minimum heat shock temperature shall be
155 °C.
10 Cut-through
Test inappropriate
11 Resistance to abrasion
Test inappropriate
12 Resistance to solvents
Clause 12 of IEC 60317-0-9:2015 applies.
13 Breakdown voltage
Clause 13 of IEC 60317-0-9:2015 applies. The elevated temperature shall be 120 °C.
14 Continuity of insulation
Test inappropriate
15 Temperature index
Clause 15 of IEC 60317-0-9:2015 applies. The minimum temperature index shall be 120.
16 Resistance to refrigerants
Test inappropriate
17 Solderability
Test inappropriate
18 Heat or solvent bonding
Test inappropriate
19 Dielectric dissipation factor
Test inappropriate
© IEC 2019
20 Resistance to transformer oil
Test according to Clause 6 of IEC 60851-4:2016 appropriate. Test requirements are under
consideration.
21 Loss of mass
Test inappropriate
23 Pin hole test
Test inappropriate
30 Packaging
Clause 30 of IEC 60317-0-9:2015 applies.
– 10 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
Bibliography
IEC 60264 (all parts), Packaging of winding wires
IEC 60317 (all parts), Specifications for particular types of winding wires
IEC 60851 (all parts), Winding wires – Test methods
___________
– 12 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
SOMMAIRE
AVANT-PROPOS . 13
INTRODUCTION . 15
1 Domaine d’application . 16
2 Références normatives . 16
3 Termes, définitions, notes générales et aspect . 16
3.1 Termes et définitions . 16
3.2 Notes générales . 17
3.2.1 Méthodes d’essai . 17
3.2.2 Fil de bobinage . 17
3.3 Aspect . 17
4 Dimensions. 17
5 Résistance électrique . 17
6 Allongement . 17
7 Effet de ressort . 17
8 Souplesse et adhérence . 17
8.1 Essai d’enroulement sur mandrin . 17
8.2 Essai d’adhérence . 18
9 Choc thermique . 18
10 Thermoplasticité . 18
11 Résistance à l’abrasion . 18
12 Résistance aux solvants . 18
13 Tension de claquage . 18
14 Continuité de l’isolant . 18
15 Indice de température . 18
16 Résistance aux réfrigérants . 18
17 Brasabilité . 18
18 Adhérence par chaleur ou par solvant. 19
19 Facteur de dissipation diélectrique . 19
20 Résistance à l’huile de transformateur . 19
21 Perte de masse . 19
23 Détection des microfissures en immersion . 19
30 Conditionnement . 19
Bibliographie . 20
Tableau 1 – Enroulement sur mandrin. 18
© IEC 2019
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
SPÉCIFICATIONS POUR TYPES PARTICULIERS DE FILS DE BOBINAGE –
Partie 68: Fil d’aluminium de section rectangulaire émaillé
d’acétal de polyvinyle, classe 120
AVANT-PROPOS
1) La Commission Electrotechnique Internationale (IEC) est une organisation mondiale de normalisation
composée de l'ensemble des comités électrotechniques nationaux (Comités nationaux de l’IEC). L’IEC a pour
objet de favoriser la coopération internationale pour toutes les questions de normalisation dans les domaines
de l'électricité et de l'électronique. À cet effet, l’IEC – entre autres activités – publie des Normes
internationales, des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au
public (PAS) et des Guides (ci-après dénommés "Publication(s) de l’IEC"). Leur élaboration est confiée à des
comités d'études, aux travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les
organisations internationales, gouvernementales et non gouvernementales, en liaison avec l’IEC, participent
également aux travaux. L’IEC collabore étroitement avec l'Organisation Internationale de Normalisation (ISO),
selon des conditions fixées par accord entre les deux organisations.
2) Les décisions ou accords officiels de l’IEC concernant les questions techniques représentent, dans la mesure
du possible, un accord international sur les sujets étudiés, étant donné que les Comités nationaux de l’IEC
intéressés sont représentés dans chaque comité d’études.
3) Les Publications de l’IEC se présentent sous la forme de recommandations internationales et sont agréées
comme telles par les Comités nationaux de l’IEC. Tous les efforts raisonnables sont entrepris afin que l’IEC
s'assure de l'exactitude du contenu technique de ses publications; l’IEC ne peut pas être tenue responsable de
l'éventuelle mauvaise utilisation ou interprétation qui en est faite par un quelconque utilisateur final.
4) Dans le but d'encourager l'uniformité internationale, les Comités nationaux de l’IEC s'engagent, dans toute la
mesure possible, à appliquer de façon transparente les Publications de l’IEC dans leurs publications nationales
et régionales. Toutes divergences entre toutes Publications de l’IEC et toutes publications nationales ou
régionales correspondantes doivent être indiquées en termes clairs dans ces dernières.
5) L’IEC elle-même ne fournit aucune attestation de conformité. Des organismes de certification indépendants
fournissent des services d'évaluation de conformité et, dans certains secteurs, accèdent aux marques de
conformité de l’IEC. L’IEC n'est responsable d'aucun des services effectués par les organismes de certification
indépendants.
6) Tous les utilisateurs doivent s'assurer qu'ils sont en possession de la dernière édition de cette publication.
7) Aucune responsabilité ne doit être imputée à l’IEC, à ses administrateurs, employés, auxiliaires ou
mandataires, y compris ses experts particuliers et les membres de ses comités d'études et des Comités
nationaux de l’IEC, pour tout préjudice causé en cas de dommages corporels et matériels, ou de tout autre
dommage de quelque nature que ce soit, directe ou indirecte, ou pour supporter les coûts (y compris les frais
de justice) et les dépenses découlant de la publication ou de l'utilisation de cette Publication de l’IEC ou de
toute autre Publication de l’IEC, ou au crédit qui lui est accordé.
8) L'attention est attirée sur les références normatives citées dans cette publication. L'utilisation de publications
référencées est obligatoire pour une application correcte de la présente publication.
9) L’attention est attirée sur le fait que certains des éléments de la présente Publication de l’IEC peuvent faire
l’objet de droits de brevet. L’IEC ne saurait être tenue pour responsable de ne pas avoir identifié de tels droits
de brevets et de ne pas avoir signalé leur existence.
Cette version consolidée de la Norme IEC officielle et de son amendement a été
préparée pour la commodité de l'utilisateur.
L'IEC 60317-68 édition 1.1 contient la première édition (2017-01) [documents 55/1570/
CDV et 55/1591/RVC] et son amendement 1 (2019-06) [documents 55/1694/CDV et
55/1744/RVC].
Dans cette version Redline, une ligne verticale dans la marge indique où le contenu
technique est modifié par l'amendement 1. Les ajouts sont en vert, les
suppressions sont en rouge, barrées. Une version Finale avec toutes les
modifications acceptées est disponible dans cette publication.
– 14 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
La Norme internationale IEC 60317-68 a été établie par le comité d’études 55 de l'IEC: Fils
de bobinage.
La version française de cette norme n'a pas été soumise au vote.
Ce document a été rédigé selon les Directives ISO/IEC, Partie 2.
Cette Norme internationale doit être lue conjointement avec l’IEC 60317-0-9:2015.
Une liste de toutes les parties de l'IEC 60317, publiées sous le titre général Spécifications
pour types particuliers de fils de bobinage, peut être consultée sur le site web de l'IEC.
La numérotation des articles dans la présente norme n'est pas continue entre les Article 21
et 30 afin de permettre l'introduction d'éventuelles futures exigences pour les fils avant celles
concernant le conditionnement des fils.
Le comité a décidé que le contenu de la publication de base et de son amendement ne sera
pas modifié avant la date de stabilité indiquée sur le site web de l’IEC
sous "http://webstore.iec.ch" dans les données relatives à la publication recherchée. A cette
date, la publication sera
• reconduite,
• supprimée,
• remplacée par une édition révisée, ou
• amendée.
IMPORTANT – Le logo "colour inside" qui se trouve sur la page de couverture de cette
publication indique qu'elle contient des couleurs qui sont considérées comme utiles à
une bonne compréhension de son contenu. Les utilisateurs devraient, par conséquent,
imprimer cette publication en utilisant une imprimante couleur.
© IEC 2019
INTRODUCTION
La présente partie de l'IEC 60317 constitue l'un des éléments d’une série de normes traitant
des fils isolés utilisés dans les enroulements des appareils électriques. Cette série est
composée de trois groupes définissant respectivement:
1) Fils de bobinage – Méthodes d'essai (série IEC 60851);
2) Spécifications pour types particuliers de fils de bobinage (série IEC 60317);
3) Conditionnement des fils de bobinage (série IEC 60264).
– 16 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
SPÉCIFICATIONS POUR TYPES PARTICULIERS DE FILS DE BOBINAGE –
Partie 68: Fil d’aluminium de section rectangulaire émaillé
d’acétal de polyvinyle, classe 120
1 Domaine d’application
La présente partie de l'IEC 60317 spécifie les exigences relatives au fil de bobinage
d’aluminium de section rectangulaire émaillé de classe 120 avec un revêtement unique à
base de résine d’acétal de polyvinyle ou de résine de polyformal de vinyle, qui peut être
modifiée à condition de conserver la dénomination chimique de la résine d'origine et satisfaire
à toutes les exigences spécifiées du fil.
NOTE 1 Une résine modifiée est une résine qui a subi une modification chimique, ou qui contient un ou plusieurs
additifs pour améliorer certaines performances des caractéristiques d'application.
NOTE 2 Le terme d'acétal de polyvinyle est une dénomination générale correspondant à une famille de résines
vinyliques thermoplastiques produites par la condensation de polyalcool de vinyle avec un aldéhyde. À titre
d'exemples, on peut citer l'acétal de polyvinyle, le polyformal de vinyle et le polybutyral de vinyle.
La plage de dimensions nominales du conducteur couverte par la présente norme est la
suivante
Minimale Maximale
Largeur 2,0 mm 16,0 mm
Epaisseur 0,80 mm 5,60 mm
Les fils de grade 1 et de grade 2 sont inclus dans la présente partie de l'IEC 60317 et
s’appliquent à la plage complète de conducteurs.
Les combinaisons spécifiées de largeurs et d’épaisseurs ainsi que le rapport spécifique
largeur/épaisseur sont donnés dans l’IEC 60317-0-9.
2 Références normatives
Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu,
des exigences du présent document. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence
s'applique (y compris les éventuels amendements).
IEC 60317-0-9:2015, Spécifications pour types particuliers de fils de bobinage – Partie 0-9:
Exigences générales – Fil de section rectangulaire émaillé en aluminium
IEC 60851-4:2016, Fils de bobinage – Méthodes d'essai – Partie 4: Propriétés chimiques
3 Termes, définitions, notes générales et aspect
3.1 Termes et définitions
Pour les besoins du présent document, les termes et définitions de l'IEC 60317-0-9:2015
s’appliquent.
© IEC 2019
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées
en normalisation, consultables aux adresses suivantes:
• IEC Electropedia: disponible à l'adresse http://www.electropedia.org/
• ISO Online browsing platform: disponible à l'adresse http://www.iso.org/obp
3.2 Notes générales
3.2.1 Méthodes d’essai
Le paragraphe 3.2 de l’IEC 60317-0-9:2015 s’applique. En cas de divergences entre
l’IEC 60317-0-9 et la présente partie de l’IEC 60317, cette dernière doit prévaloir.
3.2.2 Fil de bobinage
La classe 120 est une classe thermique qui exige un indice minimal de température de 120 et
une résistance au choc thermique d’au moins 155 °C.
La température en degrés Celsius correspondant à l'indice de température n'est pas
nécessairement celle à laquelle il est recommandé d’utiliser le fil et ceci dépend de nombreux
facteurs dont le type d'équipement utilisé.
3.3 Aspect
Voir 3.3 de l’IEC 60317-0-9:2015.
4 Dimensions
L’Article 4 de l’IEC 60317-0-9:2015 s’applique.
5 Résistance électrique
L’Article 5 de l’IEC 60317-0-9:2015 s’applique.
6 Allongement
L’Article 6 de l’IEC 60317-0-9:2015 s’applique.
7 Effet de ressort
L’essai s’applique, mais aucune exigence n’est spécifiée.
8 Souplesse et adhérence
8.1 Essai d’enroulement sur mandrin
Le revêtement ne doit présenter aucune craquelure après pliage du fil à plat et sur chant sur
un mandrin dont le diamètre est spécifié dans le Tableau 1.
– 18 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
Tableau 1 – Enroulement sur mandrin
Fil plié sur Diamètre du mandrin
Des tailles jusqu’à 10 mm inclus 2 x largeur
Largeur
Des tailles supérieures à 10 mm 3 x largeur
Epaisseur Toutes les tailles 2 x épaisseur
8.2 Essai d’adhérence
Le fil doit être soumis à un étirement de 15 %. La distance de perte d’adhérence doit être
inférieure à 1 x largeur.
9 Choc thermique
L’Article 9 de l’IEC 60317-0-9:2015 s’applique. La température minimale de choc thermique
doit être de 155 °C.
10 Thermoplasticité
L’essai ne s’applique pas
11 Résistance à l’abrasion
L’essai ne s’applique pas
12 Résistance aux solvants
L’Article 12 de l’IEC 60317-0-9:2015 s’applique.
13 Tension de claquage
L’Article 13 de l’IEC 60317-0-9:2015 s’applique. La température élevée doit être de 120 °C.
14 Continuité de l’isolant
L’essai ne s’applique pas
15 Indice de température
L’Article 15 de l’IEC 60317-0-9:2015 s’applique. L’indice minimal de température doit être
de 120.
16 Résistance aux réfrigérants
L’essai ne s’applique pas
17 Brasabilité
L’essai ne s’applique pas
© IEC 2019
18 Adhérence par chaleur ou par solvant
L’essai ne s’applique pas
19 Facteur de dissipation diélectrique
L’essai ne s’applique pas
20 Résistance à l’huile de transformateur
L’essai conforme à l’Article 6 de l’IEC 60851-4:2016 s’applique. Des exigences d’essai sont à
l’étude.
21 Perte de masse
L’essai ne s’applique pas
23 Détection des microfissures en immersion
L’essai ne s’applique pas
30 Conditionnement
L’Article 30 de l’IEC 60317-0-9:2015 s’applique.
– 20 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
Bibliographie
IEC 60264 (toutes les parties), Conditionnement des fils de bobinage
IEC 60317 (toutes les parties), Spécifications pour types particuliers de fils de bobinage
IEC 60851 (toutes les parties), Fils de bobinage – Méthodes d'essai
___________
IEC 60317-68 ®
Edition 1.1 2019-06
CONSOLIDATED VERSION
FINAL VERSION
VERSION FINALE
colour
inside
Specifications for particular types of winding wires –
Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Spécifications pour types particuliers de fils de bobinage –
Partie 68: Fil d’aluminium de section rectangulaire émaillé d’acétal de polyvinyle,
classe 120
– 2 – IEC 60317-68:2017+AMD1:2019 CSV
© IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
8.1 Mandrel winding test . 7
8.2 Adherence test . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography .
...
Frequently Asked Questions
IEC 60317-68:2017 is a standard published by the International Electrotechnical Commission (IEC). Its full title is "Specifications for particular types of winding wires - Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120". This standard covers: IEC 60317-68:2017 specifies the requirements of enamelled rectangular aluminium winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The range of nominal conductor dimensions covered by this standard is - width: min. 2,0 mm - max. 16,0 mm; - thickness: min. 0,80 mm - max. 5,60 mm. Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specific ratio width/thickness are given in IEC 60317-0-9:2015.
IEC 60317-68:2017 specifies the requirements of enamelled rectangular aluminium winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The range of nominal conductor dimensions covered by this standard is - width: min. 2,0 mm - max. 16,0 mm; - thickness: min. 0,80 mm - max. 5,60 mm. Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specific ratio width/thickness are given in IEC 60317-0-9:2015.
IEC 60317-68:2017 is classified under the following ICS (International Classification for Standards) categories: 29.060.10 - Wires; 31.080.01 - Semiconductor devices in general. The ICS classification helps identify the subject area and facilitates finding related standards.
IEC 60317-68:2017 has the following relationships with other standards: It is inter standard links to IEC 60317-68:2017/AMD1:2019, IEC 60317-68:2017/AMD2:2024. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase IEC 60317-68:2017 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of IEC standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...