ISO/R 261:1969
(Main)Title missing - Legacy paper document
Title missing - Legacy paper document
General Information
Buy Standard
Standards Content (Sample)
Ref. No. : ISO/R 261-1969 (E)
üDC 621.882.082.1 (100)
IS0
I N T E RN AT I O N A L O R G A N I Z AT I O N FOR STAND AR D 1 ZAT I O N
IS0 RECOMMENDATION
R 261
IS0 GENERAL PURPOSE METRIC SCREW THREADS
GENERAL PLAN
2nd EDITION
r' September 1969
This second edition supersedes the first edition.
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
belongs to IS0 Member Bodies. Reproduction of these
documents, in any country, may be authorized therefore only
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
Printed in Switzerland
Also issued in French and Russian. Copies to be. obtained through the national standards organizations.
---------------------- Page: 1 ----------------------
-3-
BRIEF HISTORY
The IS0 Recommendation R 261, IS0 metric screw threads - General pbn (diameter range 0.25 to 300 mm), was drawn
up by Technical Committee ISO/TC 1, Screw threads, the Secretariat of which is held by the Svenges Standardiseringskommission (SIS).
Work on this question led to the adoption of a Dràft IS0 Recommendation.
In May 1960, this Draft IS0 Recommendation (No. 297) was circulated to all the IS0 Member Bodies for enquiry. It was
approved by 30 Member Bodies. One Member Body opposed the approval of the Draft.
This Draft IS0 Recommendation was then submitted by correspondence to the IS0 Council, which decided, in July 1962,
to accept it as an IS0 RECOMMENDATION.
L
BRIEF HISTORY RELATING TO THE 2nd EDITION
In 1967, Technical Committee ISO/TC 1 decided to revise the IS0 Recommendation R 261-1962, deleting
the sizes below 1 mm, and a Draft IS0 Recommendation was adopted to this effect.
In May 1968, this Draft IS0 Recommendation (No. 1499) was circulated to all the IS0 Member Bodies for
enquiry. It was approved, subject to a few modifications of an editorial nature, by the following Member Bodies :
Austria Israel South Africa, Rep. of
Belgium Italy Spain
Canada Japan Sweden
Chile Korea, Rep. of Switzerland
Czechoslovakia Net herlands Thailand
Cuba New Zealand Turkey
Denmark Norway U.A.R.
France r' Peru United Kingdom
Germany Poland U. S.S. R.
Hungary Portugal
India Romania
Two Member Bodies opposed the approval of the Draft :
Australia
U.S.A.
This Draft IS0 Recommendation was then submitted by correspondence to the IS0 Council, which decided,
in September 1969, to accept it as a revision of IS0 Recommendation R 261-1962, the title of which is modified
as follows ; IS0 general purpose metric screw threads - General plan.
This edition (2nd edition) cancels and replaces the first edition of IS0 Recommendation R 261-1962.
---------------------- Page: 2 ----------------------
-4- ISO/R 261-1969 (E)
FOREWORD
Thi
...
Réf. No : ISO/R 261-1969 (F)
CDU 621.882.082.1 (100)
IS0
ORGAN I SAT1 ON I NT ERN AT1 ON A LE
DE NORM A LIS AT1 ON
RECOMMANDATION IS0
R 261
FILETAGES MÉTRIQUES ISO POUR USAGES GÉNÉRAUX
VUE D’ENSEMBLE
2ème ED IT I ON
Septembre 1969
r‘
Cette deuxième édition annule et remplace la première édition
REPRODUCïION INTERDITE
Le droit de reproduction des Recommandations IS0 et des Normes
IS0 est la propriéte des Comités Membres de 1’ISO. En const-
quence, dans chaque pays, la reproduction de ces documents ne
peut être autorisée que par l’organisation nationale de normali-
sation de ce pays, membre de I’ISO.
Seules les normes nationales sont valables dans leurs pays respectifs.
Imprimé en Suisse
Ce document est également éditk en anglais et en russe. I1 peut être obtenu auprès des organisations
nationales de normalisation.
---------------------- Page: 1 ----------------------
3-
HISTORIQUE
La Recommandation ISO/R 261, Filetages métriques IS0 - Vue d’ensemble (diamètres de 0,25 Ù 300 mm), a été élaborée
par le Comité Technique ISO/TC 1, Filetages, dont le Secrétariat est assuré par la Sveriges Standardiseringskommission (SIS).
Les travaux relatifs à cette question aboutirent à l’adoption d’un Projet de Recommandation ISO.
En mai 1960, ce Projet de Recommandation IS0 (NO 297) fut soumis à l’enquête de tous les Comités Membres de l’IS0.
11 fut approuvé par 30 Comités Membres. Un Comité Membre se déclara opposé à l’approbation du Projet.
Ce Projet de Recommandation IS0 fut alors soumis par correspondance au Conseil de VISO qui décida, en juillet 1962,
de l’accepter comme RECOMMANDATION ISO.
HISTORIQUE RELATIF À LA 2ème EDITION
En 1967, le Comité Technique ISO/TC 1 décida de reviser la Recommandation ISOiR 261-1962, en
supprimant les dimensions inférieures à 1 mm, et un Projet de Recommandation IS0 fut adopté à cet effet.
En mai 1968, ce Projet de Recommandation IS0 (NO 1499) fut soumis a l’enquête de tous les Comités
Membres de I’ISO. I1 fut approuvé, sous réserve de quelques modifications d’ordre rédactionnel, par les Comités
Membres suivants :
Hongrie R.A.U.
Afrique du Sud, Rép. d’
Roumanie
Allemagne Inde
Israël Royaume-Uni
Autriche
Suède
Belgique Italie
Canada Japon Suisse
Chili Norvège Tchécoslovaquie
Corée, Rép. de Nouvelle-Zélande Thaïlande
Cuba r‘
Pays-Bas Turquie
Danemark Pérou U.R.S.S.
Espagne Pologne
Portugal
France
Deux Comités Membres se déclarèrent opposés à l’approbation du Projet :
Australie
U.S.A.
Ce Projet de Recommandation IS0 fut alors soumis par correspondance au Conseil de I’ISO qui décida,
en septembre 1969, de I’accepter comme revision de la Recommandation ISO/R 261-1962 dont le titre a été
modifié comme suit : Filetages métriques IS0 pour usages généraux - Vue d’ensemble.
La présente édition (2ème édition) annule et remplace la première édition de la Recommandation ISO/R 261-1962.
---------------------- Page: 2 ----------------------
-4-
ISO/R 26 1 -1 969 (F)
AVANT-PROPOS
Le présent document fait partie d'une série de Recommandations IS0 définissant les filetages IS0 pour usages
généraux. Les Recommandations IS0 connexes sont les suivantes :
(2ème édition - 1969), Filetages IS0 pour usages généraux - Profil de base;
ISO/R 68
ISO/R 262 (2ème édition - 1969), Filetages métriques IS0 pour usages généraux - Sélection de dimensions
pour la boulonnerie;
ISO/R 724, Filetages métriques IS0 pour usages généraux - Dimensions de base.
---------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.