SIST EN 303 423 V1.3.1:2021
Environmental Engineering (EE) - Electrical and electronic household and office equipment - Measurement of networked standby power consumption of Interconnecting equipment
Environmental Engineering (EE) - Electrical and electronic household and office equipment - Measurement of networked standby power consumption of Interconnecting equipment
The present document specifies methods of measurement of electrical power consumption in networked standby and the
reporting of the results for network interconnecting equipment.
Example of interconnecting equipment are in Annex B.
Power consumption in standby (other than networked standby) is covered by EN 50564 [1], including the input voltage
range.
The present document also provides a method to test power management and whether it is possible to deactivate
wireless network connection(s).
The present document applies to electrical products with a rated input voltage of 230 V a.c. for single phase products
and 400 V a.c. for three phase products.
The present document is produced under the mandate M/544 and can be used to demonstrate compliance to the EU
Regulation (EC) No 1275/2008 [i.1] amended by Regulation (EU) 801/2013 [i.2].
The present document does not apply to televisions as defined in Regulation (EC) No 642/2009 [i.10].
NOTE 1: The EU regulation 801/2013 [i.2] applies to equipment designed for use with a nominal voltage rating of
250 V and below.
NOTE 2: EU regulation 801/2013 [i.2] does not apply to electrical and electronic household and office equipment
placed on the market with a low voltage external power supply to work as intended.
NOTE 3: "Low voltage external power supply" is the definition provided in EU regulation 278/2009 [i.3].
NOTE 4: The measurement of energy consumption and performance of equipment during intended use are
generally specified in product standards and are not covered by the present document.
NOTE 5: Where the present document is referenced by more specific standards or procedures, these should define
and name the relevant conditions to which this test procedure is applied.
1.2 Equipment not in the scope of the present document
The present document does not apply to the measurement of electrical power consumption in networked standby for
edge equipment. The edge equipment is a networked equipment that can be connected to a network and interact with
that network or other devices and that does not have, as its primary function, the passing of network traffic to provide a
network. Edge equipment are covered in EN 50643 [i.8].
Okoljski inženiring (EE) - Električna in elektronska gospodinjska in pisarniška oprema - Meritve porabe energije povezovalne opreme v omrežni pripravljenosti
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 303 423 V1.3.1:2021
01-september-2021
Okoljski inženiring (EE) - Električna in elektronska gospodinjska in pisarniška
oprema - Meritve porabe energije povezovalne opreme v omrežni pripravljenosti
Environmental Engineering (EE) - Electrical and electronic household and office
equipment - Measurement of networked standby power consumption of Interconnecting
equipment
Ta slovenski standard je istoveten z: ETSI EN 303 423 V1.3.1 (2021-07)
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
27.015 Energijska učinkovitost. Energy efficiency. Energy
Ohranjanje energije na conservation in general
splošno
35.260 Pisarniški stroji Office machines
SIST EN 303 423 V1.3.1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 423 V1.3.1:2021
---------------------- Page: 2 ----------------------
SIST EN 303 423 V1.3.1:2021
ETSI EN 303 423 V1.3.1 (2021-07)
HARMONISED EUROPEAN STANDARD
Environmental Engineering (EE);
Electrical and electronic household and office equipment;
Measurement of networked standby power consumption of
Interconnecting equipment
---------------------- Page: 3 ----------------------
SIST EN 303 423 V1.3.1:2021
2 ETSI EN 303 423 V1.3.1 (2021-07)
Reference
REN/EE-007005
Keywords
customer premises networks, energy efficiency,
network, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 423 V1.3.1:2021
3 ETSI EN 303 423 V1.3.1 (2021-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
1.1 Equipment in the scope of the present document . 7
1.2 Equipment not in the scope of the present document . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Information required for testing purposes . 10
4.1 Information about networked port(s) . 10
4.2 Power management function - periods & conditions . 11
4.3 Activation and deactivation of wireless network connections . 11
5 Measurement conditions. 11
5.1 Common requirements . 11
5.2 Test room. 12
5.3 Power supply . 12
5.4 Power measuring instruments. 12
5.5 Configuration of network ports . 12
5.6 Measurement uncertainty . 14
6 Measurement procedures . 15
6.1 General . 15
6.2 Wireless network port management . 15
6.2.0 General . 15
6.2.1 Test sequence . 15
6.2.2 Verifying that wireless connections are deactivated . 15
6.2.3 Verifying that wireless logical network port is active. 15
6.3 Preparation of the EUT and general testing aspects . 15
6.4 Power management, reactivation and networked standby power consumption . 16
6.5 Measurement of standby power consumption with all network ports disconnected . 17
6.6 Measurement of networked standby power consumption with all network ports connected . 17
7 Test report . 17
7.1 Test and laboratory details. 17
7.2 Details of product under test. 17
7.3 Test parameters and network configuration . 18
7.4 Measured and documented data . 18
Annex A (informative): Relationship between the present document and the ecodesign
requirements of Commission Regulation (EC) No 1275/2008, as
amended by Commission Regulation (EU) No 801/2013 . 19
Annex B (informative): Equipment classification . 22
B.1 General . 22
Annex C (informative): General information on network technologies and network
configurations with respect to power consumption . 24
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 423 V1.3.1:2021
4 ETSI EN 303 423 V1.3.1 (2021-07)
C.1 Examples of network port configuration . 24
Annex D (informative): Information to be provided to the user and other interested parties . 25
D.1 Information to be provided to the user and other interested parties . 25
D.1.1 Information available on-line . 25
D.1.2 Information available in the user manual . 25
Annex E (informative): Example of a test report template . 26
Annex F (informative): Bibliography . 28
Annex G (informative): Change history . 29
History . 30
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 423 V1.3.1:2021
5 ETSI EN 303 423 V1.3.1 (2021-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Environmental
Engineering (EE).
The present document has been prepared under the Commission's standardisation request M/544, C(2015) 9468 final of
5 January 2016, to the European standardisation organizations as regards ecodesign requirements for networked standby
in support of Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] (see note 2), to provide one
voluntary means of conforming to the ecodesign requirements on networked standby of the following:
• Commission Regulation (EC) No 1275/2008 [i.1] of 17 December 2008 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for standby and off
mode, and networked standby, electric power consumption of electrical and electronic household and office
equipment; and
• Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC of the
European Parliament and of the Council with regard to ecodesign requirements for televisions.
NOTE 1: Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] were amended by
Commission Regulation (EU) No 801/2013 [i.2] of 22 August 2013.
NOTE 2: Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for televisions is
quoted in the introduction of annex A, but no relationship with the present document and the requirements
of Commission Regulation (EC) No 642/2009 are provided because televisions are out of scope of the
present document.
Once the present document is cited in the Official Journal of the European Union under that Regulation, compliance
with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding ecodesign requirements of that Regulation and
associated EFTA Regulations.
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 423 V1.3.1:2021
6 ETSI EN 303 423 V1.3.1 (2021-07)
National transposition dates
Date of adoption of this EN: 29 June 2021
Date of latest announcement of this EN (doa): 30 September 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2022
Date of withdrawal of any conflicting National Standard (dow): 31 March 2023
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The methods defined in the present document are intended to define requirements for the measurement of the power
consumed by the interconnecting equipment having one or more wired or wireless networked port(s) able to resume a
function by way of a remotely initiated trigger or reactivation trigger from a network connection. The present document
also provides a method to test power management and whether it is possible to deactivate wireless network
connection(s).
For the measurement of low power modes, reference is made to EN 50564 [1].
ETSI
---------------------- Page: 8 ----------------------
SIST EN 303 423 V1.3.1:2021
7 ETSI EN 303 423 V1.3.1 (2021-07)
1 Scope
1.1 Equipment in the scope of the present document
The present document specifies methods of measurement of electrical power consumption in networked standby and the
reporting of the results for network interconnecting equipment.
Example of interconnecting equipment are in Annex B.
Power consumption in standby (other than networked standby) is covered by EN 50564 [1], including the input voltage
range.
The present document also provides a method to test power management and whether it is possible to deactivate
wireless network connection(s).
The present document applies to electrical products with a rated input voltage of 230 V a.c. for single phase products
and 400 V a.c. for three phase products.
The present document is produced under the mandate M/544 and can be used to demonstrate compliance to the EU
Regulation (EC) No 1275/2008 [i.1] amended by Regulation (EU) 801/2013 [i.2].
The present document does not apply to televisions as defined in Regulation (EC) No 642/2009 [i.10].
NOTE 1: The EU regulation 801/2013 [i.2] applies to equipment designed for use with a nominal voltage rating of
250 V and below.
NOTE 2: EU regulation 801/2013 [i.2] does not apply to electrical and electronic household and office equipment
placed on the market with a low voltage external power supply to work as intended.
NOTE 3: "Low voltage external power supply" is the definition provided in EU regulation 278/2009 [i.3].
NOTE 4: The measurement of energy consumption and performance of equipment during intended use are
generally specified in product standards and are not covered by the present document.
NOTE 5: Where the present document is referenced by more specific standards or procedures, these should define
and name the relevant conditions to which this test procedure is applied.
1.2 Equipment not in the scope of the present document
The present document does not apply to the measurement of electrical power consumption in networked standby for
edge equipment. The edge equipment is a networked equipment that can be connected to a network and interact with
that network or other devices and that does not have, as its primary function, the passing of network traffic to provide a
network. Edge equipment are covered in EN 50643 [i.8].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 303 423 V1.3.1:2021
8 ETSI EN 303 423 V1.3.1 (2021-07)
The following referenced documents are necessary for the application of the present document.
[1] EN 50564:2011: "Electrical and electronic household and office equipment - measurement of low
power consumption", produced by CENELEC.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
[i.2] Commission Regulation (EU) No 801/2013 of 22 August 2013 amending Regulation (EC) No
1275/2008 with regard to ecodesign requirements for standby, off mode electric power
consumption of electrical and electronic household and office equipment, and amending
Regulation (EC) No 642/2009 with regard to ecodesign requirements for televisions.
[i.3] Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for no-load
condition electric power consumption and average active efficiency of external power supplies.
[i.4] ETSI EN 301 575 (05-2012): "Environmental Engineering (EE); Measurement method for energy
consumption of Customer Premises Equipment (CPE)".
[i.5] European Commission Directorate-General, Joint Research Centre: "Code Of Conduct on Energy
Consumption of Broadband Communication Equipment"; Final V5: 20 December 2013.
NOTE: Available at Broadband Communication Equipment Codes of Conduct | E3P (europa.eu).
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS® 2.0 Interface".
[i.7] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS® 3.0 Interface".
[i.8] EN 50643: "Electrical and electronic household and office equipment - Measurement of networked
standby power consumption of edge equipment", produced by CENELEC.
[i.9] IEC 60050: "International Electrotechnical Vocabulary".
[i.10] Commission Regulation (EC) No 642/2009 of 22 July 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for
televisions.
[i.11] IEC IEV ref 904-03-01: "Environmental standardization for electrical and electronic products and
systems".
NOTE: Available at http://www.electropedia.org/iev/iev.nsf/display?openform&ievref=904-03-01.
[i.12] IEEE 802.11™-2012: "IEEE Standard for Information technology -- Telecommunications and
information exchange between systems Local and metropolitan area networks -- Specific
requirements; Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications".
ETSI
---------------------- Page: 10 ----------------------
SIST EN 303 423 V1.3.1:2021
9 ETSI EN 303 423 V1.3.1 (2021-07)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in EN 50564 [1] and the following apply:
NOTE: When the present document is used to provide presumption of conformity to a European Directive or
Regulation, definitions given in the Directive or Regulation prevail.
edge equipment: networked equipment that can be connected to a network and interact with that network or other
equipment and that does not have, as its primary function, the passing of network traffic to provide a network
NOTE: Examples of edge equipment are given in Annex B.
interconnecting equipment: networked equipment that has, as its primary function, the passing of network traffic to
provide a network
NOTE: Examples of interconnecting equipment are given in Annex B.
logical network port: network technology running over a physical network port
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: Different communication protocols result in different network technologies.
low voltage external power supply: external power supply with a nameplate output voltage of less than 6 volts and a
nameplate output current greater than or equal to 550 milliamperes
NOTE: EC Commission Regulation No 278/2009 [i.3] definition.
network: communication infrastructure with a topology of links, an architecture, including the physical components,
organizational principles, communication procedures and formats (protocols)
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network availability: capability of the equipment to resume functions after a remotely initiated trigger has been
detected by a network port
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network port: wired or wireless physical interface of the network connection located on the equipment through which
the equipment can be remotely activated
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: The International Electrotechnical Vocabulary (IEC 60050 [i.9]) defines "port (of a network)" as:
"a termination through which signals can enter or leave a network".
networked equipment: equipment that can connect to a network and has one or more network ports
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
networked standby: condition in which the equipment is able to resume a function by way of a remotely initiated
trigger from a network connection
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
physical network port: physical (hardware) medium of a network port. A physical network port can host two or more
network technologies
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: A "physical network port" can consist of multiple "logical network ports".
ETSI
---------------------- Page: 11 ----------------------
SIST EN 303 423 V1.3.1:2021
10 ETSI EN 303 423 V1.3.1 (2021-07)
power management: automatic control mechanism that achieves the smallest input power consistent with a
pre-determined level of functionality
NOTE: Source: IEV 904-03-01 [i.11], modified by omission of the note to entry.
reactivation trigger: signal that brings the equipment back to active mode
NOTE: The reactivation may be remotely initiated.
remotely initiated trigger: signal that comes from outside the equipment via a network
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ADSL Asymmetric Digital Subscriber Line
ADSL2plus Second generation ADSL with extended bandwidth
AP Access Point
CRC Cyclic Redundancy Check
®
DOCSIS Data Over Cable Service Interface Specification
DSL Digital Subscriber Line
EFTA European Free Trade Association
EPON Ethernet Passive Optical Network
EUT Equipment Under Test
FXS Foreign eXchange Station
GPON Gigabyte Passive Optical Network
HiNA High Network Availability
HPNA Home Phoneline Networking Alliance
LAN Local Area Network
MoCA Multimedia over Coax Alliance
POF Plastic Optical Fibber
PSD Power Spectral Density
QAM Quadrature Amplitude Modulation
RF Radio Frequency
USB Universal Serial Bus
VDSL Very high speed Digital Subscriber Line
VDSL2 Second generation VDSL
WAN Wide Area Network
WiMAX Worldwide interoperability for Microwave Access
XG-PON 10-Gigabit-capable Passive Optical Network
4 Information required for testing purposes
4.1 Information about networked port(s)
For each type of physical and associated logical networked port, the following information shall be provided by the
manufacturer:
a) the default time after which the power management function, or a similar function, automatically switches the
equipment into networked standby, and if available, the procedure for:
1) setting a time shorter than the default time; and/or
ETSI
---------------------- Page: 12 ----------------------
SIST EN 303 423 V1.3.1:2021
11 E
...
ETSI EN 303 423 V1.3.1 (2021-07)
HARMONISED EUROPEAN STANDARD
Environmental Engineering (EE);
Electrical and electronic household and office equipment;
Measurement of networked standby power consumption of
Interconnecting equipment
---------------------- Page: 1 ----------------------
2 ETSI EN 303 423 V1.3.1 (2021-07)
Reference
REN/EE-007005
Keywords
customer premises networks, energy efficiency,
network, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 423 V1.3.1 (2021-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
1.1 Equipment in the scope of the present document . 7
1.2 Equipment not in the scope of the present document . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Information required for testing purposes . 10
4.1 Information about networked port(s) . 10
4.2 Power management function - periods & conditions . 11
4.3 Activation and deactivation of wireless network connections . 11
5 Measurement conditions. 11
5.1 Common requirements . 11
5.2 Test room. 12
5.3 Power supply . 12
5.4 Power measuring instruments. 12
5.5 Configuration of network ports . 12
5.6 Measurement uncertainty . 14
6 Measurement procedures . 15
6.1 General . 15
6.2 Wireless network port management . 15
6.2.0 General . 15
6.2.1 Test sequence . 15
6.2.2 Verifying that wireless connections are deactivated . 15
6.2.3 Verifying that wireless logical network port is active. 15
6.3 Preparation of the EUT and general testing aspects . 15
6.4 Power management, reactivation and networked standby power consumption . 16
6.5 Measurement of standby power consumption with all network ports disconnected . 17
6.6 Measurement of networked standby power consumption with all network ports connected . 17
7 Test report . 17
7.1 Test and laboratory details. 17
7.2 Details of product under test. 17
7.3 Test parameters and network configuration . 18
7.4 Measured and documented data . 18
Annex A (informative): Relationship between the present document and the ecodesign
requirements of Commission Regulation (EC) No 1275/2008, as
amended by Commission Regulation (EU) No 801/2013 . 19
Annex B (informative): Equipment classification . 22
B.1 General . 22
Annex C (informative): General information on network technologies and network
configurations with respect to power consumption . 24
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 423 V1.3.1 (2021-07)
C.1 Examples of network port configuration . 24
Annex D (informative): Information to be provided to the user and other interested parties . 25
D.1 Information to be provided to the user and other interested parties . 25
D.1.1 Information available on-line . 25
D.1.2 Information available in the user manual . 25
Annex E (informative): Example of a test report template . 26
Annex F (informative): Bibliography . 28
Annex G (informative): Change history . 29
History . 30
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 423 V1.3.1 (2021-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Environmental
Engineering (EE).
The present document has been prepared under the Commission's standardisation request M/544, C(2015) 9468 final of
5 January 2016, to the European standardisation organizations as regards ecodesign requirements for networked standby
in support of Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] (see note 2), to provide one
voluntary means of conforming to the ecodesign requirements on networked standby of the following:
• Commission Regulation (EC) No 1275/2008 [i.1] of 17 December 2008 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for standby and off
mode, and networked standby, electric power consumption of electrical and electronic household and office
equipment; and
• Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC of the
European Parliament and of the Council with regard to ecodesign requirements for televisions.
NOTE 1: Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] were amended by
Commission Regulation (EU) No 801/2013 [i.2] of 22 August 2013.
NOTE 2: Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for televisions is
quoted in the introduction of annex A, but no relationship with the present document and the requirements
of Commission Regulation (EC) No 642/2009 are provided because televisions are out of scope of the
present document.
Once the present document is cited in the Official Journal of the European Union under that Regulation, compliance
with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding ecodesign requirements of that Regulation and
associated EFTA Regulations.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 423 V1.3.1 (2021-07)
National transposition dates
Date of adoption of this EN: 29 June 2021
Date of latest announcement of this EN (doa): 30 September 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2022
Date of withdrawal of any conflicting National Standard (dow): 31 March 2023
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The methods defined in the present document are intended to define requirements for the measurement of the power
consumed by the interconnecting equipment having one or more wired or wireless networked port(s) able to resume a
function by way of a remotely initiated trigger or reactivation trigger from a network connection. The present document
also provides a method to test power management and whether it is possible to deactivate wireless network
connection(s).
For the measurement of low power modes, reference is made to EN 50564 [1].
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 423 V1.3.1 (2021-07)
1 Scope
1.1 Equipment in the scope of the present document
The present document specifies methods of measurement of electrical power consumption in networked standby and the
reporting of the results for network interconnecting equipment.
Example of interconnecting equipment are in Annex B.
Power consumption in standby (other than networked standby) is covered by EN 50564 [1], including the input voltage
range.
The present document also provides a method to test power management and whether it is possible to deactivate
wireless network connection(s).
The present document applies to electrical products with a rated input voltage of 230 V a.c. for single phase products
and 400 V a.c. for three phase products.
The present document is produced under the mandate M/544 and can be used to demonstrate compliance to the EU
Regulation (EC) No 1275/2008 [i.1] amended by Regulation (EU) 801/2013 [i.2].
The present document does not apply to televisions as defined in Regulation (EC) No 642/2009 [i.10].
NOTE 1: The EU regulation 801/2013 [i.2] applies to equipment designed for use with a nominal voltage rating of
250 V and below.
NOTE 2: EU regulation 801/2013 [i.2] does not apply to electrical and electronic household and office equipment
placed on the market with a low voltage external power supply to work as intended.
NOTE 3: "Low voltage external power supply" is the definition provided in EU regulation 278/2009 [i.3].
NOTE 4: The measurement of energy consumption and performance of equipment during intended use are
generally specified in product standards and are not covered by the present document.
NOTE 5: Where the present document is referenced by more specific standards or procedures, these should define
and name the relevant conditions to which this test procedure is applied.
1.2 Equipment not in the scope of the present document
The present document does not apply to the measurement of electrical power consumption in networked standby for
edge equipment. The edge equipment is a networked equipment that can be connected to a network and interact with
that network or other devices and that does not have, as its primary function, the passing of network traffic to provide a
network. Edge equipment are covered in EN 50643 [i.8].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 423 V1.3.1 (2021-07)
The following referenced documents are necessary for the application of the present document.
[1] EN 50564:2011: "Electrical and electronic household and office equipment - measurement of low
power consumption", produced by CENELEC.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
[i.2] Commission Regulation (EU) No 801/2013 of 22 August 2013 amending Regulation (EC) No
1275/2008 with regard to ecodesign requirements for standby, off mode electric power
consumption of electrical and electronic household and office equipment, and amending
Regulation (EC) No 642/2009 with regard to ecodesign requirements for televisions.
[i.3] Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for no-load
condition electric power consumption and average active efficiency of external power supplies.
[i.4] ETSI EN 301 575 (05-2012): "Environmental Engineering (EE); Measurement method for energy
consumption of Customer Premises Equipment (CPE)".
[i.5] European Commission Directorate-General, Joint Research Centre: "Code Of Conduct on Energy
Consumption of Broadband Communication Equipment"; Final V5: 20 December 2013.
NOTE: Available at Broadband Communication Equipment Codes of Conduct | E3P (europa.eu).
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS® 2.0 Interface".
[i.7] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS® 3.0 Interface".
[i.8] EN 50643: "Electrical and electronic household and office equipment - Measurement of networked
standby power consumption of edge equipment", produced by CENELEC.
[i.9] IEC 60050: "International Electrotechnical Vocabulary".
[i.10] Commission Regulation (EC) No 642/2009 of 22 July 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for
televisions.
[i.11] IEC IEV ref 904-03-01: "Environmental standardization for electrical and electronic products and
systems".
NOTE: Available at http://www.electropedia.org/iev/iev.nsf/display?openform&ievref=904-03-01.
[i.12] IEEE 802.11™-2012: "IEEE Standard for Information technology -- Telecommunications and
information exchange between systems Local and metropolitan area networks -- Specific
requirements; Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications".
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 303 423 V1.3.1 (2021-07)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in EN 50564 [1] and the following apply:
NOTE: When the present document is used to provide presumption of conformity to a European Directive or
Regulation, definitions given in the Directive or Regulation prevail.
edge equipment: networked equipment that can be connected to a network and interact with that network or other
equipment and that does not have, as its primary function, the passing of network traffic to provide a network
NOTE: Examples of edge equipment are given in Annex B.
interconnecting equipment: networked equipment that has, as its primary function, the passing of network traffic to
provide a network
NOTE: Examples of interconnecting equipment are given in Annex B.
logical network port: network technology running over a physical network port
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: Different communication protocols result in different network technologies.
low voltage external power supply: external power supply with a nameplate output voltage of less than 6 volts and a
nameplate output current greater than or equal to 550 milliamperes
NOTE: EC Commission Regulation No 278/2009 [i.3] definition.
network: communication infrastructure with a topology of links, an architecture, including the physical components,
organizational principles, communication procedures and formats (protocols)
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network availability: capability of the equipment to resume functions after a remotely initiated trigger has been
detected by a network port
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network port: wired or wireless physical interface of the network connection located on the equipment through which
the equipment can be remotely activated
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: The International Electrotechnical Vocabulary (IEC 60050 [i.9]) defines "port (of a network)" as:
"a termination through which signals can enter or leave a network".
networked equipment: equipment that can connect to a network and has one or more network ports
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
networked standby: condition in which the equipment is able to resume a function by way of a remotely initiated
trigger from a network connection
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
physical network port: physical (hardware) medium of a network port. A physical network port can host two or more
network technologies
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: A "physical network port" can consist of multiple "logical network ports".
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 303 423 V1.3.1 (2021-07)
power management: automatic control mechanism that achieves the smallest input power consistent with a
pre-determined level of functionality
NOTE: Source: IEV 904-03-01 [i.11], modified by omission of the note to entry.
reactivation trigger: signal that brings the equipment back to active mode
NOTE: The reactivation may be remotely initiated.
remotely initiated trigger: signal that comes from outside the equipment via a network
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ADSL Asymmetric Digital Subscriber Line
ADSL2plus Second generation ADSL with extended bandwidth
AP Access Point
CRC Cyclic Redundancy Check
®
DOCSIS Data Over Cable Service Interface Specification
DSL Digital Subscriber Line
EFTA European Free Trade Association
EPON Ethernet Passive Optical Network
EUT Equipment Under Test
FXS Foreign eXchange Station
GPON Gigabyte Passive Optical Network
HiNA High Network Availability
HPNA Home Phoneline Networking Alliance
LAN Local Area Network
MoCA Multimedia over Coax Alliance
POF Plastic Optical Fibber
PSD Power Spectral Density
QAM Quadrature Amplitude Modulation
RF Radio Frequency
USB Universal Serial Bus
VDSL Very high speed Digital Subscriber Line
VDSL2 Second generation VDSL
WAN Wide Area Network
WiMAX Worldwide interoperability for Microwave Access
XG-PON 10-Gigabit-capable Passive Optical Network
4 Information required for testing purposes
4.1 Information about networked port(s)
For each type of physical and associated logical networked port, the following information shall be provided by the
manufacturer:
a) the default time after which the power management function, or a similar function, automatically switches the
equipment into networked standby, and if available, the procedure for:
1) setting a time shorter than the default time; and/or
ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 303 423 V1.3.1 (2021-07)
2) manually switching the equipment into networked standby;
b) the characteristics of the reactivation trigger (message, signal, etc.) that is used to reactivate the equipment
when in networked standby and how to remotely initiate it;
c) the maximum performance specifications, e.g. the maximum speed or data rate supported by that networked
port;
d) the (maximum) power consumption of the equipment in a condition providing networked standby into which
power management function, or a similar function, will switch the equipment, if only this port is used for
remote activation, e.g. the declared power consumption of the equipment under defined conditions for a type
of port;
e) the communication protocol used by equipment;
f) the radio frequency range at which each radio wireless logical network port operates;
g) the characteristics of wireless logical network ports other than radio wireless logical network ports.
NOTE: Annex D describes examples of product information for network equipment.
4.2 Power management function - periods & conditions
The manufacturer shall provide information on:
• whether the equipment under test provides a power management or a similar function. If the EUT does not
provide power management or a similar function, the manuf
...
Final draft ETSI EN 303 423 V1.3.0 (2021-04)
HARMONISED EUROPEAN STANDARD
Environmental Engineering (EE);
Electrical and electronic household and office equipment;
Measurement of networked standby power consumption of
Interconnecting equipment
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
Reference
REN/EE-007005
Keywords
customer premises networks, energy efficiency,
network, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
1.1 Equipment in the scope of the present document . 7
1.2 Equipment not in the scope of the present document . . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Information required for testing purposes . 10
4.1 Information about networked port(s) . 10
4.2 Power management function - periods & conditions . 11
4.3 Activation and deactivation of wireless network connections . 11
5 Measurement conditions. 11
5.1 Common requirements . 11
5.2 Test room. 12
5.3 Power supply . 12
5.4 Power measuring instruments. 12
5.5 Configuration of network ports . 12
5.6 Measurement uncertainty . 14
6 Measurement procedures . 15
6.1 General . 15
6.2 Wireless network port management . 15
6.2.0 General . 15
6.2.1 Test sequence . 15
6.2.2 Verifying that wireless connections are deactivated . 15
6.2.3 Verifying that wireless logical network port is active. 15
6.3 Preparation of the EUT and general testing aspects . 15
6.4 Power management, reactivation and networked standby power consumption . 16
6.5 Measurement of standby power consumption with all network ports disconnected . 17
6.6 Measurement of networked standby power consumption with all network ports connected . 17
7 Test report . 17
7.1 Test and laboratory details. 17
7.2 Details of product under test. 17
7.3 Test parameters and network configuration . 18
7.4 Measured and documented data . 18
Annex A (informative): Relationship between the present document and the ecodesign
requirements of Commission Regulation (EC) No 1275/2008, as
amended by Commission Regulation (EU) No 801/2013 . 19
Annex B (informative): Equipment classification . 22
B.1 General . 22
Annex C (informative): General information on network technologies and network
configurations with respect to power consumption . 24
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
C.1 Examples of network port configuration . 24
Annex D (informative): Information to be provided to the user and other interested parties . 25
D.1 Information to be provided to the user and other interested parties . 25
D.1.1 Information available on-line . 25
D.1.2 Information available in the user manual . 25
Annex E (informative): Example of a test report template . 26
Annex F (informative): Bibliography . 28
Annex G (informative): Change history . 29
History . 30
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Environmental
Engineering (EE), and is now submitted for the Vote phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request M/544, C(2015) 9468 final of
5 January 2016, to the European standardisation organizations as regards ecodesign requirements for networked standby
in support of Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] (see note 2), to provide one
voluntary means of conforming to the ecodesign requirements on networked standby of the following:
• Commission Regulation (EC) No 1275/2008 [i.1] of 17 December 2008 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for standby and off
mode, and networked standby, electric power consumption of electrical and electronic household and office
equipment; and
• Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC of the
European Parliament and of the Council with regard to ecodesign requirements for televisions.
NOTE 1: Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] were amended by
Commission Regulation (EU) No 801/2013 [i.2] of 22 August 2013.
NOTE 2: Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for televisions is
quoted in the introduction of annex A, but no relationship with the present document and the requirements
of Commission Regulation (EC) No 642/2009 are provided because televisions are out of scope of the
present document.
Once the present document is cited in the Official Journal of the European Union under that Regulation, compliance
with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding ecodesign requirements of that Regulation and
associated EFTA Regulations.
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The methods defined in the present document are intended to define requirements for the measurement of the power
consumed by the interconnecting equipment having one or more wired or wireless networked port(s) able to resume a
function by way of a remotely initiated trigger or reactivation trigger from a network connection. The present document
also provides a method to test power management and whether it is possible to deactivate wireless network
connection(s).
For the measurement of low power modes, reference is made to EN 50564 [1].
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
1 Scope
1.1 Equipment in the scope of the present document
The present document specifies methods of measurement of electrical power consumption in networked standby and the
reporting of the results for network interconnecting equipment.
Example of interconnecting equipment are in Annex B.
Power consumption in standby (other than networked standby) is covered by EN 50564 [1], including the input voltage
range.
The present document also provides a method to test power management and whether it is possible to deactivate
wireless network connection(s).
The present document applies to electrical products with a rated input voltage of 230 V a.c. for single phase products
and 400 V a.c. for three phase products.
The present document is produced under the mandate M/544 and can be used to demonstrate compliance to the EU
Regulation (EC) No 1275/2008 [i.1] amended by Regulation 801/2013 [i.2].
The present document does not apply to televisions as defined in Regulation (EC) No 642/2009 [i.10].
NOTE 1: The EU regulation 801/2013 [i.2] applies to equipment designed for use with a nominal voltage rating of
250 V and below.
NOTE 2: EU regulation 801/2013 [i.2] does not apply to electrical and electronic household and office equipment
placed on the market with a low voltage external power supply to work as intended.
NOTE 3: "Low voltage external power supply" is the definition provided in EU regulation 278/2009 [i.3].
NOTE 4: The measurement of energy consumption and performance of equipment during intended use are
generally specified in product standards and are not covered by the present document.
NOTE 5: Where the present document is referenced by more specific standards or procedures, these should define
and name the relevant conditions to which this test procedure is applied.
1.2 Equipment not in the scope of the present document
The present document does not apply to the measurement of electrical power consumption in networked standby for
edge equipment. The edge equipment is a networked equipment that can be connected to a network and interact with
that network or other devices and that does not have, as its primary function, the passing of network traffic to provide a
network. Edge equipment are covered in EN 50643 [i.8].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
The following referenced documents are necessary for the application of the present document.
[1] EN 50564:2011: "Electrical and electronic household and office equipment - measurement of low
power consumption", produced by CENELEC.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
[i.2] Commission Regulation (EU) No 801/2013 of 22 August 2013 amending Regulation (EC) No
1275/2008 with regard to ecodesign requirements for standby, off mode electric power
consumption of electrical and electronic household and office equipment, and amending
Regulation (EC) No 642/2009 with regard to ecodesign requirements for televisions.
[i.3] Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for no-load
condition electric power consumption and average active efficiency of external power supplies.
[i.4] ETSI EN 301 575 (05-2012): "Environmental Engineering (EE); Measurement method for energy
consumption of Customer Premises Equipment (CPE)".
[i.5] European Commission Directorate-General, Joint Research Centre: "Code Of Conduct on Energy
Consumption of Broadband Communication Equipment"; Final V5: 20 December 2013.
NOTE: Available at Broadband Communication Equipment Codes of Conduct | E3P (europa.eu).
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS® 2.0 Interface".
[i.7] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS® 3.0 Interface".
[i.8] EN 50643: "Electrical and electronic household and office equipment - Measurement of networked
standby power consumption of edge equipment", produced by CENELEC.
[i.9] IEC 60050: "International Electrotechnical Vocabulary".
[i.10] Commission Regulation (EC) No 642/2009 of 22 July 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for
televisions.
[i.11] IEC IEV ref 904-03-01: "Environmental standardization for electrical and electronic products and
systems".
NOTE: Available at http://www.electropedia.org/iev/iev.nsf/display?openform&ievref=904-03-01.
[i.12] IEEE 802.11™-2012: "IEEE Standard for Information technology -- Telecommunications and
information exchange between systems Local and metropolitan area networks -- Specific
requirements; Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications".
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in EN 50564 [1] and the following apply:
NOTE: When the present document is used to provide presumption of conformity to a European Directive or
Regulation, definitions given in the Directive or Regulation prevail.
edge equipment: networked equipment that can be connected to a network and interact with that network or other
equipment and that does not have, as its primary function, the passing of network traffic to provide a network
NOTE: Examples of edge equipment are given in Annex B.
interconnecting equipment: networked equipment that has, as its primary function, the passing of network traffic to
provide a network
NOTE: Examples of interconnecting equipment are given in Annex B.
logical network port: network technology running over a physical network port
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: Different communication protocols result in different network technologies.
low voltage external power supply: external power supply with a nameplate output voltage of less than 6 volts and a
nameplate output current greater than or equal to 550 milliamperes
NOTE: EC Commission Regulation No 278/2009 [i.3] definition.
network: communication infrastructure with a topology of links, an architecture, including the physical components,
organizational principles, communication procedures and formats (protocols)
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network availability: capability of the equipment to resume functions after a remotely initiated trigger has been
detected by a network port
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network port: wired or wireless physical interface of the network connection located on the equipment through which
the equipment can be remotely activated
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: The International Electrotechnical Vocabulary (IEC 60050 [i.9]) defines "port (of a network)" as:
"a termination through which signals can enter or leave a network".
networked equipment: equipment that can connect to a network and has one or more network ports
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
networked standby: condition in which the equipment is able to resume a function by way of a remotely initiated
trigger from a network connection
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
physical network port: physical (hardware) medium of a network port. A physical network port can host two or more
network technologies
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: A "physical network port" can consist of multiple "logical network ports".
ETSI
---------------------- Page: 9 ----------------------
10 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
power management: automatic control mechanism that achieves the smallest input power consistent with a
pre-determined level of functionality
NOTE: Source: IEV 904-03-01 [i.11], modified by omission of the note to entry.
reactivation trigger: signal that brings the equipment back to active mode
NOTE: The reactivation may be remotely initiated.
remotely initiated trigger: signal that comes from outside the equipment via a network
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ADSL Asymmetric Digital Subscriber Line
ADSL2plus Second generation ADSL with extended bandwidth
AP Access Point
CRC Cyclic Redundancy Check
®
DOCSIS Data Over Cable Service Interface Specification
DSL Digital Subscriber Line
EFTA European Free Trade Association
EPON Ethernet Passive Optical Network
EUT Equipment Under Test
FXS Foreign eXchange Station
GPON Gigabyte Passive Optical Network
HiNA High Network Availability
HPNA Home Phoneline Networking Alliance
LAN Local Area Network
MoCA Multimedia over Coax Alliance
POF Plastic Optical Fibber
PSD Power Spectral Density
QAM Quadrature Amplitude Modulation
RF Radio Frequency
USB Universal Serial Bus
VDSL Very high speed Digital Subscriber Line
VDSL2 Second generation VDSL
WAN Wide Area Network
WiMAX Worldwide interoperability for Microwave Access
XG-PON 10-Gigabit-capable Passive Optical Network
4 Information required for testing purposes
4.1 Information about networked port(s)
For each type of physical and associated logical networked port, the following information shall be provided by the
manufacturer:
a) the default time after which the power management function, or a similar function, automatically switches the
equipment into networked standby, and if available, the procedure for:
1) setting a time shorter than the default time; and/or
ETSI
---------------------- Page: 10 ----------------------
11 Final draft ETSI EN 303 423 V1.3.0 (2021-04)
2) manually switching the equipment into networked standby;
b) the characteristics of the reactivation trigger (message, signal, etc.) that is used to reactivate the equipment
when in networked standby and how to remotely initiate it;
c) the maximum performance specifications, e.g. the maximum speed or data rate supported by that networked
port;
d) the (maximum) power consumption of the equipment in a condition providing networked standby into which
power management function, or a similar function, will switch the equipment, if only this port is used for
remote activation, e.g. the declared power consumption of the equipment under defined conditions for a type
of port;
e) the communication protocol used by equipment;
f) the radio frequency range at which each radio wireless logical network port operates;
g) the characteristics of wireless logical network ports other than radio wireless logical network ports.
NOTE: Annex D describes examples of product information for network equipment.
4.2 Power management function - periods & conditions
The m
...
Draft ETSI EN 303 423 V1.2.9 (2020-03)
HARMONISED EUROPEAN STANDARD
Environmental Engineering (EE);
Electrical and electronic household and office equipment;
Measurement of networked standby power consumption of
Interconnecting equipment
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 423 V1.2.9 (2020-03)
Reference
REN/EE-007005
Keywords
customer premises networks, energy efficiency,
network, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 423 V1.2.9 (2020-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
1.1 Equipment in the scope of the present document . 7
1.2 Equipment not in the scope of the present document . . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Information required for testing purposes . 10
4.1 Information about networked port(s) . 10
4.2 Power management function - periods & conditions . 11
4.3 Activation and deactivation of wireless network connections . 11
5 Measurement conditions. 11
5.1 Common requirements . 11
5.2 Test room. 12
5.3 Power supply . 12
5.4 Power measuring instruments. 12
5.5 Configuration of network ports . 12
5.6 Measurement uncertainty . 14
6 Measurement procedures . 14
6.1 General . 14
6.2 Wireless network port management . 15
6.2.0 General . 15
6.2.1 Test sequence . 15
6.2.2 Verifying that wireless connections are deactivated . 15
6.2.3 Verifying that wireless logical network port is active. 15
6.3 Preparation of the EUT and general testing aspects . 15
6.4 Power management, reactivation and networked standby power consumption . 15
6.5 Measurement of standby power consumption with all network ports disconnected . 16
6.6 Measurement of networked standby power consumption with all network ports connected . 17
7 Test report . 17
7.1 Test and laboratory details. 17
7.2 Details of product under test. 17
7.3 Test parameters and network configuration . 17
7.4 Measured and documented data . 18
Annex A (informative): Relationship between the present document and the ecodesign
requirements of Commission Regulation (EC) No 1275/2008, as
amended by Commission Regulation (EU) No 801/2013 . 19
Annex B (informative): Equipment classification . 22
B.1 General . 22
Annex C (informative): General information on network technologies and network
configurations with respect to power consumption . 24
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 423 V1.2.9 (2020-03)
C.1 Examples of network port configuration . 24
Annex D (informative): Information to be provided to the user and other interested parties . 25
D.1 Information to be provided to the user and other interested parties . 25
D.1.1 Information available on-line . 25
D.1.2 Information available in the user manual . 25
Annex E (informative): Example of a test report template . 26
Annex F (informative): Bibliography . 28
Annex G (informative): Change history . 29
History . 30
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 423 V1.2.9 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Environmental
Engineering (EE), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document has been prepared under the Commission's standardisation M/544, C(2015) 9468 final of
5 January 2016, as regards ecodesign requirements for networked standby in support of Regulation (EC)
No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10], to provide one voluntary means of conforming to the
ecodesign requirements on networked standby of the following:
• Commission Regulation (EC) No 1275/2008 [i.1] of 17 December 2008 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for standby and off
mode, and networked standby, electric power consumption of electrical and electronic household and office
equipment; and
• Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC of the
European Parliament and of the Council with regard to ecodesign requirements for televisions.
NOTE 1: Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] were amended by
Commission Regulation (EU) No 801/2013 [i.2] of 22 August 2013.
NOTE 2: Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for televisions is
quoted in the introduction of this annex but no relationship with this standard and the requirements of
Commission Regulation (EC) No 642/2009 [i.10] are provided because televisions are out of scope of this
standard.
Once the present document is cited in the Official Journal of the European Union under that Regulation, compliance
with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding ecodesign requirements of that Regulation and
associated EFTA Regulations.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 423 V1.2.9 (2020-03)
National transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The methods defined in the present document are intended to define requirements for the measurement of the power
consumed by the interconnecting equipment having one or more wired or wireless networked port(s) able to resume a
function by way of a remotely initiated trigger or reactivation trigger from a network connection. The present document
also provides a method to test power management and whether it is possible to deactivate wireless network
connection(s).
For the measurement of low power modes, reference is made to CENELEC EN 50564 [1].
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 423 V1.2.9 (2020-03)
1 Scope
1.1 Equipment in the scope of the present document
The present document specifies methods of measurement of electrical power consumption in networked standby and the
reporting of the results for network interconnecting equipment.
Example of interconnecting equipment are in Annex B.
Power consumption in standby (other than networked standby) is covered by CENELEC EN 50564 [1], including the
input voltage range.
The present document also provides a method to test power management and whether it is possible to deactivate
wireless network connection(s).
The present document applies to electrical products with a rated input voltage of 230 V a.c. for single phase products
and 400 V a.c. for three phase products.
The present document is produced under the mandate M/544 and can be used to demonstrate compliance to the EU
Regulation (EC) No 1275/2008 [i.1] amended by Regulation 801/2013 [i.2].
The present document does not apply to televisions as defined in Regulation (EC) No 642/2009 [i.10].
NOTE 1: The EU regulation 801/2013 [i.2] applies to equipment designed for use with a nominal voltage rating of
250 V and below.
NOTE 2: EU regulation 801/2013 [i.2] does not apply to electrical and electronic household and office equipment
placed on the market with a low voltage external power supply to work as intended.
NOTE 3: "Low voltage external power supply" is the definition provided in EU regulation 278/2009 [i.3].
NOTE 4: The measurement of energy consumption and performance of equipment during intended use are
generally specified in product standards and are not covered by the present document.
NOTE 5: Where the present document is referenced by more specific standards or procedures, these should define
and name the relevant conditions to which this test procedure is applied.
1.2 Equipment not in the scope of the present document
The present document does not apply to the measurement of electrical power consumption in networked standby for
edge equipment. The edge equipment is a networked equipment that can be connected to a network and interact with
that network or other devices and that does not have, as its primary function, the passing of network traffic to provide a
network. Edge equipment are covered in CENELEC EN 50643 [i.8].
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 423 V1.2.9 (2020-03)
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 50564:2011: "Electrical and electronic household and office equipment -
measurement of low power consumption".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
[i.2] Commission Regulation (EU) No 801/2013 of 22 August 2013 amending Regulation (EC)
No 1275/2008 with regard to ecodesign requirements for standby, off mode electric power
consumption of electrical and electronic household and office equipment, and amending
Regulation (EC) No 642/2009 with regard to ecodesign requirements for televisions.
[i.3] Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for no-load
condition electric power consumption and average active efficiency of external power supplies.
[i.4] ETSI EN 301 575 (05-2012): "Environmental Engineering (EE); Measurement method for energy
consumption of Customer Premises Equipment (CPE)".
[i.5] European Commission Directorate-General, Joint Research Centre: "Code Of Conduct on Energy
Consumption of Broadband Communication Equipment"; Final V5: 20 December 2013.
NOTE: Available at
http://iet.jrc.ec.europa.eu/energyefficiency/sites/energyefficiency/files/files/documents/ICT_CoC/cocv5-
broadband_final.pdf.
®
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS 2.0 Interface".
®
[i.7] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS 3.0 Interface".
[i.8] CENELEC EN 50643: "Electrical and electronic household and office equipment - Measurement
of networked standby power consumption of edge equipment".
[i.9] IEC 60050: "International Electrotechnical Vocabulary".
[i.10] Commission Regulation (EC) No 642/2009 of 22 July 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for
televisions.
[i.11] IEC IEV ref 904-03-01: "Environmental standardization for electrical and electronic products and
systems".
NOTE: Available at http://www.electropedia.org/iev/iev.nsf/display?openform&ievref=904-03-01.
[i.12] IEEE 802.11™-2012: "IEEE Standard for Information technology -- Telecommunications and
information exchange between systems Local and metropolitan area networks -- Specific
requirements; Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications".
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 303 423 V1.2.9 (2020-03)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in CENELEC EN 50564 [1] and the following apply:
NOTE: When the present document is used to provide presumption of conformity to a European Directive or
Regulation, definitions given in the Directive or Regulation prevail.
edge equipment: networked equipment that can be connected to a network and interact with that network or other
equipment and that does not have, as its primary function, the passing of network traffic to provide a network
NOTE: Examples of edge equipment are given in Annex B.
interconnecting equipment: networked equipment that has, as its primary function, the passing of network traffic to
provide a network
NOTE: Examples of interconnecting equipment are given in Annex B.
logical network port: network technology running over a physical network port
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: Different communication protocols result in different network technologies.
low voltage external power supply: external power supply with a nameplate output voltage of less than 6 volts and a
nameplate output current greater than or equal to 550 milliamperes
NOTE: EC Commission Regulation No 278/2009 [i.3] definition.
network: communication infrastructure with a topology of links, an architecture, including the physical components,
organizational principles, communication procedures and formats (protocols)
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network availability: capability of the equipment to resume functions after a remotely initiated trigger has been
detected by a network port
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network port: wired or wireless physical interface of the network connection located on the equipment through which
the equipment can be remotely activated
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: The International Electrotechnical Vocabulary (IEC 60050 [i.9]) defines "port (of a network)" as:
"a termination through which signals can enter or leave a network".
networked equipment: equipment that can connect to a network and has one or more network ports
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
networked standby: condition in which the equipment is able to resume a function by way of a remotely initiated
trigger from a network connection
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
physical network port: physical (hardware) medium of a network port. A physical network port can host two or more
network technologies
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: A "physical network port" can consist of multiple "logical network ports".
ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 303 423 V1.2.9 (2020-03)
power management: automatic control mechanism that achieves the smallest input power consistent with a
pre-determined level of functionality
NOTE: Source: IEV 904-03-01 [i.11], modified by omission of the note to entry.
reactivation trigger: signal that brings the equipment back to active mode
NOTE: The reactivation may be remotely initiated.
remotely initiated trigger: signal that comes from outside the equipment via a network
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ADSL Asymmetric Digital Subscriber Line
ADSL2plus Second generation ADSL with extended bandwidth
AP Access Point
CRC Cyclic Redundancy Check
®
DOCSIS Data Over Cable Service Interface Specification
DSL Digital Subscriber Line
EFTA European Free Trade Association
EPON Ethernet Passive Optical Network
EUT Equipment Under Test
FXS Foreign eXchange Station
GPON Gigabyte Passive Optical Network
HiNA High Network Availability
HPNA Home Phoneline Networking Alliance
LAN Local Area Network
POF Plastic Optical Fibber
PSD Power Spectral Density
QAM Quadrature Amplitude Modulation
RF Radio Frequency
USB Universal Serial Bus
VDSL Very high speed Digital Subscriber Line
VDSL2 Second generation VDSL
WAN Wide Area Network
WiMAX Worldwide interoperability for Microwave Access
XG-PON 10-Gigabit-capable Passive Optical Network
4 Information required for testing purposes
4.1 Information about networked port(s)
For each type of physical and associated logical networked port, the following information shall be provided by the
manufacturer:
a) the default time after which the power management function, or a similar function, automatically switches the
equipment into networked standby, and if available, the procedure for:
1) setting a time shorter than the default time; and/or
2) manually switching the equipment into networked standby.
ETSI
---------------------- Page: 10 ----------------------
11 Draft ETSI EN 303 423 V1.2.9 (2020-03)
b) the characteristics of the reactivation trigger (message, signal, etc.) that is used to reactivate the equipment
when in networked standby and how to remotely initiate it;
c) the maximum performance specifications, e.g. the maximum speed or data rate supported by that networked
port;
d) the (maximum) power consumption of the equipment in a condition providing networked standby into which
power management function, or a similar function, will switch the equipment, if only this port is used for
remote activation, e.g. the declared power consumption of the equipment under defined conditions for a type
of port;
e) the communication protocol used by equipment;
f) the radio frequency range at which each radio wireless logical network port operates;
g) the characteristics of wireless logical network ports other than radio wireless logical network ports.
NOTE: Annex D describes examples of product information for network equipment.
4.2 Power management function - periods & conditions
The manufacturer shall provide information on:
• whether the equipment under test provides a power management or a similar function. If the EUT does not
provide power management or a similar function, the manufacturer shall indicate why such a function would
be inappropriate for the intended use;
• the default period of time after which the power management function, or a similar function, switches the
equipment automatically into a condition providing networked standby.
NOTE: According to European Regulation No 1275/2008 [i.1] (as amended by EU Regulation
No 801/2013 [i.2]), the maximum default period is given as 20 minutes during which the equipment has
not been providing its main function.
4.3 Activation and deactivation of wireless network connections
The manufacturer shall provide information on the procedure the user needs to follow in order to activate and deactivate
each wireless network connection, if any.
The above requirement does not apply to equipment which relies on a single wireless network connection for intended
use and does not have a wired network connection.
5 Measurement conditions
5.1 Common requirements
The general conditions for measurements specified in clause 4.1 of CENELEC EN 50564 [1] shall apply.
The tests described in clause 6 of the present document shall be repeated, if applicable, for each type of network port.
Each typ
...
SLOVENSKI STANDARD
oSIST prEN 303 423 V1.2.9:2020
01-junij-2020
Okoljski inženiring (EE) - Električna in elektronska gospodinjska in pisarniška
oprema - Meritve porabe energije povezovalne opreme v omrežni pripravljenosti
Environmental Engineering (EE) - Electrical and electronic household and office
equipment - Measurement of networked standby power consumption of Interconnecting
equipment
Ta slovenski standard je istoveten z: ETSI EN 303 423 V1.2.9 (2020-03)
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
27.015 Energijska učinkovitost. Energy efficiency. Energy
Ohranjanje energije na conservation in general
splošno
35.260 Pisarniški stroji Office machines
oSIST prEN 303 423 V1.2.9:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 423 V1.2.9:2020
---------------------- Page: 2 ----------------------
oSIST prEN 303 423 V1.2.9:2020
Draft ETSI EN 303 423 V1.2.9 (2020-03)
HARMONISED EUROPEAN STANDARD
Environmental Engineering (EE);
Electrical and electronic household and office equipment;
Measurement of networked standby power consumption of
Interconnecting equipment
---------------------- Page: 3 ----------------------
oSIST prEN 303 423 V1.2.9:2020
2 Draft ETSI EN 303 423 V1.2.9 (2020-03)
Reference
REN/EE-007005
Keywords
customer premises networks, energy efficiency,
network, power measurement
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 423 V1.2.9:2020
3 Draft ETSI EN 303 423 V1.2.9 (2020-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
1.1 Equipment in the scope of the present document . 7
1.2 Equipment not in the scope of the present document . . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Information required for testing purposes . 10
4.1 Information about networked port(s) . 10
4.2 Power management function - periods & conditions . 11
4.3 Activation and deactivation of wireless network connections . 11
5 Measurement conditions. 11
5.1 Common requirements . 11
5.2 Test room. 12
5.3 Power supply . 12
5.4 Power measuring instruments. 12
5.5 Configuration of network ports . 12
5.6 Measurement uncertainty . 14
6 Measurement procedures . 14
6.1 General . 14
6.2 Wireless network port management . 15
6.2.0 General . 15
6.2.1 Test sequence . 15
6.2.2 Verifying that wireless connections are deactivated . 15
6.2.3 Verifying that wireless logical network port is active. 15
6.3 Preparation of the EUT and general testing aspects . 15
6.4 Power management, reactivation and networked standby power consumption . 15
6.5 Measurement of standby power consumption with all network ports disconnected . 16
6.6 Measurement of networked standby power consumption with all network ports connected . 17
7 Test report . 17
7.1 Test and laboratory details. 17
7.2 Details of product under test. 17
7.3 Test parameters and network configuration . 17
7.4 Measured and documented data . 18
Annex A (informative): Relationship between the present document and the ecodesign
requirements of Commission Regulation (EC) No 1275/2008, as
amended by Commission Regulation (EU) No 801/2013 . 19
Annex B (informative): Equipment classification . 22
B.1 General . 22
Annex C (informative): General information on network technologies and network
configurations with respect to power consumption . 24
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 423 V1.2.9:2020
4 Draft ETSI EN 303 423 V1.2.9 (2020-03)
C.1 Examples of network port configuration . 24
Annex D (informative): Information to be provided to the user and other interested parties . 25
D.1 Information to be provided to the user and other interested parties . 25
D.1.1 Information available on-line . 25
D.1.2 Information available in the user manual . 25
Annex E (informative): Example of a test report template . 26
Annex F (informative): Bibliography . 28
Annex G (informative): Change history . 29
History . 30
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 423 V1.2.9:2020
5 Draft ETSI EN 303 423 V1.2.9 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Environmental
Engineering (EE), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document has been prepared under the Commission's standardisation M/544, C(2015) 9468 final of
5 January 2016, as regards ecodesign requirements for networked standby in support of Regulation (EC)
No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10], to provide one voluntary means of conforming to the
ecodesign requirements on networked standby of the following:
• Commission Regulation (EC) No 1275/2008 [i.1] of 17 December 2008 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for standby and off
mode, and networked standby, electric power consumption of electrical and electronic household and office
equipment; and
• Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC of the
European Parliament and of the Council with regard to ecodesign requirements for televisions.
NOTE 1: Regulation (EC) No 1275/2008 [i.1] and Regulation (EC) No 642/2009 [i.10] were amended by
Commission Regulation (EU) No 801/2013 [i.2] of 22 August 2013.
NOTE 2: Commission Regulation (EC) No 642/2009 [i.10] of 22 July 2009, implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for televisions is
quoted in the introduction of this annex but no relationship with this standard and the requirements of
Commission Regulation (EC) No 642/2009 [i.10] are provided because televisions are out of scope of this
standard.
Once the present document is cited in the Official Journal of the European Union under that Regulation, compliance
with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the
present document, a presumption of conformity with the corresponding ecodesign requirements of that Regulation and
associated EFTA Regulations.
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 303 423 V1.2.9:2020
6 Draft ETSI EN 303 423 V1.2.9 (2020-03)
National transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The methods defined in the present document are intended to define requirements for the measurement of the power
consumed by the interconnecting equipment having one or more wired or wireless networked port(s) able to resume a
function by way of a remotely initiated trigger or reactivation trigger from a network connection. The present document
also provides a method to test power management and whether it is possible to deactivate wireless network
connection(s).
For the measurement of low power modes, reference is made to CENELEC EN 50564 [1].
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 303 423 V1.2.9:2020
7 Draft ETSI EN 303 423 V1.2.9 (2020-03)
1 Scope
1.1 Equipment in the scope of the present document
The present document specifies methods of measurement of electrical power consumption in networked standby and the
reporting of the results for network interconnecting equipment.
Example of interconnecting equipment are in Annex B.
Power consumption in standby (other than networked standby) is covered by CENELEC EN 50564 [1], including the
input voltage range.
The present document also provides a method to test power management and whether it is possible to deactivate
wireless network connection(s).
The present document applies to electrical products with a rated input voltage of 230 V a.c. for single phase products
and 400 V a.c. for three phase products.
The present document is produced under the mandate M/544 and can be used to demonstrate compliance to the EU
Regulation (EC) No 1275/2008 [i.1] amended by Regulation 801/2013 [i.2].
The present document does not apply to televisions as defined in Regulation (EC) No 642/2009 [i.10].
NOTE 1: The EU regulation 801/2013 [i.2] applies to equipment designed for use with a nominal voltage rating of
250 V and below.
NOTE 2: EU regulation 801/2013 [i.2] does not apply to electrical and electronic household and office equipment
placed on the market with a low voltage external power supply to work as intended.
NOTE 3: "Low voltage external power supply" is the definition provided in EU regulation 278/2009 [i.3].
NOTE 4: The measurement of energy consumption and performance of equipment during intended use are
generally specified in product standards and are not covered by the present document.
NOTE 5: Where the present document is referenced by more specific standards or procedures, these should define
and name the relevant conditions to which this test procedure is applied.
1.2 Equipment not in the scope of the present document
The present document does not apply to the measurement of electrical power consumption in networked standby for
edge equipment. The edge equipment is a networked equipment that can be connected to a network and interact with
that network or other devices and that does not have, as its primary function, the passing of network traffic to provide a
network. Edge equipment are covered in CENELEC EN 50643 [i.8].
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 303 423 V1.2.9:2020
8 Draft ETSI EN 303 423 V1.2.9 (2020-03)
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 50564:2011: "Electrical and electronic household and office equipment -
measurement of low power consumption".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Commission Regulation (EC) No 1275/2008 of 17 December 2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements
for standby and off mode electric power consumption of electrical and electronic household and
office equipment.
[i.2] Commission Regulation (EU) No 801/2013 of 22 August 2013 amending Regulation (EC)
No 1275/2008 with regard to ecodesign requirements for standby, off mode electric power
consumption of electrical and electronic household and office equipment, and amending
Regulation (EC) No 642/2009 with regard to ecodesign requirements for televisions.
[i.3] Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for no-load
condition electric power consumption and average active efficiency of external power supplies.
[i.4] ETSI EN 301 575 (05-2012): "Environmental Engineering (EE); Measurement method for energy
consumption of Customer Premises Equipment (CPE)".
[i.5] European Commission Directorate-General, Joint Research Centre: "Code Of Conduct on Energy
Consumption of Broadband Communication Equipment"; Final V5: 20 December 2013.
NOTE: Available at
http://iet.jrc.ec.europa.eu/energyefficiency/sites/energyefficiency/files/files/documents/ICT_CoC/cocv5-
broadband_final.pdf.
®
[i.6] Cablelabs: "Data-Over-Cable Service Interface Specifications - DOCSIS 2.0 Interface".
®
[i.7] Cablelabs: "Data-Over-Cable Service Interface Specifications- DOCSIS 3.0 Interface".
[i.8] CENELEC EN 50643: "Electrical and electronic household and office equipment - Measurement
of networked standby power consumption of edge equipment".
[i.9] IEC 60050: "International Electrotechnical Vocabulary".
[i.10] Commission Regulation (EC) No 642/2009 of 22 July 2009 implementing Directive 2005/32/EC
of the European Parliament and of the Council with regard to ecodesign requirements for
televisions.
[i.11] IEC IEV ref 904-03-01: "Environmental standardization for electrical and electronic products and
systems".
NOTE: Available at http://www.electropedia.org/iev/iev.nsf/display?openform&ievref=904-03-01.
[i.12] IEEE 802.11™-2012: "IEEE Standard for Information technology -- Telecommunications and
information exchange between systems Local and metropolitan area networks -- Specific
requirements; Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications".
ETSI
---------------------- Page: 10 ----------------------
oSIST prEN 303 423 V1.2.9:2020
9 Draft ETSI EN 303 423 V1.2.9 (2020-03)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in CENELEC EN 50564 [1] and the following apply:
NOTE: When the present document is used to provide presumption of conformity to a European Directive or
Regulation, definitions given in the Directive or Regulation prevail.
edge equipment: networked equipment that can be connected to a network and interact with that network or other
equipment and that does not have, as its primary function, the passing of network traffic to provide a network
NOTE: Examples of edge equipment are given in Annex B.
interconnecting equipment: networked equipment that has, as its primary function, the passing of network traffic to
provide a network
NOTE: Examples of interconnecting equipment are given in Annex B.
logical network port: network technology running over a physical network port
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: Different communication protocols result in different network technologies.
low voltage external power supply: external power supply with a nameplate output voltage of less than 6 volts and a
nameplate output current greater than or equal to 550 milliamperes
NOTE: EC Commission Regulation No 278/2009 [i.3] definition.
network: communication infrastructure with a topology of links, an architecture, including the physical components,
organizational principles, communication procedures and formats (protocols)
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network availability: capability of the equipment to resume functions after a remotely initiated trigger has been
detected by a network port
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
network port: wired or wireless physical interface of the network connection located on the equipment through which
the equipment can be remotely activated
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: The International Electrotechnical Vocabulary (IEC 60050 [i.9]) defines "port (of a network)" as:
"a termination through which signals can enter or leave a network".
networked equipment: equipment that can connect to a network and has one or more network ports
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
networked standby: condition in which the equipment is able to resume a function by way of a remotely initiated
trigger from a network connection
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
physical network port: physical (hardware) medium of a network port. A physical network port can host two or more
network technologies
NOTE 1: EU Commission Regulation No 801/2013 [i.2] definition.
NOTE 2: A "physical network port" can consist of multiple "logical network ports".
ETSI
---------------------- Page: 11 ----------------------
oSIST prEN 303 423 V1.2.9:2020
10 Draft ETSI EN 303 423 V1.2.9 (2020-03)
power management: automatic control mechanism that achieves the smallest input power consistent with a
pre-determined level of functionality
NOTE: Source: IEV 904-03-01 [i.11], modified by omission of the note to entry.
reactivation trigger: signal that brings the equipment back to active mode
NOTE: The reactivation may be remotely initiated.
remotely initiated trigger: signal that comes from outside the equipment via a network
NOTE: EU Commission Regulation No 801/2013 [i.2] definition.
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ADSL Asymmetric Digital Subscriber Line
ADSL2plus Second generation ADSL with extended bandwidth
AP Access Point
CRC Cyclic Redundancy Check
®
DOCSIS Data Over Cable Service Interface Specification
DSL Digital Subscriber Line
EFTA European Free Trade Association
EPON Ethernet Passive Optical Network
EUT Equipment Under Test
FXS Foreign eXchange Station
GPON Gigabyte Passive Optical Network
HiNA High Network Availability
HPNA Home Phoneline Networking Alliance
LAN Local Area Network
POF Plastic Optical Fibber
PSD Power Spectral Density
QAM Quadrature Amplitude Modulation
RF Radio Frequency
USB Universal Serial Bus
VDSL Very high speed Digital Subscriber Line
VDSL2 Second generation VDSL
WAN Wide Area Network
WiMAX Worldwide interoperability for Microwave Access
XG-PON 10-Gigabit-capable Passive Optical Network
4 Information required for testing purposes
4.1 Information about networked port(s)
For each type of physical and associated logical networked port, the following information shall be provided by the
manufacturer:
a) the default time after which the power management function, or a similar function, automatically switches the
equipment into networked standby, and if available, the procedure for:
1) setting a time shorter than the default time; and/or
2) manually switching the equipment into networked standby.
ETSI
---------------------- Page: 12 ----------------------
oSIST prEN 303 423 V1.2.9:2020
11 Draft ETSI EN 303 423 V1.2.9 (2020-03)
b) the characteristics of the reactivation trigger (message, signal, etc.) that is used to reactivate the equipment
when in networked standby and how to remotely initiate it;
c) the maximum performance specifications, e.g. the maximum speed or data rate supported by that networked
port;
d) the (maximum) power consumption of the equipment in a condition providing networked standby into which
power management function, or a similar function, will switch the equipment, if only this port is used for
remote activation, e.g. the declared power consumption of the equipment under defined conditions for a type
of port;
e) the communication protocol used by equipment;
f) the radio frequency range at which each radio wireless logical network port operates;
g) the characteristics of wireless logical network ports other than radio wireless logical network ports.
NOTE: Annex D describes examples of product information for network equipment.
4.2 Power management function - periods & conditions
The manufacturer shall provide informatio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.