oSIST prEN ISO 19014-4:2024

Earth-moving machinery - Functional safety - Part 4: Design and evaluation of software and data transmission for safety-related parts of the control system (ISO/DIS 19014-4:2024)

This document specifies general principles for software development and signal transmission requirements of safety-related parts of machine-control systems (MCS) in earth-moving machinery (EMM) and its equipment, as defined in ISO 6165. In addition, this document addresses the significant hazards as defined in ISO 12100 related to the software embedded within the machine control system. The significant hazards being addressed are the incorrect machine control system output responses from machine control system inputs.
Cyber security is out of the scope of this document.
NOTE For guidance on cybersecurity, see an appropriate security standard.
This document is not applicable to EMM manufactured before the date of its publication.

Erdbaumaschinen - Funktionale Sicherheit - Teil 4: Gestaltung und Beurteilung von Software und Datenübertragung für sicherheitsrelevante Steuerungssysteme (ISO/DIS 19014-4:2024)

Dieses Dokument legt allgemeine Grundsätze für Anforderungen an Software-Entwicklung und Signalübertragung von sicherheitsbezogenen Teilen von Maschinensteuerungssystemen (MCS, en: machine-control systems) in Erdbaumaschinen (EMM, en: earth-moving machinery) und deren Ausrüstung, wie in ISO 6165:2012 definiert, fest. Zudem behandelt dieses Dokument die in ISO 12100 festgelegten signifikanten Gefährdungen in Bezug auf die im Maschinensteuerungssystem eingebettete Software. Bei den behandelten signifikanten Gefährdungen handelt es sich um das falsche Ansprechen der Ausgabe von Maschinensteuerungssystemen auf Eingaben in Maschinensteuerungssystemen.
Cybersicherheit liegt außerhalb des Anwendungsbereichs dieses Dokuments.
ANMERKUNG   Hinweise zur Cybersicherheit sind in einer geeigneten Sicherheitsnorm zu finden.
Dieses Dokument gilt nicht für EMM, die vor dem Veröffentlichungsdatum dieses Dokuments hergestellt wurden.

Engins de terrassement - Sécurité fonctionnelle - Partie 4: Conception et évaluation du logiciel et de la transmission des données pour les parties relatives à la sécurité du système de commande (ISO/DIS 19014-4:2024)

Le présent document spécifie les principes généraux applicables aux exigences en matière de développement de logiciel et de transmission des signaux des parties relatives à la sécurité des systèmes de commande de la machine (MCS) dans les engins de terrassement et leur équipement tels que définis dans l'ISO 6165. De plus, le présent document traite des phénomènes dangereux significatifs tels que définis dans l'ISO 12100 en rapport avec les logiciels intégrés dans le système de commande de la machine. Les phénomènes dangereux significatifs traités sont les réponses incorrectes du système de commande de la machine aux entrées du système de commande de la machine.
La cybersécurité n'est pas couverte par le présent document.
NOTE Voir une norme appropriée relative à la sécurité pour des recommandations à propos de la cybersécurité.
Le présent document n'est pas applicable aux engins de terrassement fabriqués avant la date de sa publication.

Stroji za zemeljska dela - Funkcijska varnost - 4. del: Načrtovanje in vrednotenje programske opreme in prenosa podatkov za dele krmilnega sistema, povezane z varnostjo (ISO/DIS 19014-4:2024)

General Information

• Status: Not Published
• Public Enquiry End Date: 17-Apr-2024
• ICS: 35.080 - Software
• ICS: 53.100 - Earth-moving machinery
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 01-Feb-2024
• Due Date: 20-Jun-2024
• Ref Project: prEN ISO 19014-4 - Earth-moving machinery - Functional safety - Part 4: Design and evaluation of software and data transmission for safety-related parts of the control system (ISO/DIS 19014-4:2024)

Relations

• Revises: SIST EN ISO 19014-4:2020 - Earth-moving machinery - Functional safety - Part 4: Design and evaluation of software and data transmission for safety-related parts of the control system (ISO 19014-4:2020)
• Effective Date: 04-Oct-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 19014-4:2024
01-marec-2024
Stroji za zemeljska dela - Funkcijska varnost - 4. del: Načrtovanje in vrednotenje
programske opreme in prenosa podatkov za dele krmilnega sistema, povezane z
varnostjo (ISO/DIS 19014-4:2024)
Earth-moving machinery - Functional safety - Part 4: Design and evaluation of software
and data transmission for safety-related parts of the control system (ISO/DIS 19014-
4:2024)
Erdbaumaschinen - Funktionale Sicherheit - Teil 4: Gestaltung und Beurteilung von
Software und Datenübertragung für sicherheitsrelevante Steuerungssysteme (ISO/DIS
19014-4:2024)
Engins de terrassement - Sécurité fonctionnelle - Partie 4: Conception et évaluation du
logiciel et de la transmission des données pour les parties relatives à la sécurité du
système de commande (ISO/DIS 19014-4:2024)
Ta slovenski standard je istoveten z: prEN ISO 19014-4
ICS:
35.080 Programska oprema Software
53.100 Stroji za zemeljska dela Earth-moving machinery
oSIST prEN ISO 19014-4:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 19014-4:2024

---------------------- Page: 2 ----------------------
oSIST prEN ISO 19014-4:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19014-4
ISO/TC 127/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:
2024-01-26 2024-04-19
Earth-moving machinery — Functional safety —
Part 4:
Design and evaluation of software and data transmission
for safety-related parts of the control system
Engins de terrassement — Sécurité fonctionnelle —
Partie 4: Conception et évaluation du logiciel et de la transmission des données pour les parties relatives à
la sécurité du système de commande
ICS: 53.100
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19014-4:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024

---------------------- Page: 3 ----------------------
oSIST prEN ISO 19014-4:2024
ISO/DIS 19014-4:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19014-4
ISO/TC 127/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:

Earth-moving machinery — Functional safety —
Part 4:
Design and evaluation of software and data transmission
for safety-related parts of the control system
Engins de terrassement — Sécurité fonctionnelle —
Partie 4: Conception et évaluation du logiciel et de la transmission des données pour les parties relatives à
la sécurité du système de commande
ICS: 53.100
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 19014-4:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO 2024 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 19014-4:2024
ISO/DIS 19014-4:2023(E)
Contents Page
Foreword .
...