Automatic electrical controls for household and similar use -- Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps

This part of IEC 60730 applies to the evaluation of thermal protectors for ballasts for tubular fluorescent lamps. This standard applies to thermal protectors using NTC or PTC thermistors, additional requirements for which are contained in Annex J. Requirements concerning the testing of the combination of ballasts and thermal protectors are given in IEC 61347-1. This standard applies to the inherent safety, to the operating values, operating times, and operating sequences where such are associated with equipment safety, and to the testing of thermal protectors used to protect ballasts for tubular lamps from overheating. This standard applies to thermal protectors for ballasts within the scope of IEC 61347-2-8. Thermal protectors covered by this standard may be suitable for ballasts for other discharge lamps such as ballasts under the scope of IEC 61347-2-9.
This International Standard applies to flexible cables with insulation based on ethylene propylene rubber (EPR), polyvinyl chloride (PVC) or silicone rubber (SiR) for portable earthing and short-circuiting equipment. For this type of cable no rated voltage is given as such cables are exclusively intended for earthing and short-circuiting equipment. The particular types of cable and their code designations are specified in Clause 6 of this standard. The test methods specified in this standard are given in IEC 60227-2, IEC 60245-2, IEC 60811 and IEC 62230.

Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche Anwendungen -- Teil 2-3: Besondere Anforderungen an thermische Schutzeinrichtungen für Vorschaltgeräte für röhrenförmige Leuchtstofflampen

Dispositifs de commande électrique automatiques à usage domestique et analogue -- Partie 2-3: Règles particulières pour les protecteurs thermiques des ballasts pour lampes tubulaires à fluorescence

La présente partie de la CEI 60730 s'applique à l'évaluation des protecteurs thermiques des ballasts pour lampes tubulaires à fluorescence. La présente norme s'applique aux protecteurs thermiques utilisant des thermistances CTN ou CTP, dont les exigences complémentaires sont contenues à l'Annexe J. Les exigences concernant les essais de la combinaison de ballasts et de protecteurs thermiques sont données dans la CEI 61347-1.

Avtomatske električne krmilne naprave za uporabo v gospodinjstvu in za podobno uporabo - 2-3. del: Posebne zahteve za toplotno zaščito predstikalnih naprav cevnih fluorescenčnih sijalk (IEC 60730-2-3:2006, spremenjen)

General Information

Status
Published
Publication Date
03-Apr-2008
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
10-Dec-2007
Due Date
01-Sep-2008
Completion Date
04-Apr-2008

Relations

Buy Standard

Standard
EN 60730-2-3:2008
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lampsDispositifs de commande électrique automatiques à usage domestique et analogue - Partie 2-3: Règles particulières pour les protecteurs thermiques des ballasts pour lampes tubulaires à fluorescenceAutomatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche Anwendungen - Teil 2-3: Besondere Anforderungen an thermische Schutzeinrichtungen für Vorschaltgeräte für röhrenförmige LeuchtstofflampenTa slovenski standard je istoveten z:EN 60730-2-3:2007SIST EN 60730-2-3:2008en,fr,de97.12029.140.30ICS:SIST EN 60730-2-3:1996/A11:2005SIST EN 60730-2-3:1996/A2:2002SIST EN 60730-2-3:1996SIST EN 60730-2-3:1996/A1:19981DGRPHãþDSLOVENSKI
STANDARDSIST EN 60730-2-3:200801-maj-2008







EUROPEAN STANDARD EN 60730-2-3 NORME EUROPÉENNE
EUROPÄISCHE NORM November 2007
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60730-2-3:2007 E
ICS 97.120; 29.140.30 Supersedes EN 60730-2-3:1992 + A1:1998 + A2:2001 + A11:2005
English version
Automatic electrical controls for household and similar use -
Part 2-3: Particular requirements for thermal protectors
for ballasts for tubular fluorescent lamps (IEC 60730-2-3:2006, modified)
Dispositifs de commande électrique automatiques à usage domestique
et analogue -
Partie 2-3: Règles particulières
pour les protecteurs thermiques
des ballasts pour lampes tubulaires
à fluorescence (CEI 60730-2-3:2006, modifiée)
Automatische elektrische
Regel- und Steuergeräte
für den Hausgebrauch
und ähnliche Anwendungen -
Teil 2-3: Besondere Anforderungen
an thermische Schutzeinrichtungen
für Vorschaltgeräte für röhrenförmige Leuchtstofflampen (IEC 60730-2-3:2006, modifiziert)
This European Standard was approved by CENELEC on 2007-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.



EN 60730-2-3:2007 - 2 - Foreword The text of the International Standard IEC 60730-2-3:2006, prepared by IEC TC 72, Automatic controls for household use, together with the common modifications prepared by the Technical Committee CENELEC TC 72, Automatic controls for household use, was submitted to the formal vote and was approved by CENELEC as EN 60730-2-3 on 2007-09-01. This European Standard supersedes EN 60730-2-3:1992 + corrigendum March 2001 + A1:1998 + corrigendum March 2001 + A2:2001 + A11:2005. The following dates were fixed: – latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement
(dop)
2008-09-01 – latest date by which the national standards conflicting with the EN have to be withdrawn
(dow)
2010-09-01 This Part 2-3 is to be used in conjunction with EN 60730-1:2000 + A1:2004, Automatic electrical controls for household and similar use – Part 1: General requirements, and any subsequent amendments. This Part 2-3 supplements or modifies the corresponding clauses in EN 60730-1 so as to convert that publication into the European Standard: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps. Where this Part 2-3 states "addition", "modification" or "replacement", the relevant requirement, test specification or explanatory matter in Part 1 shall be adapted accordingly. Where no change is necessary, this Part 2-3 indicates that the relevant clause or subclause applies. In this publication, the following print types are used: – Requirements proper: in roman type. – Test specifications: in italic type. – Explanatory matter: in smaller roman type. Subclauses, notes, items or figures which are additional to those in Part 1 are numbered starting from 101, additional annexes are lettered AA, BB, etc. __________



- 3 - EN 60730-2-3:2007 Endorsement notice
The text of the International Standard IEC 60730-2-3:2006 was approved by CENELEC as a European Standard with agreed common modifications as given below. COMMON MODIFICATIONS
7 Information
In Table 7.2 delete item 101 and its note and replace both with “Void”.
12 Moisture and dust resistance
Replace the text with “This clause of Part 1 is applicable”.
12.2 Protection against humid conditions
Delete this subclause.
17 Overload, endurance and limited short-circuit
Replace this heading with “17
Overload and endurance”.
17.1 General requirements
17.1.1
Replace the second sentence with:
“Separate samples shall be used for the overload and endurance tests.”
17.4 Limited short circuit
Delete this subclause.
Annex C Cotton used for mercury switch test
Delete this annex.



EN 60730-2-3:2007 - 4 - Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Addition to Annex ZA of EN 60730-1: Publication Year Title EN/HD Year
IEC 61347-1 -1) Lamp controlgear -
Part 1: General and safety requirements EN 61347-1 20012)
IEC 61347-2-8 -1) Lamp controlgear -
Part 2-8: Particular requirements
for ballasts for fluorescent lamps EN 61347-2-8 + corr. July
20012) 2003
IEC 61347-2-9 -1) Lamp controlgear -
Part 2-9: Particular requirements
for ballasts for discharge lamps (excluding fluorescent lamps) EN 61347-2-9 + corr. July
20012) 2003
1) Undated reference. 2) Valid edition at date of issue.



NORME INTERNATIONALECEIIEC INTERNATIONAL STANDARD 60730-2-3Deuxième éditionSecond edition2006-10 Dispositifs de commande électrique
automatiques à usage domestique et analogue – Partie 2-3: Règles particulières pour les protecteurs thermiques des ballasts pour lampes
tubulaires à fluorescence
Automatic electrical controls
for household and similar use – Part 2-3: Particular requirements for thermal protectors
for ballasts for tubular fluorescent lamps Pour prix, voir catalogue en vigueur For price, see current catalogue© IEC 2006
Droits de reproduction réservés

Copyright - all rights reserved Aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch
Web: www.iec.ch CODE PRIX PRICE CODE N Commission Electrotechnique InternationaleInternational Electrotechnical Commission



60730-2-3 © IEC:2006 – 3 –
CONTENTS FOREWORD.5
1 Scope and normative references.11 2 Definitions.13 3 General requirements.13 4 General notes on tests.13 5 Rating.13 6 Classification.13 7 Information.15 8 Protection against electric shock.17 9 Provision for protective earthing.17 10 Terminals and terminations.19 11 Constructional requirements.19 12 Moisture and dust resistance.19 13 Electric strength and insulation resistance.19 14 Heating.19 15 Manufacturing deviation and drift.19 16 Environmental stress.21 17 Overload, endurance and limited short-circuit.21 18 Mechanical strength.25 19 Threaded parts and connections.25 20 Creepage distances, clearances and distances through solid insulation.25 21 Resistance to heat, fire and tracking.27 22 Resistance to corrosion.27 23 Electromagnetic compatibility (EMC) requirements – emission.27 24 Components.27 25 Normal operation.27 26 Electromagnetic compatibility (EMC) requirements – immunity.27 27 Abnormal operation.27 28 Guidance on the use of electronic disconnection.27
Annexes.29 Annex C (normative)
Cotton used for mercury switch test.29 Annex E (normative)
Circuit for measuring leakage current.29



60730-2-3 © IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE –
Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60730-2-3 has been prepared by IEC technical committee 72: Automatic controls for household use. This second edition cancels and replaces the first edition published in 1990, Amendment 1 (1995) and Amendment 2 (2001).
This second edition constitutes a technical revision.
This new edition updates the standard to IEC 60730-1, Edition 3 (1999) and its Amendment 1 (2003).



60730-2-3 © IEC:2006 – 7 –
The text of this standard is based upon the following documents:
FDIS Report on voting 72/709/FDIS 72/722/RVD
Full information on the voting for the approval of this part can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This Part 2-3 is intended to be used in conjunction with IEC 60730-1. It was established on the basis of the third edition of that standard (1999) and its amendment 1 (2003). Consideration may be given to future editions of, or amendments to, IEC 60730-1. This Part 2-3 supplements or modifies the corresponding clauses in IEC 60730-1 so as to convert that publication into the IEC standard: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps. Where this Part 2-3 states "addition", "modification" or "replacement", the relevant requirement, test specification or explanatory matter in Part 1 shall be adapted accordingly. Where no change is necessary, this Part 2-3 indicates that the relevant clause or subclause applies. In the development of a fully international standard, it has been necessary to take into consideration the differing requirements resulting from practical experience in various parts of the world and to recognize the variation in national electrical systems and wiring rules. The ‘in some countries’ notes regarding
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.