SIST EN 15027:2008/kprA1:2008

Transportable wall saw and wire saw equipment for job site - Safety

Transportable Wand- und Seilsägen für den Baustelleneinsatz - Sicherheit

Scies murales et scies à fil transportables de chantier - Sécurité

Oprema za prenosne stenske in žične žage za delovišča - Varnost

General Information

• Status: Not Published
• Public Enquiry End Date: 31-Dec-2008
• ICS: 25.080.60 - Sawing machines
• ICS: 91.220 - Construction equipment
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 14-Oct-2019
• Due Date: 19-Oct-2019
• Completion Date: 14-Oct-2019
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 15027:2007/prA1 - Transportable wall saw and wire saw equipment for job site - Safety

Relations

• Consolidated By: SIST EN 15027:2008+A1:2009 - Transportable wall saw and wire saw equipment for job site - Safety
• Effective Date: 18-Jan-2023
• Revised: SIST EN 15027:2008 - Transportable wall saw and wire saw equipment for job site - Safety
• Effective Date: 01-Dec-2008
• Consolidated By: SIST EN 15027:2008+A1:2009 - Transportable wall saw and wire saw equipment for job site - Safety
• Effective Date: 19-Jan-2023
• Consolidated By: SIST EN 15027:2008+A1:2009 - Transportable wall saw and wire saw equipment for job site - Safety
• Effective Date: 01-May-2009

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15027:2008/kprA1:2008
01-december-2008
2SUHPD]DSUHQRVQHVWHQVNHLQåLþQHåDJH]DGHORYLãþD9DUQRVW
Transportable wall saw and wire saw equipment for job site - Safety
Transportable Wand- und Seilsägen für den Baustelleneinsatz - Sicherheit
Scies murales et scies à fil transportables de chantier - Sécurité
Ta slovenski standard je istoveten z: EN 15027:2007/prA1
ICS:
25.080.60 Strojne žage Sawing machines
91.220 Gradbena oprema Construction equipment
SIST EN 15027:2008/kprA1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 15027:2008/kprA1:2008

---------------------- Page: 2 ----------------------

SIST EN 15027:2008/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 15027:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 25.080.60; 91.220

English Version
Transportable wall saw and wire saw equipment for job site -
Safety
Scies murales et scies à fil transportables de chantier - Transportable Wand- und Seilsägen für den
Sécurité Baustelleneinsatz - Sicherheit
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 15027:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15027:2007/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 15027:2008/kprA1:2008
EN 15027:2008/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 2, Normative references .4
3 Modification to Table 1 — List of significant hazards.4
4 Modification to 5.1, General.4
5 Modification to 5.2.2.1, Moving parts not involved in the working process.4
6 Modification to 5.2.3, Stability .5
7 Modification to 5.2.8.2, Start and stop control for rotation and feed .5
8 Modification to 5.3, Electrical hazards .5
9 Modification to 7.2.1, Regular marking.5
10 Modification to 7.2.2, Other information.6
11 Modification to 7.3.2.1, Description of the machine.6
12 Modification to 7.3.2.3, Instructions for the installation and use of the machine.6
13 Modification to 7.3.4, Spare parts list .6
14 Modification to Annex A (normative) Noise test code – Grade 2 of accuracy .7
15 Addition of Annex ZB .7
16 Modification to the Bibliography.7


2

---------------------- Page: 4 ----------------------

SIST EN 15027:2008/kprA1:2008
EN 15027:2008/prA1:2008 (E)
Foreword
This document (EN 15027:2008/prA1:2008) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
3

---------------------- Page: 5 ----------------------

SIST EN 15027:2008/kprA1:2008
EN 15027:2008/prA1:2008 (E)
1 Modification to the Foreword
th
Replace the 5 paragraph with th
...