oSIST prEN 12875-2:2024
(Main)Mechanical dishwashing resistance of utensils - Part 2: Inspection and evaluation
Mechanical dishwashing resistance of utensils - Part 2: Inspection and evaluation
This document specifies the conditions for the visual inspection of non-metallic tableware in contact with foodstuffs after testing its dishwashing resistance according to the procedures described in the relevant parts of the EN 12875 series for articles for domestic, industrial and catering use.
Spülmaschinenfestigkeit von Gegenständen - Teil 2: Begutachtung von nichtmetallischen Gegenstäden
Dieses Dokument legt die Bedingungen für die visuelle Begutachtung von Haushaltswaren aus Keramik, Glas, Glaskeramik, Dekorglas, Emaille, Beschichtungen, Gummi, Silikon, Metall und Kunststoffen fest, nachdem deren Spülmaschinenbeständigkeit entsprechend den Verfahren in den jeweiligen Teilen der Normenreihe EN 12875 geprüft wurde.
Résistance mécanique au lave-vaisselle des ustensiles - Partie 2: Inspection des articles non-métalliques
Le présent document spécifie les conditions d’examen visuel des articles à usage domestique en céramique, verre, vitrocéramique, verre décoré, émail vitrifié, revêtements, caoutchouc, métal et plastique, à l’issue des essais de leur résistance au lave-vaisselle conformément aux modes opératoires décrits dans les parties pertinentes de la série EN 12875.
Odpornost posode in pribora za domačo uporabo proti mehanskemu pranju - 2. del: Pregled in vrednotenje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Odpornost posode in pribora za domačo uporabo proti mehanskemu pranju - 2.
del: Pregled in vrednotenje
Mechanical dishwashing resistance of utensils - Part 2: Inspection and evaluation
Spülmaschinenfestigkeit von Gegenständen - Teil 2: Begutachtung von
nichtmetallischen Gegenstäden
Résistance mécanique au lave-vaisselle des ustensiles - Partie 2: Inspection des articles
non-métalliques
Ta slovenski standard je istoveten z: prEN 12875-2
ICS:
97.040.40 Pomivalni stroji Dishwashers
97.040.60 Kuhinjska posoda, jedilni Cookware, cutlery and
servisi in jedilni pribor flatware
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2024
ICS 67.250; 97.040.40; 97.040.60 Will supersede EN 12875-2:2001
English Version
Mechanical dishwashing resistance of utensils - Part 2:
Inspection and evaluation
Résistance mécanique au lave-vaisselle des ustensiles - Spülmaschinenfestigkeit von Gegenständen - Teil 2:
Partie 2: Inspection des articles non-métalliques Begutachtung von nichtmetallischen Gegenstäden
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 194.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12875-2:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Inspectors . 5
6 Apparatus . 5
7 Samples . 6
8 Procedure . 6
8.1 General. 6
8.2 Inspection . 6
9 Test report . 8
10 Marking . 8
Annex A (informative) Inspection protocol . 10
Bibliography . 15
European foreword
This document (prEN 12875-2:2024) has been prepared by Technical Committee CEN/TC 194 “Utensils
in contact with food”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12875-2:2001.
This document includes the following significant technical changes with respect to EN 12875-2:2001:
— extension of the scope of application to include non-metallic articles;
— minor adjustments to the evaluation procedure;
— Clarification of the evaluation criteria;
— insertation of the section “Number of test cycles”;
— insertation of an alternative marking;
— insertation of the informative Annex A “Inspection protocol”;
— editorial changes.
Introduction
This document specifies the conditions for visual inspection and evaluation of metallic and non-metallic
utensils in connection with the standardized dishwashing resistance tests including the expression of
results.
Further parts of EN 12875, under the general title Mechanical dishwashing resistance of utensils are as
follows:
— Part 1: Reference test method for domestic articles
— Part 4: Rapid test for domestic ceramic articles
— Part 5: Rapid test for ceramic catering articles
NOTE The marking based on these test results is primarily intended as consumer information. In the opinion
of consumers other features of equivalent importance exist which are not always compatible with high dishwashing
resistance requirement.
1 Scope
This document specifies the conditions for the visual inspection of domestic articles made from ceramic,
glass, glass ceramic, decorated glass, vitreous enamel, coatings, rubber, silicones, metal, and plastics after
testing its dishwashing resistance according to the procedures described in the relevant parts of the
EN 12875 series.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
prEN 12875-1, Mechanical dishwashing resistance of utensils — Part 1: Reference test method for domestic
articles
3 Terms and definitions
No terms and definitions are listed in this document.
4 Principle
The surface of at least three samples preferably from different lots, which have been tested are visually
inspected under defined conditions in comparison to an unused sample by two inspectors. Depending on
the type of article, the differences in the surfaces of the tested samples from the surface of the unused
sample are recorded.
5 Inspectors
At least two inspectors are required who are familiar with the inspection procedure described in this
document. Each inspector shall be able to see the surface of the specimens clearly with the naked eye (or
with a habitual vision aid) and shall have normal colour vision. The clothing of the inspectors should not
impact the visual evaluation (e.g. the reflectance of the colour).
NOTE Suitable methods for assessing colour vision are the H-R-R-Pseudoisochromatic Plates or the Ishihara
Test for Colour Blindness [1].
6 Apparatus
6.1 Linen cloth for wiping off surface residues and wiping decorated surfaces.
6.2 Inspection site
An inspection site, which:
— is protected from external light, and illuminated vertically by a diffuse daylight (6 000 to 6 500) K
lamp yielding 1 000 lx near the specimens;
— shows grey colour (RGB 146/142/133) and a dull surface finish on all surfaces exposed to the
artificial light;
— has sufficient table area to accommodate all of the specimens of one type simultaneously.
7 Samples
For each article at least three unused test specimens of identical shape, size, and surface finish preferably
from different lots shall be tested, and a fourth test specimen shall be retained for reference.
8 Procedure
8.1 General
Before inspection, easily removable deposits shall be eliminated by wiping with a cloth and/or washing
by hand in a mild liquid detergent at about 45 °C followed by rinsing and drying.
8.2 Inspection
8.2.1 General
Inspection is carried o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.