SIST EN IEC 60136:2024
(Main)Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for electrical machinery (IEC 60136:2024)
Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for electrical machinery (IEC 60136:2024)
IEC 60136:2024 applies primarily to brushes and brush-holders for cylindrical commutators and slip rings for electrical rotating machines. Some clauses of this document may cover other configurations, such as flat commutators or plain disks. It defines the dimensions of brushes and their components, together with their tolerances:
- dimensions of brush block (t, a, r),
- angles α and β,
- chamfer,
- flexibles (shunts),
- standard terminals.
It also covers the conventional designation of principal dimensions, the marking of brushes and the testing methods for the qualification of brushes after their manufacturing (except the brush grade material, covered by IEC 60413). This third edition cancels and replaces the second edition published in 1986 and Amendment 1:1995. This edition constitutes a technical revision.
Please refer to the Foreword of the document for a comprehensive listing of the changes with respect to the previous edition.
Abmessungen, Kennzeichnung und Prüfung von Kohlebürsten und Abmessungen von Bürstenhaltern für elektrische Maschinen (IEC 60136:2024)
Dimensions, marquages et essais des balais et dimensions des porte-balais pour machines électriques (IEC 60136:2024)
IEC 60136:2024 s'applique principalement aux balais et aux porte-balais montés sur collecteurs cylindriques et bagues des machines électriques tournantes. Certains articles du présent document peuvent couvrir d'autres configurations, comme les collecteurs plats ou les disques lisses. Il définit les dimensions des balais et de leurs composants, ainsi que leurs tolérances:
- dimensions du bloc de balai (t, a, r);
- angles α et β;
- chanfrein;
- câbles (shunts);
- cosses normalisées.
Il couvre également la désignation conventionnelle des dimensions principales, le marquage des balais et les méthodes d'essai pour la qualification des balais après leur fabrication (à l'exception du matériau de la nuance des balais, couvert par l'IEC 60413). Cette troisième édition annule et remplace la deuxième édition parue en 1986 et l'Amendement 1:1995. Cette édition constitue une révision technique.
Veuillez vous référer à l'avant-propos du document pour une liste complète des modifications par rapport à l'édition précédente.
Mere, označevanje in preskušanje grafitnih ščetk ter mere držal ščetk za električne stroje (IEC 60136:2024)
Standard IEC 60136:2024 se uporablja predvsem za ščetke in držala ščetk za valjaste komutatorje in drsne obroče v električnih rotacijskih strojih. Nekatere točke tega dokumenta lahko obravnavajo druge konfiguracije, kot so ploščati komutatorji ali navadni diski. Določa mere ščetk in njihovih komponent ter tolerance:
– mere bloka ščetke (t, a, r);
– kota α in β;
– zareza/posnetje;
– prilagodljivi elementi (vzporedni priključki);
– standardni priključki.
Zajema tudi konvencionalno označevanje glavnih mer, označevanje ščetk in preskusne metode za kvalifikacijo ščetk po njihovi izdelavi (razen krtačnih materialov, zajetih v standardu IEC 60413). Tretja izdaja razveljavlja in nadomešča drugo izdajo, objavljeno leta 1986, ter dopolnilo 1:1995. Ta izdaja je tehnično popravljena izdaja.
Za izčrpen seznam sprememb v primerjavi s prejšnjo izdajo glej poglavje »Predgovor« v tem dokumentu.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Mere, označevanje in preskušanje grafitnih ščetk ter mere držal ščetk za električne
stroje (IEC 60136:2024)
Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for
electrical machinery (IEC 60136:2024)
Abmessungen, Kennzeichnung und Prüfung von Kohlebürsten und Abmessungen von
Bürstenhaltern für elektrische Maschinen (IEC 60136:2024)
Dimensions, marquages et essais des balais et dimensions des porte-balais pour
machines électriques (IEC 60136:2024)
Ta slovenski standard je istoveten z: EN IEC 60136:2024
ICS:
29.160.10 Sestavni deli rotacijskih Components for rotating
strojev machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60136
NORME EUROPÉENNE
EUROPÄISCHE NORM June 2024
ICS 29.160.10
English Version
Dimensions, marking and testing of carbon brushes and
dimensions of brush-holders for electrical machinery
(IEC 60136:2024)
Dimensions, marquages et essais des balais et dimensions Abmessungen, Kennzeichnung und Prüfung von
des porte-balais pour machines électriques Kohlebürsten und Abmessungen von Bürstenhaltern für
(IEC 60136:2024) elektrische Maschinen
(IEC 60136:2024)
This European Standard was approved by CENELEC on 2024-06-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60136:2024 E
European foreword
The text of document 2/2180/FDIS, future edition 3 of IEC 60136, prepared by IEC/TC 2 "Rotating
machinery" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-03-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-06-12
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60136:2024 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60773:2021 NOTE Approved as EN IEC 60773:2021 (not modified)
ISO 3611 NOTE Approved as EN ISO 3611
ISO 13102:2012 NOTE Approved as EN ISO 13102:2012 (not modified)
ISO 13385-1:2019 NOTE Approved as EN ISO 13385-1:2019 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60276 2018 Carbon brushes, brush holders, EN IEC 60276 2019
commutators and slip-rings - Definitions
and nomenclature
IEC 60560 - Definitions and terminology of brush- - -
holders for electrical machines
ISO 129-1 - Technical product documentation (TPD) - EN ISO 129-1 -
Presentation of dimensions and tolerances
- Part 1: General principles
ISO 197-1 1983 Copper and copper alloys - Terms and - -
definitions - Part 1: Materials
ISO 286-2 2010 Geometrical product specifications (GPS) - EN ISO 286-2 2010
ISO code system for tolerances on linear
sizes - Part 2: Tables of standard tolerance
classes and limit deviations for holes and
shafts
IEC 60136 ®
Edition 3.0 2024-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Dimensions, marking and testing of carbon brushes and dimensions of brush-
holders for electrical machinery
Dimensions, marquages et essais des balais et dimensions des porte-balais
pour machines électriques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.160.10 ISBN 978-2-8322-8835-1
– 2 – IEC 60136:2024 © IEC 2024
CONTENTS
FOREWORD . 7
1 Scope . 10
2 Normative references . 10
3 Terms, definitions and symbols. 11
3.1 Terms and definitions . 11
3.2 Symbols . 19
4 Units and marking . 21
4.1 Units . 21
4.2 Marking . 21
4.2.1 Units . 21
4.2.2 Additional marks on the brush. 21
4.2.3 Additional marks for brush-holders . 22
5 Principal dimensions and tolerances of brushes. 22
5.1 Sequence . 22
5.2 Standard dimensions . 24
5.3 Tolerances on principal dimensions . 24
5.3.1 General tolerances . 24
5.3.2 Split brushes . 25
5.3.3 Metal-graphite brushes . 26
5.4 Recommended combinations of principal dimensions . 26
5.4.1 Combination for t and a . 26
5.4.2 Square brush . 29
6 Complementary dimensions of brushes . 30
6.1 Chamfers . 30
6.1.1 Angle . 30
6.1.2 Dimension . 30
6.1.3 Non-reversing chamfer . 31
6.2 Angles for contact and top bevels . 32
6.2.1 Angles for contact bevel . 32
6.2.2 Angles for top bevel . 33
6.2.3 Combination of angles . 34
6.3 Pressure area . 34
6.4 Depth of insertion q of the flexible (shunt) in the brush . 35
i
6.5 Residual material width adjacent to the flexible . 36
6.6 Safe length of a worn brush r . 37
m
7 Terminations of brushes: flexibles and terminals. 38
7.1 Flexibles . 38
7.1.1 General . 38
7.1.2 Nominal area and maximum diameter of flexibles . 39
7.1.3 Length of flexible . 40
7.1.4 Flexible protection . 40
7.2 Terminals . 40
7.2.1 General . 40
7.2.2 Axial spade terminals . 41
7.2.3 Flag terminals . 42
7.2.4 Double shoe terminals . 43
IEC 60136:2024 © IEC 2024 – 3 –
7.2.5 Tubular terminals . 44
7.2.6 Soldered terminals . 45
7.2.7 Current capacity of terminals . 46
8 Test procedures for determining physical properties of brushes . 47
8.1 General . 47
8.2 Measurement of electrical resistance of brush/flexible connection . 47
8.2.1 General . 47
8.2.2 Test equipment . 48
8.2.3 Test procedure . 50
8.2.4 Test procedure for method b) (mathematical). 55
8.2.5 Calculation and report . 56
8.3 Measurement of the pull strength of tamped or moulded connections . 56
8.3.1 General . 56
8.3.2 Principle . 56
8.3.3 Test equipment . 56
8.3.4 Test procedure . 59
8.3.5 Calculation and report . 59
9 Brush-holder dimensions and configuration .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.