SIST EN 62339-1:2007

Modular component interfaces for surface-mount fluid distribution components -- Part 1: Elastomeric seals

This International Standard applies to all types of surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. This includes components such as valves, filters, regulators, transducers, and controllers. The scope of this standard is limited as follows. a) This standard addresses only surface-mount fluid distribution components and proper sealing methods. This standard is limited to sealing methods using elastomeric material for the seals. b) The designs of the actual system components and the flow substrate are not specified in this standard. Any indication of mounting direction or other indexing is left to the manufacturer as required for its equipment. c) Users shall be aware that, on the basis of the stream conditions of their processes, other technologies and components may be readily available. d) This standard does not address the effects of various stream conditions on the technical functionality of the component. e) This standard does not address maintenance concerns for the components. f) This standard does not refer to design issues pertaining to specific safety requirements. These issues should be referenced to other standards, organizations, and recommended guidelines. g) International, national, and local codes, regulations, and laws should be consulted to ensure that each component meets the user's regulatory requirements. The object of this standard is to establish properties and physical dimensions that define the interface for surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. The interface controls the dimensions and location of the sealing surfaces to allow change of just one element of the system without modification of the entire system. This is what makes the system modular from both a design and a maintenance standpoint.

Modulare-Komponenten-Schnittstellen für oberflächenmontierte Bauteile zur Flüssigkeitsverteilung -- Teil 1: Elastomere Dichtungen

Interfaces de composants modulaires pour les composants de distribution de fluide montés en surface - Partie 1: Scellements élastomères

La CEI 62339-1:2006 établit les propriétés et les dimensions physiques qui définissent l'interface pour les composants de distribution de fluide montés en surface équipés de dispositifs d'étanchéité en élastomère utilisés dans les systèmes d'analyseurs de processus et de traitement des échantillons. L'interface contrôle les dimensions et l'emplacement des surfaces d'étanchéité pour permettre de changer un seul élément du système sans modification de tout le système. C'est cet aspect qui rend le système modulaire tant du point de vue de la conception que de l'entretien. Elle annule et remplace la CEI/PAS 62339-1 publiée en 2003. Cette première édition constitue une révision technique.

Vmesni sestavni deli naprav za določanje pretoka tekočin - 1. del: Elastomerna tesnila (IEC 62339-1:2006)

General Information

• Status: Published
• Publication Date: 14-Oct-2007
• ICS: 23.040.80 - Seals for pipe and hose assemblies
• ICS: 25.040.40 - Industrial process measurement and control
• Technical Committee: MOV - Measuring equipment for electromagnetic quantities
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Oct-2007
• Due Date: 10-Dec-2007
• Completion Date: 15-Oct-2007
• Ref Project: EN 62339-1:2007 - Modular component interfaces for surface-mount fluid distribution components - Part 1: Elastomeric seals

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62339-1:2007
01-november-2007
9PHVQLVHVWDYQLGHOLQDSUDY]DGRORþDQMHSUHWRNDWHNRþLQGHO(ODVWRPHUQD
WHVQLOD,(&
Modular component interfaces for surface-mount fluid distribution components - Part 1:
Elastomeric seals
Modulare-Komponenten-Schnittstellen für oberflächenmontierte Bauteile zur
Flüssigkeitsverteilung - Teil 1: Elastomere Dichtungen
Interfaces de composants modulaires pour les composants de distribution de fluide
montés en surface - Partie 1: Scellements élastomeres
Ta slovenski standard je istoveten z: EN 62339-1:2007
ICS:
23.040.80 Tesnila za cevne zveze Seals for pipe and hose
assemblies
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
SIST EN 62339-1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 62339-1

NORME EUROPÉENNE
April 2007
EUROPÄISCHE NORM

ICS 23.040.80; 25.040.40


English version


Modular component interfaces
for surface-mount fluid distribution components -
Part 1: Elastomeric seals
(IEC 62339-1:2006)


Interfaces de composants modulaires Modulare-Komponenten-Schnittstellen
pour les composants de distribution für oberflächenmontierte Bauteile
de fluide montés en surface - zur Flüssigkeitsverteilung -
Partie 1: Scellements élastomères Teil 1: Elastomere Dichtungen
(CEI 62339-1:2006) (IEC 62339-1:2006)




This European Standard was approved by CENELEC on 2007-03-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in two official versions (English and German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62339-1:2007 E

---------------------- Page: 2 ----------------------

EN 62339-1:2007 - 2 -
Foreword
The text of document 65D/130/FDIS, future edition 1 of IEC 62339-1, prepared by the former SC 65D,
Analyzing equipment, of IEC TC 65, Industrial-process measurement and control, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 62339-1 on 2007-03-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62339-1:2006 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
ISO 4288 NOTE  Harmonized as EN ISO 4288:1997 (not modified).
__________

---------------------- Page: 3 ----------------------

- 3 - EN 62339-1:2007
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

ANSI/ISA-76.00.02 2002 Modular Component Interfaces for - -
Surface-Mount Fluid Distribution
Components -
Part 1: Elastomeric Seals

---------------------- Page: 4 ----------------------

INTERNATIONAL IEC


STANDARD 62339-1





First edition
2006-12


Modular component interfaces for surface-mount
fluid distribution components –
Part 1:
Elastomeric seals
© IEC 2006 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale H
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

---------------------- Page: 5 ----------------------

– 2 – 62339-1 © IEC:2006(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

MODULAR COMPONENT INTERFACES FOR SURFACE-MOUNT
FLUID DISTRIBUTION COMPONENTS –

Part 1: Elastomeric seals


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its techni
...