SIST EN 60311:2003
(Main)Electric irons for household or similar use - Methods for measuring performance
Electric irons for household or similar use - Methods for measuring performance
States and defines the principal performance characteristics of electric dry irons, steam irons, spray irons,and steam irons with seperate water reservoir or boiler/generator not exceeding 5L in capacity, for household or similar use.
Elektrische Bügeleisen für Haushalt und ähnliche Zwecke - Verfahren zur Messung der Gebrauchseigenschaften
Fers à repasser électriques pour usage domestique ou analogue - Méthodes de mesure de l'aptitude à la fonction
L'IEC 60311:2002 est applicable aux fers à repasser électriques pour usage domestique ou analogue. La présente Norme a pour objet d'énumérer et de définir les principales caractéristiques d'aptitude à la fonction des fers à repasser électriques pour usage domestique ou analogue intéressant l'utilisateur et de décrire les méthodes normalisées pour la vérification de ces caractéristiques.
Les fers à repasser électriques couverts par la présente Norme comprennent:
- les fers fonctionnant à sec;
- les fers à production de vapeur;
- les fers à pulvérisation d'eau;
- les fers à production de vapeur avec réservoir d'eau séparé ou bouilleur/générateur de vapeur dont la capacité ne dépasse pas 5 l.
La présente Norme ne traite pas des exigences de sécurité, ni des exigences concernant l'aptitude à la fonction.
Electric irons for household or similar use - Methods for measuring performance
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60311:2003
01-december-2003
1DGRPHãþD
SIST EN 60311:2000
SIST EN 60311:2000/A1:2000
SIST EN 60311:2000/A2:2000
Electric irons for household or similar use - Methods for measuring performance
Electric irons for household or similar use - Methods for measuring performance
Elektrische Bügeleisen für Haushalt und ähnliche Zwecke - Verfahren zur Messung der
Gebrauchseigenschaften
Fers à repasser électriques pour usage domestique ou analogue - Méthodes de mesure
de l'aptitude à la fonction
Ta slovenski standard je istoveten z: EN 60311:2003
ICS:
97.060 Aparati za nego perila Laundry appliances
SIST EN 60311:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60311:2003
---------------------- Page: 2 ----------------------
SIST EN 60311:2003
EUROPEAN STANDARD EN 60311
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2003
ICS 97.060 Supersedes EN 60311:1997 + A1:1997 + A2:2000
English version
Electric irons for household or similar use –
Methods for measuring performance
(IEC 60311:2002)
Fers à repasser électriques Elektrische Bügeleisen für Haushalt und
pour usage domestique ou analogue - ähnliche Zwecke –
Méthodes de mesure de l'aptitude Verfahren zur Messung
à la fonction der Gebrauchseigenschaften
(CEI 60311:2002) (IEC 60311:2002)
This European Standard was approved by CENELEC on 2003-07-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60311:2003 E
---------------------- Page: 3 ----------------------
SIST EN 60311:2003
EN 60311:2003 - 2 -
Foreword
The text of the International Standard IEC 60311:2002, prepared by SC 59E, Ironing and pressing
appliances, of IEC TC 59, Performance of household electrical appliances, was submitted to the
Unique Acceptance Procedure and was approved by CENELEC as EN 60311 on 2003-07-01 without
any modification.
This European Standard supersedes EN 60311:1997 + A1:1997 + A2:2000.
The following dates were fixed:
– latest date by which the EN has to be implemented (dop) 2004-07-01
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards (dow) 2006-07-01
conflicting with the EN have to be withdrawn
Annexes designated "normative" are part of the body of the standard.
Annexes designated "informative" are given for information only.
In this standard, Annexes B, C and ZA are normative and Annexes A and D are informative.
Annex ZA has been added by CENELEC.
In this standard, the following print types are used:
– test specifications: italic type;
– In small roman type;
– other texts: in roman type;
Words in bold in the text are defined in Clause 3.
__________
Endorsement notice
The text of the International Standard IEC 60311:2002 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 4 ----------------------
SIST EN 60311:2003
- 3 - EN 60311:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60051-1 1997 Direct acting indicating analogue electrical EN 60051-1 1998
measuring instruments and their
accessories
Part 1: Definitions and general
requirements common to all parts
IEC 60454-3-3 1998 Pressure-sensitive adhesive tapes for EN 60454-3-3 1998
electrical purposes
Part 3: Specifications for individual
materials - Sheet 3: Polyester film tapes
with rubber thermoplastic adhesive
IEC 60734 2001 Household electrical appliances - EN 60734 2003
Performance - Hard water for testing
ISO 105-F 1985 Textiles - Tests for colour fastness - -
Part F: Standard adjacent fabrics
ISO 1518 1992 Paints and varnishes - Scratch test EN ISO 1518 2000
ISO 2409 1992 Paints and varnishes - Cross-cut test EN ISO 2409 1994
ISO 3758 1991 Textiles - Care labelling code using symbols EN 23758 1993
ISO 3801 1977 Textiles - Woven fabrics - Determination of - -
mass per unit length and mass per unit area
ISO 6330 2000 Textiles - Domestic washing and drying EN ISO 6330 2000
procedures for textile testing
ISO 7211-2 (mod) 1984 Textiles - Woven fabrics - Construction - EN 1049-2 1993
Methods of analysis
Part 2: Determination of number of threads
per unit length
ISO 9073-2 1995 Textiles - Test methods for nonwovens – EN ISO 9073-2 1996
Part 2: Determination of thickness
ISO 4-1 1999 Textiles - Tensile properties of fabrics -- EN ISO 13934-1 1999
Part 1: Determination of maximum force
and elongation at maximum force using the
strip method
---------------------- Page: 5 ----------------------
SIST EN 60311:2003
---------------------- Page: 6 ----------------------
SIST EN 60311:2003
INTERNATIONAL IEC
STANDARD
60311
Fourth edition
2002-09
Electric irons for household or similar use –
Methods for measuring performance
Fers à repasser électriques pour usage domestique
ou analogue –
Méthodes de mesure de l'aptitude à la fonction
IEC 2002 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale
X
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue
---------------------- Page: 7 ----------------------
SIST EN 60311:2003
– 2 – 60311 IEC:2002(E)
CONTENTS
FOREWORD . 4
1 Scope and object . 6
2 Normative references. 6
3 Terms and definitions . 7
4 Measurements for various types of irons. 9
5 General conditions for measurements.10
5.1 Ambient conditions .10
5.2 Voltage for measurements .10
5.3 Steady conditions .10
5.4 Iron support for measurements .10
5.5 Temperature measurement.11
5.6 Cordless irons having a mains supply attachment.11
5.7 Irons fitted with separate steam generator/boiler.11
5.8 Irons fitted with auto switch-off devices.11
5.9 Test sample.11
6 General requirements .11
6.1 Determination of mass .11
6.2 Measurement of length of the supply cord.12
7 Temperature measurements .12
7.1 Measurement of heating-up time.12
7.2 Measurement of initial overswing temperature
and heating-up excess temperature .12
7.3 Measurement of sole-plate temperature.13
7.4 Determination of the hottest point .13
7.5 Measurement of temperature distribution .13
7.6 Measurement of cyclic fluctuation of temperature of the hottest point .14
8 Assessment of the spray function .14
8.1 Determination of the mass of spray.14
8.2 Determination of the spray pattern.15
9 Measurements concerning steaming operation .16
9.1 Measurement of heating-up time for steaming operation .16
9.2 Measurement of steaming time, steaming rate and water leakage rate.17
9.3 Determination of mass of a shot of steam .19
10 Assessment of smoothing .20
10.1 Creasing of test cloth.20
10.2 Conditioning of the iron.21
10.3 Ironing .21
10.4 Ironing with shot of steam.21
10.5 Evaluation .22
11 Measurement of input power and energy consumption .22
11.1 Measurement of input power.22
11.2 Measurement of energy consumption.22
---------------------- Page: 8 ----------------------
SIST EN 60311:2003
60311 © IEC:2002(E) – 3 –
12 Assessment of sole-plate.22
12.1 Determination of smoothness of the sole-plate.22
12.2 Measurement of scratch resistance of sole-plate .23
12.3 Determination of adhesion of polytetrafluorethylene (PTFE) coating
or similar coating on sole-plate .25
13 Measurement of thermostatic stability.25
13.1 Heating test .25
13.2 Drop test.26
13.3 Determination of drift of thermostat.26
14 Determination of total steaming time for hard water .26
15 Instruction for use.27
16 Information at the point of sale.28
Annex A (informative) Measurement of steaming time, steaming rate and water
leakage rate for pressurized steam irons or instantaneous steam irons .43
Annex B (normative) Ironing board.44
Annex C (normative) Cotton cloth.47
Annex D (informative) Classification of electric irons .48
Figure 1 – Arrangement for measuring the sole-plate temperature .29
Figure 2 – Variation of sole-plate temperature after switching-on .30
Figure 3 – Determination of spray pattern .31
Figure 4 – Test apparatus .32
Figure 5 – Creasing tool.33
Figure 6 – Wrapping rod and pencil.33
Figure 7 – Circular and rectangular blocks .34
Figure 8 – Conditioning of the iron .34
Figure 9 – Ironing.35
Figure 10 – Evaluation .35
Figure 12 – Test apparatus for smoothness of sole-plate .38
Figure 13 -- Scratch .39
Figure 14 – Positions of cutting area .40
Figure 15 – Apparatus for drop test .41
Figure 16 – Test apparatus for total steaming time.42
Figure A.1 – Measurements concerning steaming operation.43
Figure B.1 – Example of construction of the ironing board.46
Table 1 – Measurements of various types of irons. 9-10
Table 2 – Classes of scratch resistance .24
---------------------- Page: 9 ----------------------
SIST EN 60311:2003
– 4 – 60311 IEC:2002(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC IRONS FOR HOUSEHOLD
OR SIMILAR USE –
METHODS FOR MEASURING PERFORMANCE
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60311 has been prepared by subcommittee 59E: Ironing and
pressing appliances, of IEC technical committee 59: Performance of household electrical
appliances.
This fourth edition of IEC 60311 cancels and replaces the third edition published in 1995 and
its amendment 1 (1997) and amendment 2 (1999).
The text of this standard is based on the third edition, amendments 1 and 2 and the following
documents:
FDIS Report on voting
59E/148/FDIS 59E/149/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
Annexes B and C form an integral part of this standard.
Annexes A and D are for information only.
---------------------- Page: 10 ----------------------
SIST EN 60311:2003
60311 © IEC:2002(E) – 5 –
In this standard, the following print types are used:
— test specifications: in italic type
— notes: in small roman type
— other texts: in roman type
Words in bold in the text are defined in clause 3.
The committee has decided that the contents of this publication will remain unchanged until
February 2005. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 11 ----------------------
SIST EN 60311:2003
– 6 – 60311 IEC:2002(E)
ELECTRIC IRONS FOR HOUSEHOLD
OR SIMILAR USE –
METHODS FOR MEASURING PERFORMANCE
1 Scope
This International Standard applies to electric irons for household or similar use.
The purpose of this standard is to state and define the principal performance characteristics
of electric irons for household or similar use which are of interest to the user and to describe
the standard methods for measuring these characteristics.
Electric irons covered by this standard include
− dry irons;
− steam irons;
− spray irons;
− steam irons with separate water reservoir or boiler/generator having a capacity not
exceeding 5 l.
This standard is concerned neither with safety nor with performance requirements.
NOTE The primary characteristic to be taken into account in assessing the performance of an electric iron is its
basic ability to produce a smooth finish to textile materials, without risk of scorching or other damage. lt has not
proved possible to devise a single method which will measure this characteristic in a consistently reproducible way
and measurements have therefore been included to check certain factors, such as the temperature of the sole-
plate at the mid-point, sole-plate temperature distribution, etc., which affect the basic characteristic. In evaluating
the results, it must be realized that, while a very exceptional result in any one of them may significantly affect
performance, there is considerable latitude in the combination of results which will give satisfactory ironing
performance, and too much significance should not be attached to minor differences in any one result.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60051-1:1997, Direct acting indicating analogue electrical measuring instruments and
their accessories – Part 1: Definitions and general requirements common to all parts
IEC 60454-3-3:1998, Pressure-sensitive adhesive tapes for electrical purposes – Part 3:
Specifications for individual materials – Sheet 3: Polyester film tapes with rubber
thermoplastic adhesive
IEC 60734:2001, Household electrical applicances – Performance – Hard water for testing
ISO 105-F:1985, Textiles – Tests for colour fastness – Part F: Standard adjacent fabrics
ISO 1518:1992, Paints and varnishes – Scratch test
ISO 2409:1992, Paints and varnishes – Cross-cut test
ISO 3758:1991, Textiles – Care labelling code using symbols
ISO 3801:1977, Textiles – Woven fabrics – Determination of mass per unit length and mass
per unit area
---------------------- Page: 12 ----------------------
SIST EN 60311:2003
60311 © IEC:2002(E) – 7 –
ISO 6330:2000, Textiles – Domestic washing and drying procedures for textile testing
ISO 7211-2:1984, Textiles – Woven fabrics – Construction – Methods of analysis – Part 2:
Determination of number of threads per unit length
ISO 9073-2: 1995, Textiles – Test methods for nonwovens – Part 2: Determination of
thickness
ISO 13934-1:1999, Textiles – Tensile properties of fabrics – Part 1: Determination of
maximum force and elongation at maximum force using the strip method
3 Terms and definitions
For the purposes of this standard the following definitions apply.
3.1
electric iron
portable appliance, which has an electrically heated sole-plate and is used for ironing textile
materials
NOTE In this standard, "electric iron" is referred to as "iron".
3.2
thermostatic iron
iron fitted with a thermostat, the setting of which can be adjusted manually to alter the sole-
plate temperature over a range and maintain it within certain limits
3.3
electric iron with non-self-resetting thermal cut-out
iron fitted with a non-self-resetting thermal cut-out, such as a fusible link, for the purpose of
disconnecting the heating element if the iron attains excessive temperature
3.4
dry iron
iron having neither means to produce and supply steam nor to spray water onto textile
materials while ironing
3.5
steam iron
iron having means to produce and supply steam to textile materials while ironing.
It can be provided with means to supply a shot of steam
3.5.1
shot-of-steam iron
iron provided with means to supply a shot of steam to textile materials while ironing
3.5.2
shot of steam
single emission of an increased volume of steam from the sole-plate for a short duration
3.5.3
vented steam iron
steam iron in which steam is produced when the water contacts the sole-plate, the water
reservoir being at atmospheric pressure.
NOTE The water reservoir may be incorporated in the iron or connected by a hose to the iron.
---------------------- Page: 13 ----------------------
SIST EN 60311:2003
– 8 – 60311 IEC:2002(E)
3.5.4
pressurized steam iron
steam iron in which steam is produced in a boiler at a pressure exceeding 50 kPa
NOTE The boiler may be incorporated in the iron or connected by a hose to the iron.
3.5.5
instantaneous steam iron
steam iron in which small quantities of water are pumped from the water reservoir and in
which steam is produced when the water contacts the walls of the boiler/generator, the water
reservoir being at atmospheric pressure
NOTE The water reservoir and the boiler are connected to the iron by a tube.
3.6
spray iron
iron provided with means to spray water onto textile materials while ironing
3.7
rated voltage
3.7.1
rated voltage
voltage assigned to the iron by the manufacturer
3.7.2
rated voltage range
range of voltage assigned to the iron by the manufacturer, expressed in terms of its lower and
upper limits
3.8
rated input
input power of the iron under normal operating conditions assigned by the manufacturer
3.9
sole-plate
flat surface of the iron, which is heated electrically and pressed against textile materials while
ironing
3.10
mid-point
point of the sole-plate in the geometrical centre of the centre-line of the sole-plate.
If this point is on a steam outlet, a groove or a cover, the nearest point of the sole-plate on
the centre-line as is practicable is chosen
3.11
upright position
vertical still position for a heel-standing iron or normal resting position according to the
manufacturer's instructions for other than a heel-standing iron
3.12
cordless iron
3.12.1
cordless iron
iron which is connected to the supply mains only when placed on its stand
---------------------- Page: 14 ----------------------
SIST EN 60311:2003
60311 © IEC:2002(E) – 9 –
3.12.2
cordless iron having a mains supply attachment
cordless iron which is provided, in addition, with a detachable part to which the supply cord is
fixed, and which can be connected to the supply mains directly during ironing
3.13
auto switch-off device
device provided by the manufacturer to interrupt the heating element if the iron is not moved
for a stated period of time
4 Measurements for various types of irons
The performance of the iron is determined by the measurements indicated in table 1. Relevant
measurements for various types of irons are indicated in table 1 by x.
Measurements are performed in the order given in table 1.
Table 1 – Measurements of various types of irons
Thermo- Cordless
Thermostatic
static steam irons
dry irons with
Thermo- Thermo- irons with having
Item of non-self- Cordless
static dry static steam non-self a mains
measurement resetting irons
irons irons resetting supply
thermal
thermal attach-
cut out
cut out ment
6.1 (Determination of mass) x x x x x x
6.2 (Measurement of length
xx x x x x
of the supply cord)
7.1 (Measurement of
xx x x x x
heating-up time)
7.2 (Measurement of initial
overswing temperature
xx x x x x
and heating-up excess
temperature)
7.3 (Measurement of sole-
xx x x x x
plate temperature)
7.4 (Determination of the
xx x x x x
hottest point)
7.5 (Measurement of
xx x x x x
temperature distribution)
7.6 (Measurement of cyclic
fluctuation of
xx x x x x
temperature of the
hottest point)
8 (Assessment of spray
(x) (x) (x) (x) (x) (x)
function)
9.1 (Measurement of
heating-up time for xx x x x x
steaming operation)
9.2 (Measurement of
xx x
steaming time)
9.2 (Measurement of
xx x x
steaming rate)
9.3 (Determination of mass
(x) (x) (x) (x)
of a shot of steam)
10 (Assessment of
xx x x x x
smoothing)
10.4 (Ironing with shot
(x) (x) (x) (x)
of steam)
---------------------- Page: 15 ----------------------
SIST EN 60311:2003
– 10 – 60311 IEC:2002(E)
Thermo- Cordless
Thermostatic
static steam irons
dry irons with
Thermo- Thermo- irons with having
non-self- Cordless
Item of measurement static dry static steam non-self a mains
resetting irons
irons irons resetting supply
thermal
thermal attach-
cut out
cut out ment
11.1 (Measurement of
xx x x x x
input power)
11.2 (Measurement of energy
xx x x x x
consumption)
12.1 (Determination
of smoothness of xx x x x x
the sole-plate)
12.2 (Measurement of scratch
xx x x x x
resistance of sole-plate)
12.3 (Determination of
adhesion of polytetra-
fluorethylene (PTFE) xx x x x x
coating or similar coating
on sole-plate)
13 (Measurement of
xx x x x x
thermostatic stability)
14 (Determinati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.