SIST EN ISO 11960:2014
(Main)Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2014)
Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2014)
EN-ISO 11960 specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material and establishes requirements for three Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for PSL-1 are the basis of this International Standard. The requirements that define different levels of standard technical requirements for PSL-2 and PSL-3, for all Grades except H-40, L-80 9Cr and C110, are contained in Annex H. For pipes covered by this International Standard, the sizes, masses and wall thicknesses, as well as, grades and applicable end-finishes are listed in Tables C.1 and C.2 and Tables E.1 and E.2. By agreement between the purchaser and manufacturer, this International Standard can also be applied to other plain-end pipe sizes and wall thicknesses. This International Standard is applicable to the following connections in accordance with API Spec 5B: - short round thread casing (SC); - long round thread casing (LC); - buttress thread casing (BC); - non-upset tubing (NU); - external upset tubing (EU); - integral tubing (IJ). For such connections, this International Standard specifies the technical delivery conditions for couplings and thread protection. Supplementary requirements that can optionally be agreed for enhanced leak resistance connections (LC) are given in A.11 SR22. This International Standard can also be applied to tubulars with connections not covered by ISO/API standards. The four groups of products to which this International Standard is applicable include the following grades of pipe: - Group 1: All casing and tubing in Grades H, J, K, N and R; - Group 2: All casing and tubing in Grades C, L, M and T; - Group 3: All casing and tubing in Grade P; - Group 4: All casing in Grade Q. Casing sizes larger than Label 1: 4-1/2 but smaller than Label 1: 10-3/4 can be specified by the purchaser to be used in tubing service, see Tables C.1, C.23, C.27 and C.28 or Tables E.1, E.23, E.27 and E.28. Supplementary requirements that can optionally be agreed between purchaser and manufacturer for non-destructive examination, fully machined coupling blanks, upset casing, electric-welded casing, tubing and pup joints, impact testing, seal ring couplings, test certificates, tensile testing and sulfide stress cracking testing are given in Annex A. This International Standard is not applicable to threading requirements.
Erdöl- und Erdgasindustrie - Stahlrohre zur Verwendung als Futter- oder Steigrohre für Bohrungen (ISO 11960:2014)
Industries du pétrole et du gaz naturel - Tubes d'acier utilisés comme cuvelage ou tubes de production dans les puits (ISO 11960:2014)
ISO 11960:2014 spécifie les conditions de livraison techniques relatives aux tubes en acier (tubes de cuvelage, tubes de production et joints courts), tubes-ébauches de manchon, matériaux pour manchons et matériaux accessoires et établit des exigences pour trois niveaux de spécification de produit (PSL-1,1, PSL-2, PSL-3). Les exigences applicables au niveau PSL-1 constituent la base de la présente Norme internationale. Les exigences qui définissent différents niveaux d'exigences techniques standard pour les niveaux PSL-2 et PSL-3 et tous les grades, excepté H-40, L-80 9Cr et C110, sont indiquées à l'Annexe H.
Industrija za predelavo nafte in zemeljskega plina - Jeklene cevi, ki se uporabljajo kot zaščitne cevi ali cevovodi za vrtine (ISO 11960:2014)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11960:2014
01-april-2014
1DGRPHãþD
SIST EN ISO 11960:2011
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD-HNOHQHFHYLNLVHXSRUDEOMDMR
NRW]DãþLWQHFHYLDOLFHYRYRGL]DYUWLQH ,62
Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells
(ISO 11960:2014)
Erdöl- und Erdgasindustrie - Stahlrohre zur Verwendung als Futter- oder Steigrohre für
Bohrungen (ISO 11960:2014)
Industries du pétrole et du gaz naturel - Tubes d'acier utilisés comme cuvelage ou tubes
de production dans les puits (ISO 11960:2014)
Ta slovenski standard je istoveten z: EN ISO 11960:2014
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN ISO 11960:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11960:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 11960:2014
EUROPEAN STANDARD
EN ISO 11960
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2014
ICS 75.180.10; 77.140.75 Supersedes EN ISO 11960:2011
English Version
Petroleum and natural gas industries - Steel pipes for use as
casing or tubing for wells (ISO 11960:2014)
Industries du pétrole et du gaz naturel - Tubes d'acier Erdöl- und Erdgasindustrie - Stahlrohre zur Verwendung als
utilisés comme cuvelage ou tubes de production dans les Futter- oder Steigrohre für Bohrungen (ISO 11960:2014)
puits (ISO 11960:2014)
This European Standard was approved by CEN on 2 January 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11960:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11960:2014
EN ISO 11960:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11960:2014
EN ISO 11960:2014 (E)
Foreword
This document (EN ISO 11960:2014) has been prepared by Technical Committee ISO/TC 67 “Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries” in collaboration
with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by July 2014, and conflicting national standards shall be withdrawn at the
latest by July 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11960:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11960:2014 has been approved by CEN as EN ISO 11960:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11960:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 11960:2014
INTERNATIONAL ISO
STANDARD 11960
Fifth edition
2014-01-15
Petroleum and natural gas industries —
Steel pipes for use as casing or tubing for
wells
Industries du pétrole et du gaz naturel — Tubes d'acier utilisés comme
cuvelage ou tubes de production dans les puits
Reference number
ISO 11960:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 11960:2014
ISO 11960:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any
means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission.
Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO Copyright Office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11960:2014
ISO 11960:2014(E)
Contents Page
Foreword . vi
Introduction . vii
1 Scope . 1
2 Conformance . 2
2.1 Dual referencing of normative references . 2
2.2 Units of measurement . 2
3 Normative references . 2
4 Terms, definitions, symbols and abbreviated terms . 5
4.1 Terms and definitions . 5
4.2 Symbols and abbreviated terms . 9
5 Information to be supplied by the purchaser . 10
5.1 Grades C90, T95 and C110 . 10
5.2 Casing . 10
5.3 Tubing . 12
5.4 Coupling stock, coupling material and accessory material . 13
6 Process of manufacture . 14
6.1 General . 14
6.2 Heat treatment . 15
6.3 Straightening . 15
6.4 Traceability . 16
6.5 Processes requiring validation . 17
7 Material requirements . 17
7.1 Chemical composition . 17
7.2 Tensile properties . 17
7.3 Charpy V-notch test — General requirements . 18
7.4 Charpy V-notch — Absorbed energy requirements for coupling stock, coupling material,
coupling blanks and couplings . 20
7.5 Charpy V-notch — Absorbed energy requirements for pipe . 21
7.6 Charpy V-notch — Absorbed energy requirements for accessory material . 23
7.7 Maximum hardness . 23
7.8 Hardness variation — Grades C90, T95, C110 and Q125 . 24
7.9 Process control — Grades C90, T95, C110 and Q125 . 24
7.10 Hardenability — Minimum percentage martensite for quenched and tempered products . 24
7.11 Grain size — Grades C90, T95 and C110 . 25
7.12 Surface condition — Grades L80 9Cr and L80 13Cr . 25
7.13 Flattening — Electric-welded pipe . 25
7.14 Sulfide stress cracking test — Grades C90, T95 and C110 . 25
8 Dimensions, masses, tolerances, product ends and defects . 28
8.1 Labels and sizes . 28
8.2 Dimensions and masses. 28
8.3 Diameter . 29
8.4 Wall thickness . 29
8.5 Mass . 30
8.6 Length . 30
8.7 Casing jointers . 30
8.8 Height and trim of electric-weld flash . 30
8.9 Straightness . 31
8.10 Drift requirements . 31
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11960:2014
ISO 11960:2014(E)
8.11 Tolerances on dimensions and masses .32
8.12 Product ends .33
8.13 Defects .34
8.14 Coupling make-up and thread protection .35
9 Couplings .36
9.1 General requirements .36
9.2 Alternative grades or heat treatments .36
9.3 Mechanical properties .36
9.4 Dimensions and tolerances .37
9.5 Regular couplings.37
9.6 Special-clearance couplings — Groups 1, 2 and 3 .37
9.7 Combination couplings .37
9.8 Reducing couplings — Groups 1, 2 and 3 .37
9.9 Seal-ring couplings .37
9.10 Special-bevel tubing regular couplings — Groups 1, 2 and 3 .38
9.11 Threading .38
9.12 Surface inspection .38
9.13 Measurement of imperfections .39
9.14 Repair and removal of imperfections and defects .39
9.15 Thread surface treatment — Grade Q125 .39
9.16 Couplings and coupling blank protection — Grades C90, T95, C110 and Q125 .39
10 Inspection and testing .39
10.1 Test equipment .39
10.2 Lot definition for testing of mechanical properties .40
10.3 Testing of chemical composition .40
10.4 Tensile tests .41
10.5 Flattening test .44
10.6 Hardness test .45
10.7 Impact test .51
10.8 Grain size determination — Grades C90, T95 and C110 .52
10.9 Hardenability — Grades C90, T95 and C110 .53
10.10 Sulfide stress-cracking test — Grades C90, T95 and C110 .53
10.11 Metallographic evaluation — EW Grades P110 and Q125 .53
10.12 Hydrostatic tests .53
10.13 Dimensional testing .55
10.14 Visual inspection .58
10.15 Non-destructive examination (NDE) .59
11 Marking .66
11.1 General .66
11.2 Stamp marking requirements .67
11.3 Stencil marking requirements .68
11.4 Colour identification .69
11.5 Thread and end-finish marking — All groups .70
11.6 Pipe-threader marking requirements — All groups .70
12 Coating and protection .71
12.1 Coatings — All groups .71
12.2 Thread protectors .71
13 Documents .72
13.1 Electronic media — All groups .72
13.2 Certification — Groups 1, 2 (except Grade C110) and 3 .72
13.3 Certification requirements — Grades C110 and Q125 .72
13.4 Retention of records .72
14 Minimum facility requirements for various categories of manufacturer .72
14.1 Pipe mill .72
14.2 Processor .73
14.3 Pipe threader .73
14.4 Coupling, pup-joint or accessory manufacturer .73
iv © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11960:2014
ISO 11960:2014(E)
Annex A (normative) Supplementary requirements . 75
Annex B (normative) Purchaser inspection . 92
Annex C (normative) Tables in SI units . 93
Annex D (normative) Figures in SI (USC) units . 142
Annex E (normative) Tables in USC units . 167
Annex F (normative) Use of the API Monogram by Licensees . 215
Annex G (informative) Procedures used to convert from USC units to SI units . 222
Annex H (normative) Product Specification Levels . 234
Annex I (normative) Requirements for thread protector design validation . 241
Annex J (informative) Summary of Product Specification Level (PSL) requirements . 245
Annex K (normative) Modification of the hydrogen sulfide titration procedures in ANSI-NACE
TM0284-2003, Appendix C . 252
Annex L (informative) Technical changes from the previous edition . 253
Bibliography . 262
© ISO 2014 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 11960:2014
ISO 11960:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of
ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT)
see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 67, Materials, equipment and offshore structures for
petroleum and petrochemical and natural gas industries, Subcommittee SC 5, Casing, tubing and drill pipe.
This fifth edition cancels and replaces the fourth edition (ISO 11960:2011).
It is the intention of ISO/TC 67 that either this edition or the previous edition of ISO 11960 be applicable, at the
option of the purchaser (as defined in 4.1.39), for a period of six months from the first day of the calendar
quarter immediately following the date of publication of this edition, after which period the previous edition will
no longer be applicable.
vi © ISO 2014 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 11960:2014
ISO 11960:2014(E)
Introduction
This International Standard is based on API Spec 5CT.
Users of this International Standard are advised that further or differing requirements can be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the
purchaser from accepting, alternative equipment or engineering solutions for the individual application. This
can be particularly applicable where there is innovative or developing technology. Where an alternative is
offered, it is advisable that the vendor identify any variations from this International Standard and provide
details.
This International Standard includes requirements of various nature. These are identified by the use of certain
verbal forms:
SHALL is used to indicate that a provision is MANDATORY;
SHOULD is used to indicate that a provision is not mandatory, but RECOMMENDED as good practice;
MAY is used to indicate that a provision is OPTIONAL.
Details of the major changes (additions, modifications and deletions) agreed by the committee, and which
affect the performance of the products or the technical requirements applicable to the products, are provided
for information in Annex L and are indicated in this International Standard by the use of grey shading for
changes in the fourth edition and yellow shading for changes in this edition. Shading is also used to indicate
editorial changes. Where deletions, but no other changes, have been made, vertical bars are used in the
margin adjacent to the applicable line or at each side of a cell in a table. Where a complete line or paragraph
has been deleted, margin bars next to a blank line are used. While efforts have been made to ensure the
accuracy of the changes indicated, the user of this International Standard is advised to consider the total
technical content and not only the changes identified. The user is ultimately responsible for recognising any
differences between this edition and the previous edition of this International Standard. ISO expressly
disclaims any liability or responsibility for loss or damage resulting from inappropriate use of this International
Standard on the basis of any inaccuracy in the changes identified.
© ISO 2014 – All rights reserved vii
---------------------- Page: 13 ----------------------
SIST EN ISO 11960:2014
---------------------- Page: 14 ----------------------
SIST EN ISO 11960:2014
INTERNATIONAL STANDARD ISO 11960:2014(E)
Petroleum and natural gas industries — Steel pipes for use as
casing or tubing for wells
1 Scope
1.1 This International Standard specifies the technical delivery conditions for steel pipes (casing, tubing and
pup joints), coupling stock, coupling material and accessory material and establishes requirements for three
Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for PSL-1 are the basis of this
International Standard. The requirements that define different levels of standard technical requirements for
PSL-2 and PSL-3, for all Grades except H-40, L-80 9Cr and C110, are contained in Annex H.
For pipes covered by this International Standard, the sizes, masses and wall thickness
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.